Maintaining design intent for aircraft manufacture

Design and manufacture of aircraft requires deep multi-disciplinary understanding of system behaviour. The intention of the designer can get lost due to the many changes occurring to the product and the inability of the methods and tools used to capture it. Systems engineering and optimisation tools underpin industrial approaches to design, but are not without issue. The challenge is to find a route from concept to manufacture which enables designers to maintain their original intent. The novelty in this work is that the parameterisation used to build the CAD model reflects the manufacturing capability, ensuring design intent is maintained from concept to manufacture.

Evaluation of methodologies to determine vegetable oil species present in oil mixtures: Proposition of an approach to meet the EU legislation demands for correct vegetable oils labelling

Refined vegetable oils are widely used in the food industry as ingredients or components in many processed food products in the form of oil blends. To date, the generic term 'vegetable oil' has been used in the labelling of food containing oil blends. With the introduction of new EU Regulation for Food Information (1169/2011) due to take effect in 2014, the oil species used must be clearly identified on the package and there is a need for development of fit for purpose methodology for industry and regulators alike to verify the oil species present in a product. The available methodologies that may be employed to authenticate the botanical origin of a vegetable oil admixture were reviewed and evaluated. The majority of the sources however, described techniques applied to crude vegetable oils such as olive oil due to the lack of refined vegetable oil focused studies. Nevertheless, DNA based typing methods and stable isotopes procedures were found not suitable for this particular purpose due to several issues. Only a small number of specific chromatographic and spectroscopic fingerprinting methods in either targeted or untargeted mode were found to be applicable in potentially providing a solution to this complex authenticity problem. Applied as a single method in isolation, these techniques would be able to give limited information on the oils identity as signals obtained for various oil types may well be overlapping. Therefore, more complex and combined approaches are likely to be needed to identify the oil species present in oil blends employing a stepwise approach in combination with advanced chemometrics. Options to provide such a methodology are outlined in the current study.

US Patent: Composite concrete article and method of manufacture thereof

A method of manufacturing a composite concrete article comprising affixing at least one layer of textile to a base layer and incorporating the base layer into a body of wet uncured concrete such that the base layer becomes embedded in the concrete, whereby at least a portion of the at least one textile layer defines at least a portion of a surface of the cured concrete article with the base layer embedded within the concrete to anchor the textile layer to the concrete.

The Application of Computational Chemistry and Chemometrics to Developing a Method for Online Monitoring of Polymer Degradation in the Manufacture of Bioresorbable Medical Implants

Bioresorbable polymers such as PLA have an important role to play in the development of temporary implantable medical devices with significant benefits over traditional therapies. However, development of new devices is hindered by high manufacturing costs associated with difficulties in processing the material. A major problem is the lack of insight on material degradation during processing. In this work, a method of quantifying degradation of PLA using IR spectroscopy coupled with computational chemistry and chemometric modeling is examined. It is shown that the method can predict the quantity of degradation products in solid-state samples with reasonably good accuracy, indicating the potential to adapt the method to developing an on-line sensor for monitoring PLA degradation in real-time during processing.

Considerations in the sterile manufacture of polymeric microneedle arrays

We describe, for the first time, considerations in the sterile manufacture of polymeric microneedle arrays. Microneedles (MN) made from dissolving polymeric matrices and loaded with the model drugs ovalbumin (OVA) and ibuprofen sodium and hydrogel-forming MN composed of "super-swelling" polymers and their corresponding lyophilised wafer drug reservoirs loaded with OVA and ibuprofen sodium were prepared aseptically or sterilised using commonly employed sterilisation techniques. Moist and dry heat sterilisation, understandably, damaged all devices, leaving aseptic production and gamma sterilisation as the only viable options. No measureable bioburden was detected in any of the prepared devices, and endotoxin levels were always below the US Food & Drug Administration limits (20 endotoxin units/device). Hydrogel-forming MN were unaffected by gamma irradiation (25 kGy) in terms of their physical properties or capabilities in delivering OVA and ibuprofen sodium across excised neonatal porcine skin in vitro. However, OVA content in dissolving MN (down from approximately 101.1 % recovery to approximately 58.3 % recovery) and lyophilised wafer-type drug reservoirs (down from approximately 99.7 % recovery to approximately 60.1 % recovery) was significantly reduced by gamma irradiation, while the skin permeation profile of ibuprofen sodium from gamma-irradiated dissolving MN was markedly different from their non-irradiated counterparts. It is clear that MN poses a very low risk to human health when used appropriately, as evidenced here by low endotoxin levels and absence of microbial contamination. However, if guarantees of absolute sterility of MN products are ultimately required by regulatory authorities, it will be necessary to investigate the effect of lower gamma doses on dissolving MN loaded with active pharmaceutical ingredients and lyophilised wafers loaded with biomolecules in order to avoid the expense and inconvenience of aseptic processing.

A Numerical and Experimental Assessment of the Use of a Turbine Utilizing Splitter Blades for an Automotive Variable Geometry Turbocharger

Automotive manufacturers require improved part load engine performance to further improve fuel economy. For a swing vane VGS (Variable Geometry Stator) turbine this means a more closed stator vane, to deal with the low MFRs (Mass Flow Rates), high PRs (Pressure Ratios) and low rotor rotational speeds. During these conditions the turbine is operating at low velocity ratios. As more energy is available at high pressure ratios and during lower turbocharger rotational speeds, a turbine which is efficient at these conditions is desirable. Another key aspect for automotive manufacturers is engine responsiveness. High inertia designs result in “turbo lag” which means an increased time before the target boost pressure is reached. Therefore, designs with improved performance at low velocity ratios, reduced inertia or an increased swallowing capacity are the current targets for turbocharger manufacturers.

To try to meet these design targets a CFD (Computational Fluid Dynamics) study was performed on a turbine wheel using splitter blades. A number of parameters were investigated. These included splitter blade merdional length, blade number and blade angle distribution.

The numerical study was performed on a scaled automotive VGS. Three different stator vane positions have been analysed. A single passage CFD model was developed and used to provide information on the flow features affecting performance in both the stator vanes and turbine.

Following the CFD investigation the design with the best compromise in terms of performance, inertia and increased MFP (Mass Flow Parameter) was selected for manufacture and testing. Tests were performed on a scaled, low temperature turbine test rig. The aerodynamic flow path of the gas stand was the same as that investigated during the CFD. The test results revealed a design which had similar performance at the closed stator vane positions when compared to the baseline wheel. At the maximum MFR stator vane condition a drop of −0.6% pts in efficiency was seen. However, 5.5% increase in MFP was obtained with the additional benefit of a drop in rotor inertia of 3.7%, compared to the baseline wheel.