Using Mesh-Geometry Relationships to Transfer Analysis Models between CAE Tools

Integrating analysis and design models is a complex task due to differences between the models and the architectures of the toolsets used to create them. This complexity is increased with the use of many different tools for specific tasks during an analysis process. In this work various design and analysis models are linked throughout the design lifecycle, allowing them to be moved between packages in a way not currently available. Three technologies named Cellular Modeling, Virtual Topology and Equivalencing are combined to demonstrate how different finite element meshes generated on abstract analysis geometries can be linked to their original geometry. Establishing the equivalence relationships between models enables analysts to utilize multiple packages for specialist tasks without worrying about compatibility issues or rework.

Experimental and numerical studies on rock breaking with TBM tools under high stress confinement

The understanding of rock breaking and chipping due to the TBM cutter disks mechanism in deep tunnels is considered in this paper. The interest stems from the use of TBMs for the excavation of long Trans-Alpine tunnels. Some tests that simulate the disk cutter action at the tunnel face by means of an indenter, acting on a rock specimen are proposed. The rock specimen is confined through a flat-jack and a confinement-free area on one side of the specimen simulates the formation of a groove near the indenter, like it occurs in TBM excavation conditions. Results show a limited influence of the confinement stress versus the thrust increment required for breaking the rock between the indenter and the free side of the specimen. Numerical modelling of the cutter disk action on confined material has also been carried out in order to investigate further aspects of the fracture initiation. Also in this case the importance of the relative position between disk cutter and groove is pointed out. © 2006 Springer-Verlag.

A statistical process control approach for automatic anti-islanding detection using synchrophasors

Anti-islanding protection is becoming increasingly important due to the rapid installation of distributed generation from renewable resources like wind, tidal and wave, solar PV, bio-fuels, as well as from other resources like diesel. Unintentional islanding presents a potential risk for damaging utility plants and equipment connected from the demand side, as well as to public and personnel in utility plants. This paper investigates automatic islanding detection. This is achieved by deploying a statistical process control approach for fault detection with the real-time data acquired through a wide area measurement system, which is based on Phasor Measurement Unit (PMU) technology. In particular, the principal component analysis (PCA) is used to project the data into principal component subspace and residual space, and two statistics are used to detect the occurrence of fault. Then a fault reconstruction method is used to identify the fault and its development over time. The proposed scheme has been used in a real system and the results have confirmed that the proposed method can correctly identify the fault and islanding site.

Delamination and wear in drilling of carbon-fiber reinforced plastic composites using multilayer TiAlN/TiN PVD-coated tungsten carbide tools

This study aims to investigate drilling process in carbon-fiber reinforced plastic (CFRP) composites with multilayer TiAlN/TiN PVD-coated tungsten carbide drill. The effect of process parameters have been investigated in drilling of Hexcel M21-T700GC. Thrust force and torque were measured online throughout the drilling experiments. Delamination were observed using optical microscope and analyzed via a developed algorithm based on digital image processing technique. Surface roughness of each hole was measured using a surface profilometer. In addition, the progression of tool wear in various surfaces of drill was observed using tool microscope and measured using image software. Our results indicate that the thrust force and torque increased with the increasing cutting speed and feed rate. Delamination and average surface roughness that rose with the increase in feed rate, however, decreased with the increasing cutting speed. The average surface roughness tended to increase with the increase in feed rate and decrease with the increasing cutting speed in drilling of carbon-fiber reinforced plastic (CFRP). Feed rate was found as the predominant factor on the drilling outputs. Abrasive wear was observed on both flank and relief surfaces, which created edge wear on cutting edges. No sign of chipping or plastic deformation has been observed on the surfaces of drills. © 2012 The Author(s).

Brunetta’s reform swan song? An assessment of its success in local governments through the analysis of its tools

The work aims at assessing the success of Brunetta’s reform (Legislative Decree n. 150/2009), a far-reaching reform that aimed at improving both organizational and individual performance in Italian public administration through a specific planning and control process (the performance cycle) and most of all through two new tools, Performance Plan and Performance Report. The success of the reform is assessed, with particular emphasis on local governments, analyzing the diffusion and use of these new tools. The study has been conducted using a deductive-inductive methodology. Thus, after a study of managerial reforms in Italy and performance measurement literature, a possible model (PerformEL Model) local governments could follow to draw up Performance Plan and Report as effective tools for performance measurement has been designed (deductive phase). Performance Plans 2011-2013 and Performance Report 2011 downloaded from Italian big sized municipalities’ websites have been analyzed in the light of PerformEL Model, to assess the diffusion of the documents and their coherence with legal requirements and suggestions from literature (inductive phase). Data arising from the empirical analysis have been studied to evaluate the diffusion and the effectiveness of big sized municipalities’ Performance Plans and Reports as performance measurement tools and thus to assess the success of the reform (feedback phase). The study shows a scarce diffusion of the documents; they are mostly drew up because of their compulsoriness or to gain legitimization. The results testify the failure of Brunetta’s reform, at least with regard to local governments.

Tools for Finding Inconsistencies in Real-world Logic-based Systems

Currently there is extensive theoretical work on inconsistencies in logic-based systems. Recently, algorithms for identifying inconsistent clauses in a single conjunctive formula have demonstrated that practical application of this work is possible. However, these algorithms have not been extended for full knowledge base systems and have not been applied to real-world knowledge. To address these issues, we propose a new algorithm for finding the inconsistencies in a knowledge base using existing algorithms for finding inconsistent clauses in a formula. An implementation of this algorithm is then presented as an automated tool for finding inconsistencies in a knowledge base and measuring the inconsistency of formulae. Finally, we look at a case study of a network security rule set for exploit detection (QRadar) and suggest how these automated tools can be applied.

Using mesh-geometry relationships to transfer analysis models between CAE tools

Integrating analysis and design models is a complex task due to differences between the models and the architectures of the toolsets used to create them. This complexity is increased with the use of many different tools for specific tasks using an analysis process. In this work various design and analysis models are linked throughout the design lifecycle, allowing them to be moved between packages in a way not currently available. Three technologies named Cellular Modeling, Virtual Topology and Equivalencing are combined to demonstrate how different finite element meshes generated on abstract analysis geometries can be linked to their original geometry. Cellular models allow interfaces between adjacent cells to be extracted and exploited to transfer analysis attributes such as mesh associativity or boundary conditions between equivalent model representations. Virtual Topology descriptions used for geometry clean-up operations are explicitly stored so they can be reused by downstream applications. Establishing the equivalence relationships between models enables analysts to utilize multiple packages for specialist tasks without worrying about compatibility issues or substantial rework.