Factorial Design of Modelling Mix Proportion Parameters of Underwater Composite Cement Grouts

There is an increasing need to identify the rheological properties of cement grout using a simple test to determine the fluidity, and other properties of underwater applications such as washout resistance and compressive strength. This paper reviews statistical models developed using a factorial design that was carried out to model the influence of key parameters on properties affecting the performance of underwater cement grout. Such responses of fluidity included minislump and flow time measured by Marsh cone, washout resistance, unit weight, and compressive strength. The models are valid for mixes with 0.35–0.55 water-to-binder ratio (W/B), 0.053–0.141% of antiwashout admixture (AWA), by mass of water, and 0.4–1.8% (dry extract) of superplasticizer (SP), by mass of binder. Two types of underwater grout were tested: the first one made with cement and the second one made with 20% of pulverised fuel ash (PFA) replacement, by mass of binder. Also presented are the derived models that enable the identification of underlying primary factors and their interactions that influence the modelled responses of underwater cement grout. Such parameters can be useful to reduce the test protocol needed for proportioning of underwater cement grout. This paper attempts also to demonstrate the usefulness of the models to better understand trade-offs between parameters and compare the responses obtained from the various test methods that are highlighted.

The Role of Process Parameters in Determining Wall Thickness Distribution in Plug-Assisted Thermoforming

This article describes the results of a comprehensive investigation to determine the link between process parameters and observed wall thickness output for the plug-assisted thermoforming process. The overall objective of the work was to systematically investigate the process parameters that may be adjusted during production to control the wall thickness distribution of parts manufactured by plug-assisted thermoforming. The parameters investigated were the sheet temperature, plug temperature, plug speed, plug displacement, plug shape, and air pressure. As well as quantifying the effects of each parameter on the wall thickness distribution, a further aim of the work was to improve the understanding of the physical mechanisms of deformation of the sheet during the different stages of the process. The process parameters shown to have the greatest effect on experimentally determined wall thickness distribution were the plug displacement, sheet temperature, plug temperature, and plug shape. It is proposed that during the plug-assisted thermoforming of polystyrene the temperature dependent friction between the plug and sheet surface was the most important factor in determining product wall thickness distribution, whereas heat transfer was shown to play a less important role. POLYM. ENG. SCI., 2010. © 2010 Society of Plastics Engineers

Influence of post-calving regrouping strategy on welfare and performance parameters in dairy heifers

Thirty-six Holstein Friesian heifers (dairy herd replacements) were assigned to one of three regrouping treatments during the post-calving period. In Treatment 1, heifers were introduced individually to an established group of cows and heifers within 24 h of calving ('Single-day 1'). In Treatment 2, heifers were housed individually in a straw pen for I week after calving before being added individually to the group ('Single-day 7'). In Treatment 3, two heifers were housed together in a straw pen for 1 week after calving before being added as a pair to the group ('Pair-day T). The size of the resident group remained constant at 16 animals (10 mature cows and 6 first-lactation heifers). The behaviour of the heifers was assessed during their first 8 h and first month in the resident group, and milk yield parameters, body condition loss and live weight loss were assessed during the first month post-calving. Reproductive performance was assessed during the post-calving period, and hoof health parameters were measured I month prior to calving, and at I and 3 months post-calving. Heifers in the 'Pair-day 7' treatment appeared to associate closely during their first month in the group by spending more time than expected in the same pen area and in adjacent cubicles (P

Influence of regrouping strategy on performance, behaviour and carcass parameters in pigs

One thousand two hundred pigs were weaned at 4 weeks of age and mixed to form groups of ten animals that were balanced for gender. The groups consisted of uniform weight groups (i.e. separate groups of small, medium or large pigs), or mixed weight groups (i.e. groups containing small, medium and large pigs). Half of the groups were retained from weaning until slaughter at 21 weeks of age, and half were regrouped at the start of the finishing period at 10 weeks of age. In this regrouping, uniform weight groups were regrouped to form mixed weight groups, and mixed weight groups were regrouped to form uniform weight groups. In addition, some mixed weight groups were regrouped to form mixed weight groups in order to assess the effect of regrouping at 10 weeks of age on performance and aggressive behaviour.

Effects of breed and production system on lameness parameters in dairy cattle

The aim of the present study was to assess the effects of Holstein-Friesian (HF) and Norwegian (N) dairy cattle genotypes on lameness parameters in dairy cattle within different production systems over the first 2 lactations. Following calving, HF (n = 39) and N (n = 45) heifers were allocated to 1 of 3 systems of production (high level of concentrate, low level of concentrate, and grass-based). High-and low-concentrate animals were continuously housed indoors on a rotational system so that they spent similar amounts of time on slatted and solid concrete floors. Animals on the grass treatment grazed from spring to autumn in both years of the study, so that most animals on this treatment grazed from around peak to late lactation. Claw health was recorded in both hind claws of each animal at 4 observation periods during each lactation as follows: 1) -8 to 70 d postcalving, 2) 71 to 150 d postcalving, 3) 151 to 225 d postcalving, and 4) 226 to 364 d postcalving. Sole lesions, heel erosion, axial wall deviation, sole length of the right lateral hind claw (claw length), right heel width, and right lateral hind heel height were recorded as well as the presence of digital dermatitis. The N cows had lower (better) white line and total lesion scores than HF cows. Cows on the high-and low-concentrate treatments had better sole and total lesion scores than cows on the grass treatment. The HF cows had better locomotion scores than N cows. Breed and production system differences were observed with respect to claw conformation, including claw length, heel width, and heel height. Digital dermatitis was associated with worse sole lesion scores and interacted with production system to influence white line lesion scores and maximum heel erosion scores. This study shows that genetic, environmental, and infectious factors are associated with hoof pathologies in dairy cows.

Influence of environmental enrichment on welfare-related behavioural and physiological parameters in growing pigs

Three hundred and twenty pigs were reared from birth to slaughter at 21 weeks in either barren or enriched environments. The barren environments were defined as intensive housing (slatted floors and minimum recommended space allowances) and the enriched environments incorporated extra space including an area which contained peat and straw in a rack. Behavioural observations showed that environmental enrichment reduced time spent inactive and rime spent involved in harmful social and aggressive behaviour (P

Atmospheric parameters and rotational velocities for a sample of Galactic B-type supergiants

High-resolution optical spectra of 57 Galactic B-type supergiant stars have been analysed to determine their rotational and macroturbulent velocities. In addition, their atmospheric parameters (effective temperature, surface gravity and microturbulent velocity) and surface nitrogen abundances have been estimated using a non-local thermodynamic equilibrium grid of model atmospheres. Comparisons of the projected rotational velocities have been made with the predictions of stellar evolutionary models and in general good agreement was found. However, for a small number of targets, their observed rotational velocities were significantly larger than predicted, although their nitrogen abundances were consistent with the rest of the sample. We conclude that binarity may have played a role in generating their large rotational velocities. No correlation was found between nitrogen abundances and the current projected rotational velocities. However, a correlation was found with the inferred projected rotational velocities of the main-sequence precursors of our supergiant sample. This correlation is again in agreement with the predictions of single star evolutionary models that incorporate rotational mixing. The origin of the macroturbulence and microturbulent velocity fields is discussed and our results support previous theoretical studies that link the former to subphotospheric convection and the latter to non-radial gravity mode oscillations. In addition, we have attempted to identify differential rotation in our most rapidly rotating targets.

Investigation of swelling and network parameters of poly (ethylene glycol)-crosslinked poly (methyl vinyl ether-co-maleic acid) hydrogels

he influence of poly(ethylene glycol) (PEG) plasticiser content and molecular weight on the physicochemical properties of films cast from aqueous blends of poly(methyl vinyl ether-co-maleic acid) was investigated using thermal analysis, swelling studies, scanning electron microscopy (SEM) and attenuated total reflectance (ATR)-Fourier transform infrared (FTIR) spectroscopy. FTIR spectroscopy revealed a shift of the CO peak from 1708 to 1731 cm-1, indicating that an esterification reaction had occurred upon heating, thus producing crosslinked films. Higher molecular weight PEGs (10,000 and 1000 Da, respectively), having greater chain length, producing hydrogel networks with lower crosslink densities and higher average molecular weight between two consecutive crosslinks. Accordingly, such materials exhibited higher swelling rates. Hydrogels crosslinked with a low molecular weight PEG (PEG 200) showed rigid networks with high crosslink densities and, therefore, lower swelling rates. Polymer:plasticizer ratio alteration did not yield any discernable patterns, regardless of the method of analysis. The polymer–water interaction parameter (?) increased with increases in the crosslink density. SEM studies showed that porosity of the crosslinked films increased with increasing PEG MW, confirming what had been observed with swelling studies and thermal analysis, that the crosslink density must be decreased as the Mw of the crosslinker is increased. Hydrogels containing PMVE/MA/PEG 10,000 could be used for rapid delivery of drug, due to their low crosslink density. Moderately crosslinked PMVE/MA/PEG 1000 hydrogels or highly crosslinked PMVE/MA/PEG 200 systems could then be used in controlling the drug delivery rates. We are currently evaluating these systems, both alone and in combination, for use in sustained release drug delivery devices.