FACTORIAL EXPERIMENTAL-DESIGN FOR CONCRETE DURABILITY RESEARCH

It is widely accepted that concrete designed to perform satisfactorily in adverse environmental conditions must have a high cement content and a low water-cement ratio. In addition, in order to enhance its durability, many types of additive and admixture such as super-plasticizers, fly ash, silica fume, ggbfs, etc., have been used in the past. However, a close study of the published literature indicates that the effect of mix variables on the durability and the interaction between the various ingredients are not fully understood. Some of these apparent contradictions are due to the limitations in the design of the experimental programme. For instance, it is evident that relatively higher concentrations of aggregates increase the tortuosity of the flow path and hence reduce the permeability, which results in an improvement in the durability. Therefore, an increase in cement content without a proportional decrease in water-cement ratio may reduce the durability. In such cases, the interactive effects of factors can be established by resorting to a properly designed experimental programme, such as the factorial experimental design.

Effect of Carbon Reduction on the Toughness of 9CrWVTaN Steels

Nitride-strengthened, reduced activation, martensitic steel is anticipated to have higher creep strength because of the remarkable thermal stability of nitrides. Two nitride-strengthened, reduced activation martensitic steels with different carbon contents were prepared to investigate the microstructure and mechanical property changes with decreasing carbon content. It has been found that both steels had the microstructure of full martensite with fine nitrides dispersed homogeneously in the matrix and displayed extremely high strength but poor toughness. Compared with the steel with low carbon content (0.005 pct in wt pct), the steel with high carbon content (0.012 pct in wt pct) had not only the higher strength but also the higher impact toughness and grain coarsening temperature, which was related to the carbon content. On the one hand, carbon reduction led to Ta-rich inclusions; on the other hand, the grain grew larger when normalized at high temperature because of the absence of Ta carbonitrides, which would decrease impact toughness. The complicated Al2O3 inclusions in the two steels have been revealed to be responsible for the initiated cleavage fracture by acting as the critical cracks.

Relationship between electrical resistivity and basic geotechnical parameters for marine clays

Recently, considerable efforts have been made in the attempt to map quick clay areas using electrical resistivity measurements. However there is a lack of understanding regarding which soil parameters control the measured resistivity values. To address this issue, inverted resistivity values from 15 marine clay sites in Norway have been compared with basic geotechnical index properties. It was found that the resistivity value is strongly controlled by the salt content of the pore fluid. Resistivity decreases rapidly with increasing salt content. There is also a relatively clear trend of decreasing resistivity with increasing clay content and plasticity index. Resistivity values become very low (˜5 O·m) for high clay content (>50%), medium- to high-plasticity (Ip ˜ 20%) materials with salt content values greater than about 8 g/L (or corresponding remoulded shear strength values greater than 4 kPa). For the range of values studied, there is poor correlation between resistivity and bulk density and between resistivity and water content. The data studied suggest that the range of resistivity values corresponding to quick clay is 10 to 100 O·m, which is consistent with other published limits. A comparison is made between two-dimensional electrical resistivity tomography (ERT) and resistivity cone penetration test (RCPTU) data for two of the sites and the two sets of data show similar trends and values irrespective of scale effect.

Comparison of a plant based natural surfactant with SDS for washing of As(V) from Fe rich soil

This study explores the possible application of a biodegradable plant based surfactant, obtained from Sapindus mukorossi, for washing low levels of arsenic (As) from an iron (Fe) rich soil. Natural association of As(V) with Fe(III) makes the process difficult. Soapnut solution was compared to anionic surfactant sodium dodecyl sulfate (SDS) in down-flow and a newly introduced suction mode for soil
column washing. It was observed that soapnut attained up to 86% efficiency with respect to SDS in removing As. Full factorial design of experiment revealed a very good fit of data. The suction mode generated up to 83 kPa pressure inside column whilst down-flow mode generated a much higher pressure of 214 kPa, thus making the suction mode more efficient. Micellar solubilisation was found to
be responsible for As desorption from the soil and it followed 1st order kinetics. Desorption rate coefficient of suction mode was found to be in the range of 0.005 to 0.01, much higher than down-flow mode values. Analysis of the FT-IR data suggested that the soapnut solution did not interact chemically with As, offering an option for reusing the surfactant. Soapnut can be considered as a soil washing
agent for removing As even from soil with high Fe content.

Adsorption of aqueous metal ions on oxygen and nitrogen functionalized nanoporous activated carbons

In this study, the adsorption characteristics of two series of oxygen and nitrogen functionalized activated carbons were investigated. These series were a low nitrogen content(similar to 1 wt % daf) carbon series derived from coconut shell and a high nitrogen content (similar to 8 wt % daf) carbon series derived from polyacrylonitrile. In both series, the oxygen contents were varied over the range similar to 2-22 wt % daf. The porous structures of the functionalized activated carbons were characterized using N-2 (77 K) and CO2 (273 K) adsorption. Only minor changes in the porous structure were observed in both series. This allowed the effect of changes in functional group concentrations on metal ion adsorption to be studied without major influences due to differences in porous structure characteristics. The surface group characteristics were examined by Fourier transform infrared (FTIR) spectroscopy, acid/base titrations, and measurement of the point of zero charge (pH(PZC)). The adsorption of aqueous metal ion species, M2+(aq), on acidic oxygen functional group sites mainly involves an ion exchange mechanism. The ratios of protons displaced to the amount of M2+(aq) metal species adsorbed have a linear relationship for the carbons with pH(PZC) <= 4.15. Hydrolysis of metal species in solution may affect the adsorption of metal ion species and displacement of protons. In the case of basic carbons, both protons and metal ions are adsorbed on the carbons. The complex nature of competitive adsorption between the proton and metal ion species and the amphoteric character of carbon surfaces are discussed in relation to the mechanism of adsorption.

Adsorption of metal ions on nitrogen surface functional groups in activated carbons

A commercially available coconut-shell-derived active carbon was oxidized with nitric acid, and both the original and oxidized active carbons were treated with ammonia at 1073 K to incorporate nitrogen functional groups into the carbon. An active carbon with very high nitrogen content (similar to9.4 wt % daf) was also prepared from a nitrogen-rich precursor, polyacrylonitrile (PAN). These nitrogen-rich carbons had points of zero charge (pH(pzc)) similar to H-type active carbons. X-ray absorption near-edge structure (XANES) spectroscopy, Fourier transform infrared (FTIR) spectroscopy, and temperature-programmed desorption (TPD) were used to characterize the nitrogen functional groups in the carbons. The nitrogen functional groups present on the carbon surface were pyridinic, pyrrolic (or indolic), and pyridonic structures. The adsorption of transition metal cations Cd2+, Ni2+, and Cu2+ from aqueous solution on the suite of active carbons showed that adsorption was markedly higher for carbons with nitrogen functional groups present on the surface than for carbons with similar pH(pzc) values. In contrast, the adsorption characteristics of Ca2+ from aqueous solution were similar for all the carbons studied. Flow microcalorimetry (FMC) studies showed that the enthalpies of adsorption of Cd2+(aq) on the active carbons with high nitrogen contents were much higher than for nitric acid oxidized carbons studied previously, which also had enhanced adsorption characteristics for metal ion species. The enthalpies of adsorption of Cu2+ were similar to those obtained for Cd2+ for specific active carbons. The nitrogen functional groups in the carbons act as surface coordination sites for the adsorption of transition metal ions from aqueous solution. The adsorption characteristics of these carbons are compared with those of oxidized carbons.

Coherent synchrotron emission from electron nanobunches formed in relativistic laser-plasma interactions

Extreme ultraviolet (XUV) and X-ray harmonic spectra produced by intense laser-solid interactions have, so far, been consistent with Doppler upshifted reflection from collective relativistic plasma oscillations-the relativistically oscillating mirror mechanism(1-6). Recent theoretical work, however, has identified a new interaction regime in which dense electron nanobunches are formed at the plasma-vacuum boundary resulting in coherent XUV radiation by coherent synchrotron emission(7,8) (CSE). Our experiments enable the isolation of CSE from competing processes, demonstrating that electron nanobunch formation does indeed occur. We observe spectra with the characteristic spectral signature of CSE-a slow decay of intensity, I, with high-harmonic order, n, as I(n) proportional to n(-1.62) before a rapid efficiency rollover. Particle-in-cell code simulations reveal how dense nanobunches of electrons are periodically formed and accelerated during normal-incidence interactions with ultrathin foils and result in CSE in the transmitted direction. This observation of CSE presents a route to high-energy XUV pulses(7,8) and offers a new window on understanding ultrafast energy coupling during intense laser-solid density interactions.

Blueberries decrease cardiovascular risk factors in obese men and women with metabolic syndrome

Among all fruits, berries have shown substantial cardio-protective benefits due to their high polyphenol content. However, investigation of their efficacy in improving features of metabolic syndrome and related cardiovascular risk factors in obesity is limited. We examined the effects of blueberry supplementation on features of metabolic syndrome, lipid peroxidation, and inflammation in obese men and women. Forty-eight participants with metabolic syndrome [4 males and 44 females; BMI: 37.8 +/- 2.3 kg/m(2); age: 50.0 +/- 3.0 y (mean +/- SE)] consumed freeze-dried blueberry beverage (50 g freeze-dried blueberries, approximately 350 g fresh blueberries) or equivalent amounts of fluids (controls, 960 mL water) daily for 8 wk in a randomized controlled trial. Anthropometric and blood pressure measurements, assessment of dietary intakes, and fasting blood draws were conducted at screening and at wk 4 and 8 of the study. The decreases in systolic and diastolic blood pressures were greater in the blueberry-supplemented group (- 6 and - 4%, respectively) than in controls (- 1.5 and - 1.2%) (P lt 0.05), whereas the serum glucose concentration and lipid profiles were not affected. The decreases in plasma oxidized LDL and serum malondialdehyde and hydroxynonenal concentrations were greater in the blueberry group (- 28 and - 17%, respectively) than in the control group (- 9 and - 9%) (P lt 0.01). Our study shows blueberries may improve selected features of metabolic syndrome and related cardiovascular risk factors at dietary achievable doses.

Galactose Metabolism in Saccharomyces cerevisiae

Galactose is metabolised to the more metabolically useful glucose 6-phosphate by the enzymes of the Leloir pathway. This pathway is necessary as the initial enzymes of glycolysis are unable to recognise galactose. In most organisms, including Saccharomyces cerevisiae, five enzymes are required to catalyse the conversion: galactose mutarotase, galactokinase, galactose 1-phosphate uridyltransferase, UDP-galactose 4-epimerase and phosphoglucomutase. The pathway has attracted interest in S. cerevisiae as it is under very strict genetic control and thus provides an excellent model for the study of gene expression in eukaryotes. In the presence of glucose the genes encoding the Leloir pathway enzymes (the GAL genes) are completely repressed through the action of a transcription factor Mig1p. Only in the presence of galactose and the absence of glucose do the concerted actions of Gal4p, Gal80p and Gal3p enable the rapid and high level activation of the GAL genes. The exact mechanism of action of these three proteins is controversial. Galactose metabolism in S. cerevisiae is also of interest because it can be exploited both in the laboratory (for high level expression of heterologous proteins and in the yeast two hybrid screen) and industrially (increasing flux through the Leloir pathway in order to make more efficient use of feedstocks with high galactose content). Recent work on the structures of the various proteins, their mechanisms of action and attempts to gain an integrated understanding of transcriptional and metabolic events will assist our understanding of both the fundamental biochemical processes and how these might be exploited commercially.

Investigation of failures in Irish raised bogs

This paper presents the results of field geophysical testing and laboratory testing of peat from Carn Park and Roosky raised bogs in the Irish Midlands. The motivation for the work was highlight the importance of these areas and to begin to attempt to understand the reasons for the failure of the bogs despite them having surface slopes of some 1°. It was found that the peat is typical of that of Irish raised bogs being up to 8m thick towards the “high” dome of the bogs. The peat is characterised by low density, high water content, high organic content, low undrained shear strength and high compressibility. The peat is also relatively permeable at in situ stress. Geophysical electrical resistivity tomography and ground penetrating radar data shows a clear thinning of the peat in the area of the failures corresponding to a reduction in volume from dewatering by edge drains/peat harvesting. This finding is supported by detailed water content measurements. It was also shown that the peat base topography is relatively flat and indicates that the observed surface movement has come from within the peat rather than from the material below the peat. Potential causes of the failures include conventional slope instability, the effect of seepage forces or the release of built-up gas in the peat mass. Further measurements are required in order to study these in more detail.

Arsenic Bioaccessibility in Cooked Rice as Affected by Arsenic in Cooking Water

Rice can easily accumulate arsenic (As) into its grain and is known to be the highest As-containing cereal. In addition, the As burden in rice may increase during its processing (such as when cooking using As-polluted water). The health risk posed by the presence of As in cooked rice depends on its release from the matrix along the digestive system (bioaccessibility). Two types of white polished long-grain rice, namely, nonparboiled and parboiled (total As: 202 and 190 mu g As kg(-1), respectively), were cooked in excess of water with different levels of As (0, 10, 47, 222, and 450 mu g As L-1). The bioaccessibility of As from these cooked rice batches was evaluated with an in vitro dynamic digestion process. Rice cooked with water containing 0 and 10 mu g As L-1 showed lower As concentrations than the raw (uncooked) rice. However, cooking water with relatively high As content (>= 47 mu g As L-1) significantly increased the As concentration in the cooked rice up to 8- and 9-fold for the nonparboiled and parboiled rice, respectively. Parboiled rice, which is most widely consumed in South Asia, showed a higher percentage of As bioaccessibility (59% to 99%) than nonparboiled rice (36% to 69%) and most of the As bioaccessible in the cooked rice (80% to 99%) was released easily during the first 2 h of digestion. The estimation of the As intake through cooked rice based on the As bioaccessibility highlights that a few grams of cooked rice (less than 25 g dry weight per day) cooked with highly As contaminated water is equivalent to the amount of As from 2 L water containing the maximum permissible limit (10 mu g As L-1).

Range expansion and comparative habitat use of insular, congeneric lagomorphs: invasive European hares Lepus europaeus and endemic Irish hares Lepus timidus hibernicus

The European hare (Lepus europaeus) has declined throughout its native range but invaded numerous regions where it has negatively impacted native wildlife. In southern Sweden, it replaces the native mountain hare (L. timidus) through competition and hybridisation. We investigated temporal change in the invasive range of the European hare in Ireland, and compared its habitat use with the endemic Irish hare (L. timidus hibernicus). The range of the European hare was three times larger and its core range twice as large in 2012–2013 than in 2005. Its rate of radial range expansion was 0.73 km year−1 with its introduction estimated to have occurred ca. 1970. Both species utilised improved and rough grasslands and exhibited markedly similar regression coefficients with almost every land cover variable examined. Irish hares were associated with low fibre and high sugar content grass (good quality grazing) whilst the invader had a greater tolerance for low quality forage. European hares were associated with habitat patch edge density, suggesting it may be more suited to using hedgerows as diurnal resting sites than the Irish hare. Consequently, the invader had a wider niche breadth than the native but their niche overlap was virtually complete. Given the impact of the European hare on native species elsewhere, and its apparent pre-adaption for improved grasslands interspersed with arable land (a habitat that covers 70 % of Ireland), its establishment and range expansion poses a significant threat to the ecological security of the endemic Irish hare, particularly given their ecological similarities.

Distributed MPC for Frequency Regulation in Multi-Terminal HVDC Grids

High Voltage Direct Current (HVDC) lines allow large quantities of power to be
transferred between two points in an electrical power system. A Multi-Terminal HVDC (MTDC) grid consists of a meshed network of HVDC lines, and this allows energy reserves to be shared between a number of AC areas in an efficient manner. Secondary Frequency Control (SFC) algorithms return the frequencies in areas connected by AC or DC lines to their original setpoints after Primary Frequency Controllers have been called following a contingency. Where multiple
TSOs are responsible for different parts of a MTDC grid it may not be possible to implement SFC from a centralised location. Thus, in this paper a simple gain based distributed Model Predictive Control strategy is proposed for Secondary Frequency Control of MTDC grids which allows TSOs to cooperatively perform SFC without the need for centralised coordination.

Losses of bioactive polyacetylenes during minimal processing of carrots

Vegetables of the Apiaceae plant family such as carrots, parsnip, celery and parsley,contain in minor quantities, a group of bioactive aliphatic C17-polyacetylenes (falcarinol,falcarindiol, falcarindiol-3- acetate). Recent studies have highlighted important biologicalfunctions in vitro and in vivo (animal studies) although the beneficial effect in humannutrition attributable to an increased in polyacetylenes diet are yet to be confirmed(Lund, 1990).Carrots not only contain relatively high polyacetylene content but also form a significantpart of many countries dietary habits. Carrots are also present in some ready-to-eat foodssuch as chilled freshly prepared salads, as part of the increasingly popular minimallyprocessed foods. Whereas the effect of conventional processing (boiling, vacuum processing) on the levels of polyacetylenes has been relatively well studied, the effect of minimal mechanical operations such as “peeling”, “mechanical cutting” and “chlorine washing” remains unknown.

New design of a multi-jet target for quasi phase matching

An improved dual-gas quasi-phase matching (QPM) foil target for high harmonic generation (HHG) is presented. The target can be setup with 12 individual gas inlets each feeding multiple nozzles separated by a minimum distance of 10 μm. Three-dimensional gas density profiles of these jets were measured using a Mach-Zehnder Interferometer. These measurements reveal how the jets influence the density of gas in adjacent jets and how this leads to increased local gas densities. The analysis shows that the gas profiles of the jets are well defined up to a distance of about 300 μm from the orifice. This target design offers experimental flexibility, not only for HHG/QPM investigations, but also for a wide range of experiments due to the large number of possible jet configurations. We demonstrate the application to controlled phase tuning in the extreme ultraviolet using a 1 kHz-10 mJ-30 fs-laser system where interference between two jets in the spectral range from 17 to 30 nm was observed.