Detection of Groundwater flow zones in low productivity boreholes (Submitted)

Conventional methods of detecting groundwater flow zones in open boreholes installed in fractured bedrock aquifers rely on either contrasts in water quality or on significant rates of vertical flow. In low productivity boreholes these methods have proced of limited value. Tracer tests completed in six low productivity bedrock boreholes installed into fresh Precambrian crystalline bedrock revealed measurable dilution, despite very low tranmissivities. Fluorescent tracer profiles generated during discharge pumping permitted identification of the principle zones contributing to flow. High resolution acoustic televiewer strike and dip measurements of fractures corresponding to these zones revealed a consistent pattern of regional lineament trends and suggested a strongly anisotropic flow pattern in bedrock.

Identification of low inorganic and total grain arsenic rice cultivars from Bangladesh

For the world's population, rice consumption is a major source of inorganic arsenic (As), a nonthreshold class 1 carcinogen. Reducing the amount of total and inorganic As within the rice grain would reduce the exposure risk. In this study, grain As was measured in 76 cultivars consisting of Bangladeshi landraces, improved Bangladesh Rice Research Institute (BRRI) cultivars, and parents of permanent mapping populations grown in two field sites in Bangladesh, Faridpur and Sonargaon, irrigated with As-contaminated tubewell water. Grain As ranged from 0.16 to 0.74 mg kg(-1) at Faridpur and from 0.07 to 0.28 mg kg(-1) at Sonargaon. Highly significant cultivar differences were detected and a significant correlation (r = 0.802) in the grain As between the two field sites was observed, indicating stable genetic differences in As accumulation. The cultivars with the highest concentration of grain As were the Bangladeshi landraces. Landraces with red bran had significantly more grain As than the cultivars with brown bran. The percent of inorganic As decreased linearly with increasing total As, but genetic variation within this trend was identified. A number of local cultivars with low grain As were identified. Some tropical japonica cultivars with low grain As have the potential to be used in breeding programs and genetic studies aiming to identify genes which decrease grain As.

Cooking rice in a high water to rice ratio reduces inorganic arsenic content

Total arsenic and arsenic speciation was performed on different rice types (basmati, long-grain, polished ([white] and wholegrain [brown]) that had undergone various forms of cooking. The effect of rinse washing, low volume (2.5 : 1 water : rice) and high volume (6 : 1 water : rice) cooking, as well as steaming, were investigated. Rinse washing was effective at removing circa. 10% of the total and inorganic arsenic from basmati rice, but was less effective for other rice types. While steaming reduced total and inorganic arsenic rice content, it did not do so consistently across all rice types investigated. Low volume water cooking did not remove arsenic. High volume water : rice cooking did effectively remove both total and inorganic arsenic for the long-grain and basmati rice (parboiled was not investigated in high volume cooking water experiment), by 35% and 45% for total and inorganic arsenic content, respectively, compared to uncooked (raw) rice. To reduce arsenic content of cooked rice, specifically the inorganic component, rinse washing and high volume of cooking water are effective.

Synthesis of spherical ultra-high-surface-area monodisperse amphipathic polymer sponges in the low-micrometer size range

Spherical, ultra-high specific surface area monodisperse polymer particles with diameters in the low micrometer size range are disclosed for the first time. The polymer particles are able to sorb significant levels of both hydrocarbon solvents and water, acting in effect as amphipathic micro-sponges. Exciting possibilities for exploitation of the particles in chromatography, diagnostics, sensors, delivery vehicles and catalysis are suggested.

On the required shape corrections to the local density and generalized gradient approximations to the Kohn-Sham potentials for molecular response calculations of (hyper)polarizabilities and excitation energies

It is well known that shape corrections have to be applied to the local-density (LDA) and generalized gradient (GGA) approximations to the Kohn-Sham exchange-correlation potential in order to obtain reliable response properties in time dependent density functional theory calculations. Here we demonstrate that it is an oversimplified view that these shape corrections concern primarily the asymptotic part of the potential, and that they affect only Rydberg type transitions. The performance is assessed of two shape-corrected Kohn-Sham potentials, the gradient-regulated asymptotic connection procedure applied to the Becke-Perdew potential (BP-GRAC) and the statistical averaging of (model) orbital potentials (SAOP), versus LDA and GGA potentials, in molecular response calculations of the static average polarizability alpha, the Cauchy coefficient S-4, and the static average hyperpolarizability beta. The nature of the distortions of the LDA/GGA potentials is highlighted and it is shown that they introduce many spurious excited states at too low energy which may mix with valence excited states, resulting in wrong excited state compositions. They also lead to wrong oscillator strengths and thus to a wrong spectral structure of properties like the polarizability. LDA, Becke-Lee-Yang-Parr (BLYP), and Becke-Perdew (BP) characteristically underestimate contributions to alpha and S-4 from bound Rydberg-type states and overestimate those from the continuum. Cancellation of the errors in these contributions occasionally produces fortuitously good results. The distortions of the LDA, BLYP, and BP spectra are related to the deficiencies of the LDA/GGA potentials in both the bulk and outer molecular regions. In contrast, both SAOP and BP-GRAC potentials produce high quality polarizabilities for 21 molecules and also reliable Cauchy moments and hyperpolarizabilities for the selected molecules. The analysis for the N-2 molecule shows, that both SAOP and BP-GRAC yield reliable energies omega(i) and oscillator strengths f(i) of individual excitations, so that they reproduce well the spectral structure of alpha and S-4.(C) 2002 American Institute of Physics.

Rational screening low-cost counter electrodes for dye-sensitized solar cells

Dye-sensitized solar cells have attracted intense research attention owing to their ease of fabrication, cost-effectiveness and high efficiency in converting solar energy. Noble platinum is generally used as catalytic counter electrode for redox mediators in electrolyte solution. Unfortunately, platinum is expensive and non-sustainable for long-term applications. Therefore, researchers are facing with the challenge of developing low-cost and earth-abundant alternatives. So far, rational screening of non-platinum counter electrodes has been hamstrung by the lack of understanding about the electrocatalytic process of redox mediators on various counter electrodes. Here, using first-principle quantum chemical calculations, we studied the electrocatalytic process of redox mediators and predicted electrocatalytic activity of potential semiconductor counter electrodes. On the basis of theoretical predictions, we successfully used rust (alpha-Fe2O3) as a new counter electrode catalyst, which demonstrates promising electrocatalytic activity towards triiodide reduction at a rate comparable to platinum.

Physiotherapy for Sleep Disturbance in People With Chronic Low Back Pain:Results of a Feasibility Randomized Controlled Trial

Objective: To determine the feasibility of a randomized controlled trial investigating the effectiveness of physiotherapy for sleep disturbance in chronic low back pain (CLBP) (=12wks). Design: Randomized controlled trial with evaluations at baseline, 3 months, and 6 months. Setting: Outpatient physiotherapy department in an academic teaching hospital. Participants: Participants with CLBP were randomly assigned to a walking program (n=20; mean age ± SD, 46.4±13.8y), supervised exercise class (n=20; mean age ± SD, 41.3±11.9y), or usual physiotherapy (n=20; mean age ± SD, 47.1±14.3y). The 3-month evaluation was completed by 44 participants (73%), and 42 (70%) participants completed the 6-month evaluation. Interventions: Participants received a physiotherapy-delivered 8-week walking program, an 8-week group supervised exercise class (1 class/wk), or 1-to-1 usual physiotherapy (advice, manual therapy, and exercise). Main Outcome Measures: Sleep was assessed by the self-reported Pittsburgh Sleep Quality Index (PSQI), Insomnia Severity Index (ISI), Pittsburgh Sleep Diary, and objective actigraphy. Results: Groups were comparable at baseline. Most (95%, n=57) of the participants had sleep disturbance. The acceptability of actigraphy was excellent at baseline (58 of 60 participants), but dropped at 3 months (26 of 44 participants). There were improvements on the PSQI and ISI in all groups at 3 and 6 months, with predominantly medium effect sizes (Cohen d=0.2-0.5). Conclusions: The high prevalence of sleep disturbance indicated the feasibility of good recruitment in future trials. The PSQI would be a suitable screening tool and outcome measure alongside an objective nonobtrusive sleep outcome measure. The effectiveness of physiotherapy for sleep disturbance in CLBP warrants investigation in a fully powered randomized controlled trial. © 2013 American Congress of Rehabilitation Medicine.

Water Content Determinations for Peat and Other Organic Soils Using the Oven-Drying Method

There has been much debate in the literature over the past 60 years regarding an appropriate oven-drying temperature for water content determinations in peat and other organic soils. For inorganic soils, the water content is usually based on the equilibrium dry mass corresponding to drying temperatures in the range 100-110°C. However, for peat and other organic soils, several researchers have recommended lower drying temperatures in the range 60-90°C in an attempt to prevent possible charring, oxidation, and/or vaporization of substances other than pore water. However, all of the relevant water is not fully evaporated at too low a temperature, and because specimen dry mass is a function of drying temperature, the resulting water content values are lower than those determined for the temperature range 100-110°C. Experimental data reported in this article show that oven drying of peat and other organic soils at 100-110°C using either gravity-convection or forced-draft ovens is acceptable for routine water content determinations. Because a standardized oven temperature is desirable when correlating water content with other material properties, it is recommended that oven drying of peat and other organic soils be performed over temperature ranges of either 105-110°C or 105 ± 5°C, in line with standardized ranges for inorganic soils. © 2014 Copyright Taylor & Francis Group, LLC.

First development and characterisation of polyclonal and monoclonal antibodies to the emerging fresh water toxin cylindrospermopsin

As increasing incidences in the occurrence of cylindrospermopsin (CYN) appear, in addition to further research on its toxicological nature, improved rapid methods to detect this toxin are required. Antibody based assays are renowned for their ability to provide rapid, portable, simple to use tests. As yet however there are no publications outlining how an antibody to CYN can be produced. A range of chemical approaches was investigated to synthesise CYN immunogens for antibody production but failed to generate a response. Finally, a modified Mannich reaction for immunogen synthesis was employed to couple the toxin to two carrier proteins. Both protein conjugates were successfully used to raise both polyclonal and monoclonal antibodies of high sensitivity to CYN. These antibodies were characterised employing competitive indirect ELISA and an optical biosensor assay. By ELISA the sensitivity achieved ranged from 27 to 131. pg/mL and by SPR 4.4 to 11.1. ng/mL thus demonstrating that the selection of immunoassay platform is important for the detection level required by the end user for their application. Low cross-reactivity to the much less toxic metabolite deoxyCYN was observed. This is the first reported production of antibodies to this toxin. © 2013 Elsevier B.V.

Organic synthesis in the interstellar medium by low-energy carbon irradiation

We present a first principles molecular dynamics (FPMD) study of the interaction of low-energy neutral carbon projectiles with amorphous solid water clusters at 30 K. Reactions involving the carbon atom at an initial energy of 11 and 1.7 eV with 30-molecule clusters have been investigated. Simulations indicate that the formation of hydroxymethylene, an intermediate in formaldehyde production, dominates at the higher energy. The reaction proceeds by fragmenting a water molecule, binding the carbon to the OH radical, and saturating the C valence with a hydrogen atom that can arise from the originally dissociated water molecule, or through a chain of proton transfer events. We identified several possible pathways for the formation of HCOH. When the initial collision occurs at the periphery of the cluster, we observe the formation of CO and the evaporation of water molecules. At the lower energy water fragmentation is not favorable, thus leading to the formation of weakly bound carbon-water complexes. © 2013 American Chemical Society.

Water spray cooling of polymers

The cooling process in conventional rotomolding is relatively long due to poor thermal conductivity of plastics. The lack of internal cooling is a major limitation although rapid external cooling is possible. Various internal cooling methodologies have been studied to reduce the cycle time. These include the use of compressed air, cryogenic liquid nitrogen, chilled water coils, and cryogenic liquid carbon dioxide, all of which have limitations. However, this article demonstrates the use of water spray cooling of polymers as a viable and effective method for internal cooling in rotomolding. To this end, hydraulic, pneumatic, and ultrasonic nozzles were applied and evaluated using a specially constructed test rig to assess their efficiency. The effects of nozzle type and different parametric settings on water droplet size, velocity, and mass flow rate were analyzed and their influence on cooling rate, surface quality, and morphology of polymer exposed to spray cooling were characterized. The pneumatic nozzle provided highest average cooling rate while the hydraulic nozzle gave lowest average cooling rate. The ultrasonic nozzle with medium droplet size traveling at low velocity produced satisfactory surface finish. Water spray cooling produced smaller spherulites compared to ambient cooling whilst increasing the cooling rate decreases the percentage crystallinity. © 2011 Society of Plastics Engineers Copyright © 2011 Society of Plastics Engineers.

Irradiation of water ice by C+ ions in the cosmic environment

We present a first principles molecular dynamics (FPMD) study of the interaction of low energy, positively charged, carbon (C+) projectiles with amorphous solid water clusters at 30 K. Reactions involving the carbon ion at an initial energy of 11 eV and 1.7 eV with 30-molecule clusters have been investigated. Simulations indicate that the neutral isoformyl radical, COH, and carbon monoxide, CO, are the dominant products of these reactions. All these reactions are accompanied by the transfer of a proton from the reacting water molecule to the ice, where it forms a hydronium ion. We find that COH is formed either via a direct, "knock-out", mechanism following the impact of the C+ projectile upon a water molecule or by creation of a COH_2^+ intermediate. The direct mechanism is more prominent at higher energies. CO is generally produced following the dissociation of COH. More frequent production of the formyl radical, HCO, is observed here than in gas phase calculations. A less commonly occurring product is the dihydroxymethyl, CH(OH)_2, radical. Although a minor result, its existence gives an indication of the increasing chemical complexity which is possible in such heterogeneous environments.

Electron-induced hydrogen loss in uracil in a water cluster environment

Low-energy electron-impact hydrogen loss due to dissociative electron attachment (DEA) to the uracil and thymine molecules in a water cluster environment is investigated theoretically. Only the A'-resonance contribution, describing the near-threshold behavior of DEA, is incorporated. Calculations are based on the nonlocal complex potential theory and the multiple scattering theory, and are performed for a model target with basic properties of uracil and thymine, surrounded by five water molecules. The DEA cross section is strongly enhanced when the attaching molecule is embedded in a water cluster. This growth is due to two effects: the increase of the resonance lifetime and the negative shift in the resonance position due to interaction of the intermediate negative ion with the surrounding water molecules. A similar effect was earlier found in DEA to chlorofluorocarbons. 

The impacts of replacing air bubbles with microspheres for the clarification of algae from low cell-density culture

Dissolved Air Flotation (DAF) is a well-known coagulation-flotation system applied at large scale for microalgae harvesting. Compared to conventional harvesting technologies DAF allows high cell recovery at lower energy demand. By replacing microbubbles with microspheres, the innovative Ballasted Dissolved Air Flotation (BDAF) technique has been reported to achieve the same algae cell removal efficiency, while saving up to 80% of the energy required for the conventional DAF unit. Using three different algae cultures (Scenedesmus obliquus, Chlorella vulgaris and Arthrospira maxima), the present work investigated the practical, economic and environmental advantages of the BDAF system compared to the DAF system. 99% cells separation was achieved with both systems, nevertheless, the BDAF technology allowed up to 95% coagulant reduction depending on the algae species and the pH conditions adopted. In terms of floc structure and strength, the inclusion of microspheres in the algae floc generated a looser aggregate, showing a more compact structure within single cell alga, than large and filamentous cells. Overall, BDAF appeared to be a more reliable and sustainable harvesting system than DAF, as it allowed equal cells recovery reducing energy inputs, coagulant demand and carbon emissions. © 2014 Elsevier Ltd.