On the complexity of the water-gas shift reaction mechanism over a Pt/CeO2 catalyst: Effect of the temperature on the reactivity of formate surface species studied by operando DRIFT during isotopic transient at chemical steady-state

The present report investigates the role of formate species as potential reaction intermediates for the WGS reaction (CO + H2O -> CO2 + H-2) over a Pt-CeO2 catalyst. A combination of operando techniques, i.e., in situ diffuse reflectance FT-IR (DRIFT) spectroscopy and mass spectrometry (MS) during steady-state isotopic transient kinetic analysis (SSITKA), was used to relate the exchange of the reaction product CO2 to that of surface formate species. The data presented here suggest that a switchover from a non-formate to a formate-based mechanism could take place over a very narrow temperature range (as low as 60 K) over our Pt-CeO2 catalyst. This observation clearly stresses the need to avoid extrapolating conclusions to the case of results obtained under even slightly different experimental conditions. The occurrence of a low-temperature mechanism, possibly redox or Mars van Krevelen-like, that deactivates above 473 K because of ceria over-reduction is suggested as a possible explanation for the switchover, similarly to the case of the CO-NO reaction over Cu, I'd and Rh-CeZrOx (see Kaspar and co-workers [1-3]). (c) 2006 Elsevier B.V. All rights reserved.

A DFT study of the chain growth probability in Fischer-Tropsch synthesis

The chain growth probability (alpha value) is one of the most significant parameters in Fischer-Tropsch (FT) synthesis. To gain insight into the chain growth probability, we systematically studied the hydrogenation and C-C coupling reactions with different chain lengths on the stepped Co(0001) surface using density functional theory calculations. Our findings elucidate the relationship between the barriers of these elementary reactions and the chain length. Moreover, we derived a general expression of the chain growth probability and investigated the behavior of the alpha value observed experimentally. The high methane yield results from the lower chain growth rate for C-1 + C-1 coupling compared with the other coupling reactions. After C-1, the deviation of product distribution in FT synthesis from the Anderson-Schulz-Flory distribution is due to the chain length-dependent paraffin/olefin ratio. (C) 2008 Elsevier Inc. All rights reserved.

A quantitative determination of reaction mechanisms from density functional theory calculations: Fischer-Tropsch synthesis on flat and stepped cobalt surfaces

We systematically investigated the mechanism of the C-1 + C-1 coupling reactions using density functional theory. The activation energies of C-1 + C-1 coupling and carbon hydrogenation reactions on both flat and stepped surfaces were calculated and analyzed. Moreover, the coverages of adsorbed C-1 species were estimated, and the reaction rates of all possible C-1 + C-1 coupling pathways were quantitatively evaluated. The results suggest that the reactions of CH2 + CH2 and CH3 + C at steps are most likely to be the key C-1 + C-1 coupling steps in FT synthesis on Co catalysts. The reactions of C-2 + C-1 and C-3 + C-1 coupling also were studied; the results demonstrate that in addition to the pathways of RCH + CH2 and RCH2 + C, the coupling of RC + C and RC + CH also may contribute to the chain growth after C-1. (C) 2008 Elsevier Inc. All rights reserved.

Supported and liquid phase task specific ionic liquids for base catalysed Knoevenagel reactions

A series of Hunig's base tethered ammonium ionic liquids have been used to catalyse the Knoevenagel condensation of aldehydes/ketones with malononitrile and ethyl cyanoacetate. The reactions were performed under homogeneous and under biphasic, liquid-liquid and liquid-silica supported ionic liquid, conditions with the biphasic systems employing cyclohexene as the second phase. By increasing the distance between the ammonium head group and Hunig's base the activity of the catalyst was found to increase. Higher activity, in general, was found under homogeneous reaction conditions; however, the recyclability of the catalyst was improved by supporting the BIL under biphasic conditions. (c) 2007 Elsevier B.V. All rights reserved.

Utilisation of ionic liquid solvents for the synthesis of Lily-of-the-Valley fragrance {beta-Lilial (R); 3-(4-t-butylphenyl)-2-methylpropanal}

The Heck arylation of 2-methylprop-2-en- I -ol in ionic liquids and organic solvents is reported using a range of homogeneous and heterogeneous palladium catalysts. Higher activity is observed in the ionic liquid media compared with N-methyl pyrrolidinone and under solventless conditions. The ionic liquid-catalyst system may be recycled easily with little loss in activity, although significant palladium leaching from the heterogeneous catalyst was observed. In the case of Trans-bis(2,3-dihydro-3-methylbenzothiazole-2-ylidene)diiodopalladium (11) reported to be highly active for this transformation, significant induction petiods were observed indicating that nanoparticles may be responsible for the catalysis. Using the ionic liquid Heck reaction, a recyclable synthesis for the fragrance beta-Lilial((R)) has been developed. (c) 2004 Elsevier B.V. All rights reserved.

Use of a batch rotating photocatalytic contactor for the degradation of organic pollutants in wastewater

Aqueous solutions of a chlorinated VOC, 3,4-dichlorobut-1-ene, as well as other pollutants, may be mineralised to carbon dioxide, water and hydrochloric acid using a sealed rotating photocatalytic reactor. The effect of pH, dissolved oxygen concentration, light intensity, pollutant concentration and rotation speed on the degradation rate have been investigated as well as competition kinetics with methanol. This reactor may be optimised to minimise competition effects in mixed solutions. (C) 2001 Elsevier Science B.V. All rights reserved.

A density functional theory study of the a-olefin selectivity in Fischer-Tropsch synthesis

We studied the alpha-olefin selectivity in Fischer-Tropsch (FT) synthesis using density functional theory (131717) calculations. We calculated the relevant elementary steps from C-2 to C-6 species. Our results showed that the barriers of hydrogenation and dehydrogenation reactions were constant with different chain lengths, and the chemisorption energies of alpha-olefins from DFT calculations also were very similar, except for C-2 species. A simple expression of the paraffin/olefin ratio was obtained based on a kinetic model. Combining the expression of the paraffin/olefin ratio and our calculation results, experimental findings are satisfactorily explained. We found that the physical origin of the chain length dependence of paraffin/olefin ratio is the chain length dependence of both the van der Waals interaction between adsorbed alpha-olefins and metal surfaces and the entropy difference between adsorbed and gaseous alpha-olefins, and that the greater chemisorption energy of ethylene is the main reason for the abnormal ethane/ethylene ratio. (c) 2008 Elsevier Inc. All rights reserved.

On the need to use steady-state or operando techniques to investigate reaction mechanisms: An in situ DRIFTS and SSITKA-based study example

The nature of the surface species formed at the surface of 2 wt.% Pt/CeO2 catalyst during the forward water-gas-shift (WGS, CO + H2O -> CO2 + H-2) and the reverse reaction (RWGS) were essentially identical. More, the surface concentration of formate, carbonate and carbonyl species was similar in each case. The presence of well-resolved IR bands allowed an unequivocal relative quantitative analysis of each species, avoiding the use of the carboxylate stretching region (1600-1200 cm(-1)). However, the quantitative analysis in the case of an isotopic study was complicated due to the overlapping of the various isotope bands, yet this problem could be overcome by integrating the high-wavenumber part of the bands. The reactivity of the surface species formed under RWGS conditions was followed under two different gaseous streams. Firstly, the reactivity of these intermediates were followed under an inert gas (i.e., At), in which case carbonates were essentially stable and less reactive than formates. Secondly, the reactivity of the same surface species was followed when switching to the corresponding C-13-labelled feed (i.e., (CO2)-C-13 + H-2), in which case carbonates were exchanged significantly faster than formates. While carbonates species have been reported as reaction intermediate under reaction conditions, the increased stability or surface poisoning by these carbonates in the absence of reaction mixture was highlighted. Ultimately, this work re-emphasises the need to use steady-state conditions if the true operando reactivity of the adsorbates and structure of the solid are to be determined. (c) 2005 Elsevier B.V. All rights reserved.

Steam reforming of model compounds and fast pyrolysis bio-oil on supported noble metal catalysts

The production of hydrogen by steam reforming of bio-oils obtained from the fast pyrolysis of biomass requires the development of efficient catalysts able to cope with the complex chemical nature of the reactant. The present work focuses on the use of noble metal-based catalysts for the steam reforming of a few model compounds and that of an actual bio-oil. The steam reforming of the model compounds was investigated in the temperature range 650-950 degrees C over Pt, Pd and Rh supported on alumina and a ceria-zirconia sample. The model compounds used were acetic acid, phenol, acetone and ethanol. The nature of the support appeared to play a significant role in the activity of these catalysts. The use of ceria-zirconia, a redox mixed oxide, lead to higher H-2 yields as compared to the case of the alumina-supported catalysts. The supported Rh and Pt catalysts were the most active for the steam reforming of these compounds, while Pd-based catalysts poorly performed. The activity of the promising Pt and Rh catalysts was also investigated for the steam reforming of a bio-oil obtained from beech wood fast pyrolysis. Temperatures close to, or higher than, 800 degrees C were required to achieve significant conversions to COx and H-2 (e.g., H-2 yields around 70%). The ceria-zirconia materials showed a higher activity than the corresponding alumina samples. A Pt/ceria-zirconia sample used for over 9 h showed essentially constant activity, while extensive carbonaceous deposits were observed on the quartz reactor walls from early time on stream. In the present case, no benefit was observed by adding a small amount of O-2 to the steam/bio-oil feed (autothermal reforming, ATR), probably partly due to the already high concentration of oxygen in the bio-oil composition. (c) 2005 Elsevier B.V. All rights reserved.

Steric effects in the selective hydrogenation of cinnamaldehyde to cinnamyl alcohol using an Ir/C catalyst

The liquid phase selective hydrogenation of cinnamaldehyde to cinnamyl alcohol has been carried out over a graphite-supported iridium catalyst. The effect of reaction parameters such as temperature, pressure, concentration of reactant, the effect of addition of product to the feed and pre-reduction of the catalyst were studied. In situ pre-reduction of the catalyst with hydrogen had a very significant enhancing effect on the conversion of cinnamaldehyde and selectivity of the catalyst to cinnamyl alcohol. Kinetic analysis of the pre-reduced catalyst showed that the reaction is zero order with respect to cinnamaldehyde and first order with respect to hydrogen. The reaction follows an Arrhenius behaviour with an activation energy of 37 kJ mol(-1). Detailed analysis of the reaction showed that hydrogenation of the C=C double bond to give hydrocinnamaldehyde predominantly occurred at low conversions of cinnamaldehyde (

An investigation of alternative catalytic approaches for the direct synthesis of hydrogen peroxide from hydrogen and oxygen

Catalytic systems for the direct production of hydrogen peroxide from hydrogen and oxygen are investigated, and the factors which make a successful process identified. The use of low metal loadings, an organic co-solvent (such as ethanol) and reduced palladium as the catalytic metal all lead to good activity and selectivity. (C) 2002 Elsevier Science B.V. All rights reserved.

The effect of the addition of sodium compounds in the liquid-phase hydrodechlorination of chlorobenzene over palladium catalysts

The hydrodechlorination of chlorobenzene over supported palladium catalysts has been studied. The palladium catalysts: deactivate as the reaction proceeds due to the HCl formed as by-product. The effect of the addition of sodium compounds has been analysed for the neutralisation of HCl. When NaOH was added to the reaction mixture, no beneficial effect was observed due to the detrimental effect of the alkaline medium on the textural and metallic properties of the catalysts. Doping the support with NaOH prior to impregnation with the metal precursor leads (after calcination and reduction) to catalysts with better activity and tolerance to deactivation, especially those obtained when using PdCl2 as the metal precursor. Low metal dispersion and the capture of chloride by forming NaCl are the: main factors contributing to the: improved catalytic properties. Finally, doping the catalysts with NaOH or NaNO3, after reduction of the metal precursor leads to a moderate increase in initial activity and final conversion, although NaOH impregnation also gave rise to support corrosion and metal dispersion modification. (C) 2001 Elsevier Science B.V, All rights reserved.

Microcolumn studies of dye adsorption onto manganese oxides modified diatomite

The method described here cannot fully replace the analysis of large columns by small test columns (microcolumns). The procedure, however, is suitable for speeding up the determination of adsorption parameters of dye onto the adsorbent and for speeding up the initial screening of a large adsorbent collection that can be tedious if a several adsorbents and adsorption conditions must be tested. The performance of methylene blue (MB), a basic dye, Cibacron reactive black (RB) and Cibacron reactive yellow (RY) was predicted in this way and the influence of initial dye concentration and other adsorption conditions on the adsorption behaviour were demonstrated.

Sorption behavior of cationic and anionic dyes from aqueous solution on different types of activated carbons

The effect of dye molecular charges on their adsorption from solution was investigated by using different types of activated carbon adsorbents. Two types of model systems were used representing cationic and anionic dyes. Screening investigations using single point tests were used throughout the study. Cationic dyes, of which Methylene Blue is an example, showed a higher adsorption tendency towards activated carbon over anionic dyes represented by an ate-type reactive compound. Of the number of activated carbons tested, only one of the adsorbents showed an exception to this behavior, and a good relation was observed between Methylene Blue capacity and activated carbon performance. The high capacity of cationic dyes in comparison to anionic dyes was also evident in the results obtained by a preliminary kinetic study carried out on the selected systems. Surface net charge of activated carbon and the nature of attractions between the molecules were suggested to be one of the reasons attributed for this behavior.

Enzymatic and chemoenzymatic synthesis of arene trans-dihydrodiols

Several potential approaches to the enzyme-catalysed synthesis of arene trans-diols have been examined including epoxidation/hydrolysis, bis-benzylic hydroxylation, cis-dihydroxylation/alcohol dehydrogenation/ketone reduction, cisdihydroxylation/cis-trans isomerisation. and multi-enzyme synthesis of trans-dihydrodiol secondary metabolites from primary metabolites. The lack of general applicability of these enzymatic methods has led to the development of several chemoenzymatic routes for the synthesis of a series of trans-dihydrodiols from the readily available cis-dihydrodiol precursors. Partial hydrogenation of cis-dihydrodiol metabolites to yield the corresponding cis-tetrahydrodiols followed by a regioselective Mitsunobu inversion process gave trans-tetrahydrodiols that were in turn converted to trans-dihydrodiols. The formation of anti-benzene dioxides or iron tricarbonyl complexes from the corresponding cis-dihydrodiol precursors provided shorter and more convenient chemoenzymatic routes to trans-dihydrodiols. The application of cis-dihydrodiol metabolites of polycyclic azaarenes in the synthesis of the corresponding arene oxides followed by chemical hydrolysis provides a convenient route to trans-dihydrodiols. (C) 2002 Elsevier Science B.V. All rights reserved.