The Implications of Bach's Introduction of New Fugal Techniques and Procedures in the Well-Tempered Clavier Book Two

Among the fugues of the WTC II, there are some fugal techniques and procedures that were not explored in the first book. Here, the ‘fugal techniques’ include parallel entries (as used in the fugues in D-sharp minor, G minor and B-flat minor) and double counterpoint at the tenth or twelfth as well as fifteenth (as used in the fugues in G minor and B major). The ‘fugal procedures’, on the other hand, refer to meticulously planned multi-exposition architecture (as seen in the fugues in F-sharp minor exploiting two subsidiary subjects, and B-flat minor exploiting inversion and stretto) and a form in which the appearance of the subsidiary subject is gradually predicted in the fugal discourse (viz. C-sharp minor, G-sharp minor and B major). All these new ideas helped Bach to write more dramatic, more profound fugues for WTC II. The paper will consider how Bach came to acquire the new techniques and to use them in such ways, and what motivated him to adopt these new compositional approaches. Do they offer any clues for our better understanding of why Bach compiled the WTC II?

Rotational Molding Cycle Time Reduction Using a Combination of Physical Techniques

Rotational molding is a process used to manufacture hollow plastic products, and has been heralded as a molding method with great potential. Reduction of cycle times is an important issue for the rotational molding industry, addressing a significant disadvantage of the process. Previous attempts to reduce cycle times have addressed surface enhanced molds, internal pressure, internal cooling, water spray cooling, and higher oven air flow rates within the existing process. This article explores the potential benefits of these cycle time reduction techniques, and combinations of them. Recommendations on a best practice combination are made, based on experimental observations and resulting product quality. Applying the proposed molding conditions (i.e., a combination of surface-enhanced molds, higher oven flow rates, internal mold pressure, and water spray cooling), cycle time reductions of up to 70% were achieved. Such savings are very significant, inviting the rotomolding community to incorporate these techniques efficiently in an industrial setting. POLYM. ENG. SCI., 49:1846-1854, 2009. (C) 2009 Society of Plastics Engineers

Comparison of techniques to screen and characterize bacteria-specific hybridomas for high-quality monoclonal antibodies selection

Antibodies are are very important materials for diagnostics. A rapid and simple hybridoma screening method will help in delivering specific monoclonal antibodies. In this study, we systematically developed the first antibody array to screen for bacteria-specific monoclonal antibodies using Listeria monocytogenes as a bacteria model. The antibody array was developed to expedite the hybridoma screening process by printing hybridoma supernatants on a glass slide coated with an antigen of interest. This screening method is based on the binding ability of supernatants to the coated antigen. The bound supernatants were detected by a fluorescently labeled anti-mouse immunoglobulin. Conditions (slide types, coating, spotting, and blocking buffers) for antibody array construction were optimized. To demonstrate its usefulness, antibody array was used to screen a sample set of 96 hybridoma supernatants in comparison to ELISA. Most of the positive results identified by ELISA and antibody array methods were in agreement except for those with low signals that were undetectable by antibody array. Hybridoma supernatants were further characterized with surface plasmon resonance to obtain additional data on the characteristics of each selected clone. While the antibody array was slightly less sensitive than ELISA, a much faster and lower cost procedure to screen clones against multiple antigens has been demonstrated. (C) 2011 Elsevier Inc. All rights reserved.

A comparative study of three techniques for determining photocatalytic activity

Quantitative measurement of the activity of photoactive films is an area of importance. The establishment of tests for standardisation of performance is important for efficient research but also a major milestone in achieving technology acceptance. In this paper, we compare three different techniques across a range of film samples from various sources. Furthermore, we demonstrate the potential of the dye-based approach as a quick and simple test. A series of photoactive film samples are compared for measured activity against each test. The test is shown to be capable of reproducible and quantitative activity results. The test has potential for use