Ultra-thin tunable microwave absorber using liquid crystals

A dynamically adaptive radar absorber is described which is based on a periodic array of microstrip patches that are printed on a 500 mu m-thick liquid crystal substrate. The measured reflectivity of the structure is less than -38 dB with a 200 MHz -10 dB bandwidth at 10.19 GHz when a +4 DC bias is applied. It is shown that a 34 dB reduction in signal loss occurs when the bias voltage is increased to 20 V.

Dual-mode compact structure comprising of side-fed bifilar and quadrifilar helix antenna

A side-fed bifilar helix antenna can be integrated with a quadrifilar helix antenna in a piggy back configuration in order to achieve a dual-mode radiating structure. The overall length of the structure is 0.44 lambda at the resonant frequency (1.54 GHz) of the space mode antenna and 0.39 lambda at the resonant frequency (1.34 GHz) of the terrestrial mode antenna. The computed results are validated by experimental data.

Single feed low profile omnidirectional antenna with slant 45 degrees linear polarization

It is shown that a side-fed bifilar helix antenna with a single feed, can generate a slant 451 linearly polarized onmidirectional toroidal pattern. The antenna has a low profile and does not require a ground plane. The bifilar helix antenna provides slant 45 degrees polarization over a solid angle of almost 4 pi steradians as compared to a crossed dipole which generates a tilted 45 degrees linearly, polarized pattern only over a solid angle of 1.14 pi steradians. The computed results are validated by experimental data.

Polarisation independent bandpass FSS

The spectral transmittance of a frequency selective surface (FSS), which consists of two free-standing arrays of short-circuited nested annular slots, is presented. The FSS was designed to provide a minimum of 20 dB isolation between the frequency bands 316.5-325.5 and 349.5-358.5 GHz when the filter operates in the TE and TM planes at 45 degrees incidence. Experimental results, which are in close agreement with the computed transmission coefficients, show that the maximum insertion loss is 0.9 dB, and the minimum cross-polar discrimination is at least 21 dB in the passbands. The FSS yields virtually identical spectral responses in the two polarisation planes over the frequency range 315-359 GHz.

Liquid crystal tunable mm wave frequency selective surface

A frequency selective surface (FSS) which exploits the dielectric anisotropy of liquid crystals to generate an electronically tunable bandpass filter response at D Band (110-170 GHz) is presented. The device consists of two printed arrays of slot elements which are separated by a 130-mu m thick layer of liquid crystals. A 3% shift in the filter passband occurs when the substrate permittivity is increased by applying a control signal of 10 V. Measured results show that the insertion loss increases from -3.7 dB to -10.4 dB at resonance (134 GHz), thus demonstrating the potential to create a FSS which can be switched between a transmitting and a reflecting structure.

Single sideband FSS with high image rejection

The design of a quasi-optical single sideband filter, which provides more than 30 dB of isolation between the frequency bands 294-305.5 and 329.5-341.5 GHz in the TM plane at 45 degrees incidence, is described. The structure, which consists of three free-standing arrays of dipole slot elements, generates a bandpass spectral response with an insertion loss below 0.5 dB at resonance. Simulated and measured transmission coefficients in the range 250-400 GHz are shown to be in good agreement.

Tunable liquid crystal reflectarray patch element

Numerical and measured results are employed at X-band to demonstrate that the electrical properties ofnematic state liquid crystal can be exploited to produce phase shifters for beam scanning printed reflectarray antennas with a tunable range greater than 180'.

Element suitability for circularly polarised phase agile reflectarray applications

The electrical characteristics of various elements that can be used as spatial phase shifters in circularly polarised (CP) reflectarrays are contrasted. The elements investigated are; a single rotating dipole at 10.3 GHz; a multiple dipole at 18.2 GHz; a rotating stub at 2.8 GHz; and a periphery point short-circuited circular patch at 3.0 GHz. For each element type, results are presented for the reflection phase, polarisation purity and reflection loss. Where appropriate, experiments are performed using the waveguide simulator technique to validate the numerical EM simulation.

Concentric split ring element for dual frequency reflectarray antennas

The reflection phase response of a two-layer array of orthogonally oriented concentric split rings is presented. Splitting the ring elements suppresses the interlayer coupling and produces polarisation sensitive scattering. Simulated and measured results at X-band demonstrate that these proper-ties enable the reflection phase coefficients of a reflect-array to be independently optimised at two different frequencies.

Idealised operation of zero-voltage-switching series-L/parallel-tuned Class-E power amplifier

An analysis of a modified series-L/parallel-tuned Class-E power amplifier is presented, which includes the effects that a shunt capacitance placed across the switching device will have on Class-E behaviour. In the original series L/parallel-tuned topology in which the output transistor capacitance is not inherently included in the circuit, zero-current switching (ZCS) and zero-current derivative switching (ZCDS) conditions should be applied to obtain optimum Class-E operation. On the other hand, when the output transistor capacitance is incorporated in the circuit, i.e. in the modified series-L/parallel-tuned topology, the ZCS and ZCDS would not give optimum operation and therefore zero-voltage-switching (ZVS) and zero-voltage-derivative switching (ZVDS) conditions should be applied instead. In the modified series-L/parallel-tuned Class-E configuration, the output-device inductance and the output-device output capacitance, both of which can significantly affect the amplifier's performance at microwave frequencies, furnish part, if not all, of the series inductance L and the shunt capacitance COUT, respectively. Further, when compared with the classic shunt-C/series-tuned topology, the proposed Class-E configuration offers some advantages in terms of 44% higher maximum operating frequency (fMAX) and 4% higher power-output capability (PMAX). As in the classic topology, the fMAX of the proposed amplifier circuit is reached when the output-device output capacitance furnishes all of the capacitance COUT, for a given combination of frequency, output power and DC supply voltage. It is also shown that numerical simulations agree well with theoretical predictions.

Even order harmonic Series-L/Parallel-Tuned Class-E frequency multiplier

In this brief, we propose a new Class-E frequency multiplier based on the recently introduced Series-L/Parallel-Tuned Class-E amplifier. The proposed circuit produces even-order output harmonics. Unlike previously reported solutions the proposed circuit can operate under 50% duty ratio which minimizes the conduction losses. The circuit also offers the possibility for increased maximum operating frequency, reduced peak switch voltage, higher load resistance and inherent bond wire absorption; all potentially useful in monolithic microwave integrated circuit implementations. In addition, the circuit topology suggested large transistors with high output capacitances can be deployed. Theoretical design equations are given and the predictions made using these are shown to agree with harmonic balance circuit simulation results.

Design strategies for dual-band class-e power amplifier using composite right/left-handed transmission lines

In this article we propose a technique for dual-band Class-E power amplifier design using composite right/left-handed transmission lines, CRLH TLs. Design equations are presented and design procedures are elaborated. Because of the nonlinear phase dispersion characteristic of CRLH TLs, the single previous attempt at applying this method to dual bond Class-E amplifier design was not sufficient to simultaneously satisfy, the minimum requirement of Class-E impedances at both the fundamental and the second harmonic frequencies. This article rectifies this situation. A design example illustrating the synthesis procedure for a 0.5W-5V dual band Class-E amplifier circuit simultaneously operated at 900 MHz and 2.4 GHz is given and compared with ADS simulation.

Retro-transceiver array using monopole antennas

In this paper, we show how a self-tracking antenna array constructed using gimel /4 monopoles can be constructed, which is capable of receiving with gain over an entire 360 degrees azimuthal cut. It is also shown how the self-tacking receive unit can be used in conjunction with a self-phased transmitter so that self-steered spatially selective receive and transmit functions ran be formed simultaneously. The resulting array is capable of maintaining spatially selective receive and transmit functions to a roaming target without prior knowledge of its physical location.