Amplitude and Phase Controlled Reflectarray Element Based on an Impedance Transformation Unit

An architecture to simultaneously affect both amplitude and phase control from a reflectarray element using an impedance transformation unit is demonstrated. It is shown that a wide range of control is possible from a single element, removing the conventional necessity for variable sized elements across an array in order to form a desired reflectarray far-field pattern. Parallel plate waveguide measurements for a 2.2 GHz prototype element validate the phase and amplitude variation available from the element. It is demonstrated that there is sufficient control of the element's reflection response to allow Dolph-Tschebyscheff weighting coefficients for major-lobe to side-lobe ratios of up to 36 dB to be implemented.

325GHz Single Layer Sub-Millimeter Wave FSS Based Split Ring Linear to Circular Polarisation Convertor

A single layer, frequency selective surface based, sub-millimeter wave transmission polarizer is presented that converts incident slant linear 45° polarization into circular polarization upon transmission. The polarization convertor consists of a 30 mm diameter 10 thick silicon reinforced metalized screen containing 2700 resonator cells and perforated with nested split ring slot apertures. The screen was designed and optimized using CST Microwave Studio and predictions were validated experimentally by transmission measurements over the 250-365 GHz frequency range. This frequency range is used for remote environmental monitoring and 325 GHz represents a molecular emission line for H2O. The results obtained show good agreement between measured and modeled predictions. The measured 3 dB axial ratio bandwidth was 11.75%, measured minimum Axial Ratio was 0.19 dB and the measured insertion loss of the single layer screen was 3.38 dB

A commentary on climate change, stone decay dynamics and the ‘greening’ of natural stone buildings: new perspectives on ‘deep wetting’

Environmental controls on stone decay processes are rapidly changing as a result of changing climate. UKCP09 projections for the 2020s (2010–2039) indicate that over much of the UK seasonality of precipitation will increase. Summer dryness and winter wetness are both set to increase, the latter linked to projected precipitation increases in autumn and spring months. If so, this could increase the time that stone structures remain wet and possibly the depth of moisture penetration, and it appears that building stone in Northern Ireland has already responded through an increased incidence of algal ‘greening’.This paper highlights the need for understanding the effects of climate change through a series of studies of largely sandstone structures. Current and projected climatic trends are therefore considered to have aesthetic, physical and chemical implications that are not currently built into our models of sandstone decay, especially with respect to the role played by deep-seated wetness on sandstone deterioration and decay progression and the feedbacks associated with, for example surface algal growth. In particular,it is proposed that algal biofilms will aid moisture retention and further facilitate moisture and dissolved salt penetration to depth. Thus, whilst the outer surface of stone may continue to experience frequent wetting and drying associated with individual precipitation events, the latter is less likely to be complete, and the interiors of building blocks may only experience wetting/drying in response to seasonal cycling. A possible consequence of deeper salt penetration could be a delay in the onset of surface deterioration,but more rapid and effective retreat once it commences as decay mechanisms ‘tap into a reservoir of deep salt’.

Parametric FIR Design of Propagation Loss Filters in Digital Waveguide String Models

One of the attractive features of sound synthesis by physical modeling is the potential to build acoustic-sounding digital instruments that offer more flexibility and different options in its design and control than their real-life counterparts. In order to develop such virtual-acoustic instruments, the models they are based on need to be fully parametric, i.e., all coefficients employed in the model are functions of physical parameters that are controlled either online or at the (offline) design stage. In this letter we show how propagation losses can be parametrically incorporated in digital waveguide string models with the use of zero-phase FIR filters. Starting from the simplest possible design in the form of a three-tap FIR filter, a higher-order FIR strategy is presented and discussed within the perspective of string sound synthesis with digital waveguide models.

Crystal Creatures: Context for the Dublin Blaschka Congress

The ‘Dublin Blaschka Congress’ was conceived as a gathering to bring together the diverse scholarly disciplines that are uniquely, if eccentrically, joined in the study of scientific glass models. Leopold and Rudolf Blaschka are best known for the ‘Glass Flowers’ of Harvard but in the nineteenth century they also invented techniques to sculpt anatomically accurate marine invertebrates in glass. In the course of preparing the Congress and a coordinated temporary exhibition, much new information was uncovered about the collections of Blaschka objects in Ireland, including a total of nearly 800 surviving models. The history of the artists shows a clever business model that was designed to tap a niche market in the contemporary fascination with natural history, and improved through the course of several decades with input from clients and their own passion for understanding their biological subjects. From a modern perspective, a single Blaschka glass model of a marine invertebrate can embody biology, the history of science, craftsmanship, glass chemistry, aesthetics and art. This ability to cross interdisciplinary bridges is a singular strength of the Blaschka works, and is evident in the published proceedings of the Congress.

Artificial Impedance Surfaces for Reduced Dispersion in Antenna Feeding Systems

An impedance surface is presented that reduces the dispersion experienced upon propagation of broadband pulses within rectangular waveguides. The surface impedance is selected so that, within a frequency range, the transverse resonance condition is satisfied for longitudinal wavenumber that varies linearly with frequency. A synthesis procedure for practical surface topologies consisting of periodic dipole arrays is described. An example involving a finite structure is employed to illustrate the reduced dispersion. Numerical simulation results obtained from in-house mode-matching method as well as HFSS are presented. A prototype is fabricated and tested experimentally validating the theoretical predictions.

Sub-Wavelength Profile 2-D Leaky-Wave Antennas With Two Periodic Layers

A fast and accurate analysis and synthesis technique for high-gain sub-wavelength 2-D Fabry-Perot leaky-wave antennas (LWA) consisting of two periodic metallodielectric arrays over a ground plane is presented. Full-wave method of moments (MoM) together with reciprocity is employed for the estimation of the near fields upon plane wave illumination and the extraction of the radiation patterns of the LWA. This yields a fast and rigorous tool for the characterisation of this type of antennas. A thorough convergence study for different antenna designs is presented and the operation principles of these antennas as well as the radiation characteristics are discussed. Moreover, design guidelines to tailor the antenna profile, the dimensions of the arrays as well as the antenna directivity and bandwidth are provided. A study on the radiation efficiency for antennas with different profiles is also presented and the trade off between directivity and radiation bandwidth is discussed. Numerical examples are given throughout to demonstrate the technique. A finite size antenna model is simulated using commercial software (CST Microstripes 2009) which validates the technique.

Frequency Steerable Two Dimensional Focusing Using Rectilinear Leaky-Wave Lenses

The concept of frequency steerable two-dimensional electromagnetic focusing by using a tapered leaky-wave line source embedded in a parallel-plate medium is presented. Accurate expressions for analyzing the focusing pattern of a rectilinear leaky-wave lens (LWL) from its constituent leaky-mode tapered propagation constant are described. The influence of the main LWL structural parameters on the synthesis of the focusing pattern is discussed. The ability to generate frequency steerable focusing patterns has been demonstrated by means of an example involving a LWL in hybrid waveguide printed-circuit technology and the results are validated by a commercial full-wave solver.

Far field subwavelength source resolution using Phase Conjugating Lens Assisted With Evanescent-to-Propagating Spectrum Conversion

The imaging properties of a phase conjugating lens operating in the far field zone of the imaged source and augmented with scatterers positioned in the source near field region are theoretically studied in this paper. The phase conjugating lens consists of a double sided 2D assembly of straight wire elements, individually interconnected through phase conjugation operators. The scattering elements are straight wire segments which are loaded with lumped impedance loads at their centers. We analytically and numerically analyze all stages of the imaging process; i) evanescent-to-propagating spectrum conversion; ii) focusing properties of infinite or finite sized phase conjugating lens; iii) source reconstruction upon propagating-to-evanescent spectrum conversion. We show that the resolution that can be achieved depends critically on the separation distance between the imaged source and scattering arrangement, as well as on the topology of the scatterers used. Imaged focal widths of up to one-seventh wavelength are demonstrated. The results obtained indicate the possibility of such an arrangement as a potential practical means for realising using conventional materials devices for fine feature extraction by electromagnetic lensing at distances remotely located from the source objects under investigation

Power Stored and Quality Factors in Frequency Selective Surfaces at THz Frequencies

A study of the external, loaded and unloaded quality factors for frequency selective surfaces (FSSs) is presented. The study is focused on THz frequencies between 5 and 30 THz, where ohmic losses arising from the conductors become important. The influence of material properties, such as metal thickness, conductivity dispersion and surface roughness, is investigated. An equivalent circuit that models the FSS in the presence of ohmic losses is introduced and validated by means of full-wave results. Using both full-wave methods as well as a circuit model, the reactive energy stored in the vicinity of the FSS at resonance upon plane-wave incidence is presented. By studying a doubly periodic array of aluminium strips, it is revealed that the reactive power stored at resonance increases rapidly with increasing periodicity. Moreover, it is demonstrated that arrays with larger periodicity-and therefore less metallisation per unit area-exhibit stronger thermal absorption. Despite this absorption, arrays with higher periodicities produce higher unloaded quality factors. Finally, experimental results of a fabricated prototype operating at 14 THz are presented.

Sub-mm wet etched linear to circular polarization fss based polarization converters

This communication investigates the potential for fabrication of micromachined silicon sub-millimeter wave periodic arrays of freestanding slot frequency selective surfaces (FSS) using wet etch KOH technology. The vehicle for this is an FSS for generating circularly polarized signals from an incident linearly polarized signal at normal incidence to the structure. Principal issues and fabrication processes involved from the initial design of the core FSS structures to be made and tested through to their final testing are addressed. Measured and simulated results for crossed and ring slot element shapes in single and double layer polarization convertor structures are presented for sub-mm wave operation. It is shown that 3 dB axial ratio (AR) bandwidths of 21% can be achieved with the one layer perforated screen design and that the rate of change is lower than the double layer structures. An insertion loss of 1.1 dB can be achieved for the split circular ring double layer periodic array. These results are shown to be compatible with the more specialized fabrication equipment dry reactive ion etching approach previously used for the construction of this type of structure. © 2011 IEEE.

Correction for a possible reversible adsorption over an "inert" material

All TAP micro-reactor configurations contain inert particles which are used so that the catalyst zone can be maintained under isothermal conditions. Even on

Combining multisensory temporal information for movement synchronisation

The ability to synchronise actions with environmental events is a fundamental skill supporting a variety of group activities. In such situations, multiple sensory cues are usually available for synchronisation, yet previous studies have suggested that auditory cues dominate those from other modalities. We examine the control of rhythmic action on the basis of auditory and haptic cues and show that performance is sensitive to both sources of information for synchronisation. Participants were required to tap the dominant hand index finger in synchrony with a metronome defined by periodic auditory tones, imposed movements of the non-dominant index finger, or both cues together. Synchronisation was least variable with the bimodal metronome as predicted by a maximum likelihood estimation (MLE) model. However, increases in timing variability of the auditory cue resulted in some departures from the MLE model. Our findings indicate the need for further investigation of the MLE account of the integration of multisensory signals in the temporal control of action.

Interval timing and trajectory in unequal amplitude movements

The Wing-Kristofferson (WK) model of movement timing emphasises the separation of central timer and motor processes. Several studies of repetitive timing have shown that increase in variability at longer intervals is attributable to timer processes; however, relatively little is known about the way motor aspects of timing are affected by task movement constraints. In the present study, we examined timing variability in finger tapping with differences in interval to assess central timer effects, and with differences in movement amplitude to assess motor implementation effects. Then, we investigated whether effects of motor timing observed at the point of response (flexion offset/tap) are also evident in extension, which would suggest that both phases are subject to timing control. Eleven participants performed bimanual simultaneous tapping, at two target intervals (400, 600 ms) with the index finger of each hand performing movements of equal (3 or 6 cm) or unequal amplitude (left hand 3, right hand 6 cm and vice versa). As expected, timer variability increased with the mean interval but showed only small, non-systematic effects with changes in movement amplitude. Motor implementation variability was greater in unequal amplitude conditions. The same pattern of motor variability was observed both at flexion and extension phases of movement. These results suggest that intervals are generated by a central timer, triggering a series of events at the motor output level including flexion and the following extension, which are explicitly represented in the timing system.