Preliminary Results of a Prospective Randomized Trial of Restrictive Versus Standard Fluid Regime in Elective Open Abdominal Aortic Aneurysm Repair

Background: Open abdominal aortic aneurysm (AAA) repair is associated with a significant morbidity (primarily respiratory and cardiac complications) and an overall mortality rate of 4% to 10%. We tested the hypothesis that perioperative fluid restriction would reduce complications and improve outcome after elective open AAA repair.

A randomised, controlled trial of conventional versus automated weaning from mechanical ventilation using SmartcareTM/PS

Objective
Preliminary assessment of an automated weaning system (SmartCare™/PS) compared to usual management of weaning from mechanical ventilation performed in the absence of formal protocols.


Design and setting
A randomised, controlled pilot study in one Australian intensive care unit.


Patients
A total of 102 patients were equally divided between SmartCare/PS and Control.

Interventions
The automated system titrated pressure support, conducted a spontaneous breathing trial and provided notification of success (“separation potential”).

Measurements and results
The median time from the first identified point of suitability for weaning commencement to the state of “separation potential” using SmartCare/PS was 20 h (interquartile range, IQR, 2–40) compared to 8 h (IQR 2–43) with Control (log-rank P = 0.3). The median time to successful extubation was 43 h (IQR 6–169) using SmartCare/PS and 40 (14–87) with Control (log-rank P = 0.6). Unadjusted, the estimated probability of reaching “separation potential” was 21% lower (95% CI, 48% lower to 20% greater) with SmartCare/PS compared to Control. Adjusted for other covariates (age, gender, APACHE II, SOFAmax, neuromuscular blockade, corticosteroids, coma and elevated blood glucose), these estimates were 31% lower (95% CI, 56% lower to 9% greater) with SmartCare/PS. The study groups showed comparable rates of reintubation, non-invasive ventilation post-extubation, tracheostomy, sedation, neuromuscular blockade and use of corticosteroids.

Conclusions
Substantial reductions in weaning duration previously demonstrated were not confirmed when the SmartCare/PS system was compared to weaning managed by experienced critical care specialty nurses, using a 1:1 nurse-to-patient ratio. The effect of SmartCare/PS may be influenced by the local clinical organisational context.

Electronic cell counting to measure total cell numbers in bronchoalveolar lavage fluid

Cell counting of bronchoalveolar lavage (BAL) fluid is performed manually in routine practice. This has both methodological and inherent errors; however, the accuracy and suitability of automated counting devices have been questioned. In this study, a Coulter(R) Counter D Industrial model was calibrated and then used to measure the total cell count in unprocessed bronchoalveolar lavage fluid, and compared to a standard manual method.

Efficacy of a standard meticillin-resistant Staphylococcus aureus decolonisation protocol in routine clinical practice

Summary

Decolonisation may reduce the risk of meticillin-resistant Staphylococcus aureus (MRSA) infection in individual carriers and prevent transmission to other patients. The aims of this prospective cohort study were to determine the long-term efficacy of a standardised decolonisation regimen and to identify factors associated with failure. Patients colonised with MRSA underwent decolonisation, which was considered to be successful if there was no growth in three consecutive sets of site-specific screening swabs obtained weekly post treatment. If patients were successfully decolonised, follow-up cultures were performed 6 and 12 months later. Of 137 patients enrolled, 79 (58%) were successfully decolonised. Of these 79, 53 (67%) and 44 (56%) remained decolonised at 6 and 12 months respectively. Therefore only 44/137 (32%) patients who completed decolonisation were MRSA negative 12 months later. Outcome was not associated with a particular strain of MRSA. Successful decolonisation was less likely in patients colonised with a mupirocin-resistant isolate (adjusted odds ratio: 0.08; 95% confidence interval: 0.02–0.30), in patients with throat colonisation (0.22; 0.07–0.68) and in patients aged >80 years (0.30; 0.10–0.93) compared with those aged 60–80 years. These findings suggest that although initially successful in some cases, the protocol used did not result in long-term clearance of MRSA carriage for most patients.

DISTORTION MAPS FROM PREFERENTIAL HYPERACUITY PERIMETRY ARE HELPFUL IN MONITORING FUNCTIONAL RESPONSE TO LUCENTIS THERAPY

Purpose: To use preferential hyperacuity perimetry to obtain a quantitative measure of central visual field distortion that would aid in the monitoring of functional responsiveness to ranibizumab treatment.

Reconfigurable system-on-a-chip motion estimation architecture for multi-standard video coding

A new domain-specific, reconfigurable system-on-a-chip (SoC) architecture is proposed for video motion estimation. This has been designed to cover most of the common block-based video coding standards, including MPEG-2, MPEG-4, H.264, WMV-9 and AVS. The architecture exhibits simple control, high throughput and relatively low hardware cost when compared with existing circuits. It can also easily handle flexible search ranges without any increase in silicon area and can be configured prior to the start of the motion estimation process for a specific standard. The computational rates achieved make the circuit suitable for high-end video processing applications, such as HDTV. Silicon design studies indicate that circuits based on this approach incur only a relatively small penalty in terms of power dissipation and silicon area when compared with implementations for specific standards. Indeed, the cost/performance achieved exceeds that of existing but specific solutions and greatly exceeds that of general purpose field programmable gate array (FPGA) designs.

Automated mixed dimensional modelling from 2D and 3D CAD models

The motivation for this paper is to present procedures for automatically creating idealised finite element models from the 3D CAD solid geometry of a component. The procedures produce an accurate and efficient analysis model with little effort on the part of the user. The technique is applicable to thin walled components with local complex features and automatically creates analysis models where 3D elements representing the complex regions in the component are embedded in an efficient shell mesh representing the mid-faces of the thin sheet regions. As the resulting models contain elements of more than one dimension, they are referred to as mixed dimensional models. Although these models are computationally more expensive than some of the idealisation techniques currently employed in industry, they do allow the structural behaviour of the model to be analysed more accurately, which is essential if appropriate design decisions are to be made. Also, using these procedures, analysis models can be created automatically whereas the current idealisation techniques are mostly manual, have long preparation times, and are based on engineering judgement. In the paper the idealisation approach is first applied to 2D models that are used to approximate axisymmetric components for analysis. For these models 2D elements representing the complex regions are embedded in a 1D mesh representing the midline of the cross section of the thin sheet regions. Also discussed is the coupling, which is necessary to link the elements of different dimensionality together. Analysis results from a 3D mixed dimensional model created using the techniques in this paper are compared to those from a stiffened shell model and a 3D solid model to demonstrate the improved accuracy of the new approach. At the end of the paper a quantitative analysis of the reduction in computational cost due to shell meshing thin sheet regions demonstrates that the reduction in degrees of freedom is proportional to the square of the aspect ratio of the region, and for long slender solids, the reduction can be proportional to the aspect ratio of the region if appropriate meshing algorithms are used.