Microstructure and mechanical properties of low nickel maraging steel

Austenitization with lower temperature and intercritical annealing were introduced in the treatment of a maraging steel with a composition of Fe–12.94Ni–1.61Al–1.01Mo–0.23Nb (wt.%). Scanning electron microscopy was employed to study the microstructure after austenitization at 950 °C and intercritical annealing, followed by aging at 485 and 600 °C. X-ray diffraction (XRD) analysis was applied to evaluate the formation of retained or reverted austenite. Thermodynamic calculation was employed to calculate equilibrium phase mole fractions. Hardness and Charpy impact toughness of the steel were measured. Intercritical annealing treatments did not result in significant increase of hardness either before or after aging. The Charpy impact toughness of the alloy in aged condition was enhanced after austenitization at 950 °C. No austenite was observed in XRD. However, suspected reverted austenite was found after austenitization at 950 °C followed by aging at 600 °C for 4 h. Relationships among heat treatment, microstructure and mechanical properties are discussed.

Investigation of the effect of the preparation method on the activity and stability of Au/CeZrO4 catalysts for the low temperature water gas shift reaction

The impact of the preparation method on the activity and stability of gold supported on ceria-zirconia low temperature water-gas shift (WGS) catalysts have been investigated. The influence of the gold deposition method, nature of the gold precursor, nature of the washing solution, drying method, Ce: Zr ratio of the support and sulfation of the support have been evaluated. The highest activity catalysts were obtained using a support with a Ce: Zr mole ratio 1: 1, HAuCl4 as the gold precursor deposited via deposition precipitation using sodium carbonate as the precipitation agent and the catalyst washed with water or 0.1 M NH4OH solution. In addition, the drying used was found to be critical with drying under vacuum at room temperature found to be most effective.

Low flow water quality in rivers; septic tank systems and high-resolution phosphorus signals

Rural point sources of phosphorus (P), including septic tank systems, provide a small part of the overall phosphorus budget to surface waters in agricultural catchments but can have a disproportionate impact on the low flow P concentration of receiving rivers. This has particular importance as the discharges are approximately constant into receiving waters and these have restricted dilution capacity during ecologically sensitive summer periods. In this study, a number of identified high impact septic systems were replaced with modern sequential batch reactors in three rural catchments during a monitoring period of 4 years. Sub-hourly P monitoring was conducted using bankside-analysers. Results show that strategic replacement of defective septic tank systems with modern systems and polishing filters decreased the low flow P concentration of one catchment stream by 0.032 mg TP L- 1 (0.018 mg TRP L- 1) over the 4 years. However two of the catchment mitigation efforts were offset by continued new-builds that increased the density of septic systems from 3.4 km- 2 to 4.6 km- 2 and 13.8 km- 2 to 17.2 km- 2 and subsequently increased low flow P concentrations. Future considerations for septic system mitigation should include catchment carrying capacity as well as technology changes.

Electron-impact excitation of Fe II

We report in this paper the computation of accurate total collision strengths and effective collision strengths for electron-impact excitation of FeII, using the parallel R-matrix program PRMAT. Target states corresponding to the 3d(6)4s, 3d(7), 3d(6)4p and 3d(5)4s4s basis configurations were included in the calculations giving rise to a 113 LS state 354 coupled channel problem. Following a detailed systematic study of correlation effects in both the target state and collision wavefunctions, it was found that an additional 21 configuration functions needed to be included in the Configuration Interaction expansion to obtain significantly more accurate target states and collision wavefunctions. This much improved 26-configuration model has been used to calculate converged total effective collision strengths for all sextet to quartet transitions among these levels with total spin S=2, giving a total of 1785 lines. These calculations have laid the foundation for an approach which may be adopted in the study of electron collisions with the low ionization stages of other iron peak elements. The work has been further extended with the commencement of a Breit-Pauli relativistic calculation for one of the smaller models and includes 262 fine-structure levels and over 1800 coupled channels. At the same time the PRMAT parallel R-matrix package is being extended to include relativistic effects which will allow us to attempt the more sophisticated 26-configuration model and produce for the first time the amount and quality of atomic data required to perform a meaningful synthesis of the Fe II spectrum.

A field study assessing the impact of on-site wastewater treatment systems on surface water quality in a Co. Monaghan catchment

Poorly functioning on-site wastewater treatment systems (OSWTS) can be among the many sources of pollution to groundwater and surface water, which are of critical concern owing to potential human and ecological health risks. An investigation into the effects of on-site wastewater treatment systems (OSWTS) on surface water quality has been undertaken at several sites within a catchment in Co. Monaghan. The study sites were located in areas of 'low’ permeability, suggesting that run-off usually dominates over infiltration. Poor treatment performance of OSWTS within the catchment were found to be the result of several factors, including location in areas with unsuitable soil and site characteristics, incorrect installation, poor maintenance and inappropriate operation by the home owner.

Low MAD2 expression levels associate with reduced progression-free survival in patients with high-grade serous epithelial ovarian cancer

Epithelial ovarian cancer (EOC) has an innate susceptibility to become chemoresistant. Up to 30% of patients do not respond to conventional chemotherapy [paclitaxel (Taxol®) in combination with carboplatin] and, of those who have an initial response, many patients relapse. Therefore, an understanding of the molecular mechanisms that regulate cellular chemotherapeutic responses in EOC cells has the potential to impact significantly on patient outcome. The mitotic arrest deficiency protein 2 (MAD2), is a centrally important mediator of the cellular response to paclitaxel. MAD2 immunohistochemical analysis was performed on 82 high-grade serous EOC samples. A multivariate Cox regression analysis of nuclear MAD2 IHC intensity adjusting for stage, tumour grade and optimum surgical debulking revealed that low MAD2 IHC staining intensity was significantly associated with reduced progression-free survival (PFS) (p = 0.0003), with a hazard ratio of 4.689. The in vitro analyses of five ovarian cancer cell lines demonstrated that cells with low MAD2 expression were less sensitive to paclitaxel. Furthermore, paclitaxel-induced activation of the spindle assembly checkpoint (SAC) and apoptotic cell death was abrogated in cells transfected with MAD2 siRNA. In silico analysis identified a miR-433 binding domain in the MAD2 3' UTR, which was verified in a series of experiments. Firstly, MAD2 protein expression levels were down-regulated in pre-miR-433 transfected A2780 cells. Secondly, pre-miR-433 suppressed the activity of a reporter construct containing the 3'-UTR of MAD2. Thirdly, blocking miR-433 binding to the MAD2 3' UTR protected MAD2 from miR-433 induced protein down-regulation. Importantly, reduced MAD2 protein expression in pre-miR-433-transfected A2780 cells rendered these cells less sensitive to paclitaxel. In conclusion, loss of MAD2 protein expression results in increased resistance to paclitaxel in EOC cells. Measuring MAD2 IHC staining intensity may predict paclitaxel responses in women presenting with high-grade serous EOC.

Low temperature conditions in building sandstone: the role of extreme events in temperate environments

Data on rock temperatures has previously been collected to characterise typical diurnal regimes, and more recently to describe short-term variability in extreme locations. However, there is also the case that little is understood concerning the impact of extreme events in otherwise temperate environments. Internal stone temperatures (5?cm) collected during the atypical cold extreme experienced, throughout the UK, in December 2010 show a difference between ambient air temperatures and aspect-related thermal differences, particularly concerning temperature lows and the influence of radiative heating. In this case, debris release was not visible; however, laboratory simulations have shown that under such conditions, surface loss does not necessarily negate the occurrence of internal stone modifications. This preparatory sequence of change demonstrates that surface loss is not the result of one process, but rather many operating over time to sufficiently decrease stone strength to facilitate obvious damage.

Efficient modelling and optimisation of hybrid multilayered plates subject to ballistic impact

Among the key challenges present in the modelling and optimisation of composite structures against impact is the computational expense involved in setting up accurate simulations of the impact event and then performing the iterations required to optimise the designs. It is of more interest to find good designs given the limitations of the resources and time available rather than the best possible design. In this paper, low cost but sufficiently accurate finite element (FE) models were generated in LS Dyna for several experimentally characterised materials by semi-automating the modelling process and using existing material models. These models were then used by an optimisation algorithm to generate new hybrid offspring, leading to minimum weight and/or cost designs from a selection of isotropic metals, polymers and orthotropic fibre-reinforced laminates that countered a specified impact threat. Experimental validation of the optimal designs thus identified was then successfully carried out using a single stage gas gun. With sufficient computational hardware, the techniques developed in this pilot study can further utilise fine meshes, equations of state and sophisticated material models, so that optimal hybrid systems can be identified from a wide range of materials, designs and threats.

On the application of genetic algorithms for optimising composites against impact loading

A genetic algorithm (GA) was adopted to optimise the response of a composite laminate subject to impact. Two different impact scenarios are presented: low-velocity impact of a slender laminated strip and high-velocity impact of a rectangular plate by a spherical impactor. In these cases, the GA's objective was to, respectively, minimise the peak deflection and minimise penetration by varying the ply angles.

The GA was coupled to a commercial finite-element (FE) package LS DYNA to perform the impact analyses. A comparison with a commercial optimisation package, LS OPT, was also made. The results showed that the GA was a robust, capable optimisation tool that produced near optimal designs, and performed well with respect to LS OPT for the more complex high-velocity impact scenario tested.

Maternal Vitamin D Status in Type 1 Diabetic Pregnancy: Impact on Neonatal Vitamin D Status and Association with Maternal Glycaemic Control

Objective: The first aim of this study was to assess 25-hydroxy vitamin D (25OHD) concentrations in women with type 1 diabetes (T1DM) during pregnancy, post-delivery and also foetal (cord blood) 25OHD concentrations and to examine relationships between these. The second aim of the study was to investigate potential interactions between maternal body mass index (BMI) and foetal vitamin D status. A further study aim was to examine potential relationships between maternal 25OHD and glycosylated haemoglobin (HbA_1c) throughout pregnancy.

Research Design and Methods: This was an observational study of 52 pregnant controls without diabetes and 65 pregnant women with T1DM in a university teaching hospital. Maternal serum 25OHD was measured serially throughout the pregnancy and post-delivery. Cord blood 25OHD was measured at delivery. 25OHD was measured by liquid chromatography tandem mass spectrometry (LC-MS/MS).

Results: Vitamin D deficiency (25OHD <25 nmol/L) was apparent in both the T1DM subjects and controls at all 3 pregnancy trimesters. Vitamin D levels in all cord blood were <50 nmol/L. Maternal 25OHD correlated positively with cord 25OHD at all 3 trimesters in the T1DM group (p= 0.02; p<0.001; p<0.001). 25OHD levels within cord blood were significantly lower for women with diabetes classified as obese vs. normal weight at booking [normal weight BMI <25 kg/m² vs. obese BMI >30 kg/m² (nmol/L±SD); 19.93±11.15 vs. 13.73±4.74, p= 0.026]. In the T1DM group, HbA_1c at booking was significantly negatively correlated with maternal 25OHD at all 3 trimesters (p= 0.004; p = 0.001; p= 0.05).

Conclusion: In T1DM pregnancy, low vitamin D levels persist throughout gestation and post-delivery. Cord blood vitamin D levels correlate with those of the mother, and are significantly lower in obese women than in their normal weight counterparts. Maternal vitamin D levels exhibit a significant negative relationship with HbA_1c levels, supporting a potential role for this vitamin in maintaining glycaemic control. 

The impact of union presence and strategic human resource management on employee voice in multinational enterprises in Australia

In this article, we examine the use and character of employee voice mechanisms of foreign-owned multinational enterprises operating in Australia, as well as the influence of a strategic human resource management approach and union presence. Findings indicate that foreign-owned multinational enterprises are high-level users of the full range of employee voice mechanisms, with the exceptions of use of employee suggestion schemes, trade union recognition and the use of joint consultation committees across all sites. Using logistic regression analysis, findings show that trade union presence, a strategic human resource management approach, greenfield site and country of origin impact the employee voice approach adopted. High trade union presence is associated with an indirect employee voice approach. A low trade union presence is associated with a direct or a minimalist approach to employee voice. Moreover, a strategic human resource management approach is associated with both direct and dualistic approaches to employee voice. Implications are drawn for theory and practice. © Australian Labour and Employment Relations Association (ALERA) SAGE Publications Ltd, Los Angeles, London, New Delhi, Singapore and Washington DC.

Multibody modelling of gabion beams for impact applications

Gabions are stone-filled wire containers which are frequently used as retaining walls. However, due to their high mass, relatively low cost and visual appeal, a row of single gabion blocks, joined at the ends, has the potential to be used as a roadside impact absorption device where traditional steel or concrete devices may not be suitable. To evaluate such application, the shear and bending deformation of gabions under vehicle impact need to be investigated. In this paper, the shear response of a single gabion block is analytically modelled and a gabion beam multibody model is developed using a discretisation method to capture the deformability of the gabion structure. The material properties of the gabion beam are adopted from experimental values available in the literature and the modelling is statically validated over a three-point bending test and a distributed loading test. The results show that the discretised multibody modelling can be effectively used to describe the static deformation behaviour of gabion blocks.

Analysis of Fixed-Speed Wind Farm Low-Frequency Power Pulsations using a Wavelet-Prony Method

The increasing penetration of wind generation on the Island of Ireland has been accompanied by close investigation of low-frequency periodic pulsations contained within the active power flow from different wind farms. A primary concern is excitation of existing low-frequency oscillation modes already present on the system, particularly the 0.75 Hz mode as a consequence of the interconnected Northern and Southern power system networks. Recently grid code requirements on the Northern Ireland power system have been updated stipulating that wind farms connected after 2005 must be able to control the magnitude of oscillations in the range of 0.25 - 1.75 Hz to within 1% of the wind farm's registered output. In order to determine whether wind farm low-frequency oscillations have a negative effect (excite other modes) or possibly a positive impact (damping of existing modes) on the power system, the oscillations at the point of connection must be measured and characterised. Using time - frequency methods, research presented in this paper has been conducted to extract signal features from measured low-frequency active power pulsations produced by wind farms to determine the effective composition of possible oscillatory modes which may have a detrimental effect on system dynamic stability. The paper proposes a combined wavelet-Prony method to extract modal components and determine damping factors. The method is exemplified using real data obtained from wind farm measurements.

Impact of Heat Pump Load on Distribution Networks

Heat pumps can provide domestic heating at a cost that is competitive with oil heating in particular. If the electricity supply contains a significant amount of renewable generation, a move from fossil fuel heating to heat pumps can reduce greenhouse gas emissions. The inherent thermal storage of heat pump installations can also provide the electricity supplier with valuable flexibility. The increase in heat pump installations in the UK and Europe in the last few years poses a challenge for low-voltage networks, due to the use of induction motors to drive the pump compressors. The induction motor load tends to depress voltage, especially on starting. The paper includes experimental results, dynamic load modelling, comparison of experimental results and simulation results for various levels of heat pump deployment. The simulations are based on a generic test network designed to capture the main characteristics of UK distribution system practice. The simulations employ DIgSlILENT to facilitate dynamic simulations that focus on starting current, voltage variations, active power, reactive power and switching transients.

Existing and emerging high impact invasive species are characterized by higher functional responses than natives

Predicting ecological impacts of invasive species and identifying potentially damaging future invaders are research priorities. Since damage by invaders is characterized by their depletion of resources, comparisons of the ‘functional response’ (FR; resource uptake rate as a function of resource density) of invaders and natives might predict invader impact. We tested this by comparing FRs of the ecologically damaging ‘world's worst’ invasive fish, the largemouth bass (Micropterus salmoides), with a native equivalent, the Cape kurper (Sandelia capensis), and an emerging invader, the sharptooth catfish (Clarias gariepinus), with the native river goby (Glossogobius callidus), in South Africa, a global invasion hotspot. Using tadpoles (Hyperolius marmoratus) as prey, we found that the invaders consumed significantly more than natives. Attack rates at low prey densities within invader/native comparisons reflected similarities in predatory strategies; however, both invasive species displayed significantly higher Type II FRs than the native comparators. This was driven by significantly lower prey handling times by invaders, resulting in significantly higher maximum feeding rates. The higher FRs of these invaders are thus congruent with, and can predict, their impacts on native communities. Comparative FRs may be a rapid and reliable method for predicting ecological impacts of emerging and future invasive species.