Performance enhancement of polymer nanocomposites via multiscale modelling of processing and properties

This paper provides an overview of research on modelling of the structure–property interactions of polymer nanocomposites in manufacturing processes (stretch blow moulding and thermoforming) involving large-strain biaxial stretching of relatively thin sheets, aimed at developing computer modelling tools to help producers of materials, product designers and manufacturers exploit these materials to the full, much more quickly than could be done by experimental methods alone. The exemplar systems studied are polypropylene and polyester terephalate, with nanoclays. These were compounded and extruded into 2mm thick sheet which was then biaxially stretched at 155°C for the PP and 90 to 100°C for the PET. Mechanical properties were determined for the unstretched and stretched materials, together with TEM and XRD studies of structure. Multi-scale modelling, using representative volume elements is used to model the properties of these products.

Effects of storage on thermomechanical properties of poly(epsilon-caprolactone) blends containing poly(vinyl pyrrolidone/iodine)

This study reports the effects of: the molecular weight ratio of poly(epsilon -caprolactone) (PCL) in blends containing polymer of high (50 000 g mol(-1)) and low (4000 g mol(-1)) molecular weight; the concentration (0, 1, and 5 wt-%) of poly(vinyl pyrrolidone/iodine) (PVP/I); and storage at 30 degreesC and 75% relative humidity; on the thermomechanical properties of films prepared by solvent evaporation from solutions containing both PCL and PVP/I. The tensile properties were found to be statistically dependent on the molecular weight ratio of PCL but not on the concentration of PVP/I. The reductions in tensile strength and elongation at break associated with increasing amounts of low molecular weight PCL were attributed to a reduction in the concentration of chain entanglements. No changes were observed in viscoelastic properties or the glass transition temperature. Following storage there were no changes in the tensile strength, glass transition temperature, or viscoelastic properties of the films; however, significant reductions in elongation at break were observed. It is suggested that this is due to hydrolytic chain scission of amorphous PCL. Inclusion of 5 wt-% PVP/I increased this process in films containing 100:0 and 80:20 high/low molecular weight PCL (but not 60.40), but the extent of this was small. This study highlighted significant aging properties of PCL in a moist atmosphere. Consequently, it is recommended that suitable packaging materials should be employed to control the exposure of PCL films to water during storage.

Modelling of poly(ethylene terephthalate) in injection stretch-blow moulding

Simulations of the injection stretch-blow moulding process have been developed for the manufacture of poly(ethylene terephthalate) bottles using the commercial finite element package ABAQUS/standard. Initially a simulation of the manufacture of a 330 mL bottle was developed with three different material models (hyperelastic, creep, and a non-linear viscoelastic model (Buckley model)) to ascertain their suitability for modelling poly(ethylene terephthalate). The Buckley model was found to give results for the sidewall thickness that matched best with those measured from bottles off the production line. Following the investigation of the material models, the Buckley model was chosen to conduct a three-dimensional simulation of the manufacture of a 2 L bottle. It was found that the model was also capable of predicting the wall thickness distribution accurately for this bottle. In the development of the three-dimensional simulation a novel approach, which uses an axisymmetric model until the material reaches the petaloid base, was developed. This resulted in substantial savings in computing time. © 2000 IoM Communication Ltd.

Optimization of the processing of HNBR/organoclay nanocomposite

In the current investigation, rubber/clay nanocomposites were prepared by two different methods using hydrogenated nitrile butadiene rubber (HNBR) and the organoclay namely Cloisite 15A (C15A). A new novel approach involving swelling of C15A by ulltrasonication in HNBR solution has been carried out for improving the exfoliation and compatibilization of organoclays with HNBR matrix. With the addition of 5phr of clay, the elongation at break and tear strength improved by 16% and 24% respectively. The effect of coupling agents namely amino functional silane and tetrasulfido silane on the nanocomposites have been investigated. The elongation at break and tear strength improved by 46% and 77% respectively with the use of silanes. The improvement in the mechanical properties attributes to improved interaction between the organoclays and HNBR matrix. This interaction has been studied by X-ray diffraction and transmission electron microscope. Pre-dispersion technique clearly suggests very good improvement in the dispersion and properties due to better filler-rubber compatibility. © 2010 American Institute of Physics.

Mechanism of gas permeation in processed HNBR/nanoclay composites

The influence of the layered silicate clay platelets on the nitrogen permeation properties of hydrogenated nitrile butadiene rubber (HNBR)/nanoclay nanocomposites has been investigated. Nanocomposites of HNBR modified with different percentages of the organoclay are processed through various routes. Commercially available organoclay (CLOISITE 15A) and various silane-coupling agents are used to improve the dispersion of the nanoclay in HNBR. A total of 10 different formulations of nanocomposites are manufactured. The addition of the organoclay has resulted in a significant enhancement of the nitrogen barrier properties of the manufactured nanocomposite. The mechanism of the reduction in the permeability is explained through the changes in the morphology and its bond to the filler. These changes are confirmed through examination of the morphology using x-ray diffraction, transmission electron microscope, and dynamic mechanical thermal analysis. There has been a drastic reduction up to 55.7% in nitrogen permeability. The reduction in gas permeation in HNBR is attributed to uniformly exfoliated clay platelets. Finally, three different permeability models, namely, the Nielsen model, modified Nielsen model, and Cussler model, have also been considered to predict the permeability behavior of nanocomposites with different volume filler fractions. The experimental values of gas permeability have been compared with theoretical models. It is observed that the modified Nielsen model closely matches with the measured permeation behavior. © 2011 Wiley Periodicals, Inc.

Optimized process for the inclusion of carbon nanotubes in elastomers with improved thermal and mechanical properties

The effects of addition of reinforcing carbon nanotubes (CNTs) into hydrogenated nitrile-butadiene rubber (HNBR) matrix on the mechanical, dynamic viscoelastic, and permeability properties were studied in this investigation. Different techniques of incorporating nanotubes in HNBR were investigated in this research. The techniques considered were more suitable for industrial preparation of rubber composites. The nanotubes were modified with different surfactants and dispersion agents to improve the compatibility and adhesion of nanotubes on the HNBR matrix. The effects of the surface modification of the nanotubes on various properties were examined in detail. The amount of CNTs was varied from 2.5 to 10 phr in different formulations prepared to identify the optimum CNT levels. A detailed analysis was made to investigate the morphological structure and mechanical behavior at room temperature. The viscoelastic behavior of the nanotube filler elastomer was studied by dynamic mechanical thermal analysis (DMTA). Morphological analysis indicated a very good dispersion of the CNTs for a low nanotube loading of 3.5 phr. A significant improvement in the mechanical properties was observed with the addition of nanotubes. DMTA studies revealed an increase in the storage modulus and a reduction in the glass-transition temperature after the incorporation of the nanotubes. Further, the HNBR/CNT nanocomposites were subjected to permeability studies. The studies showed a significant reduction in the permeability of nitrogen gas. Copyright © 2011 Wiley Periodicals, Inc.

Enhancement of the properties of EPDM/NBR elastomers using nanoclay for seal applications

In this research, we have investigated the effects of addition of different percentages of nanoclay to the ethylene propylene diene monomer (EPDM) and nitrile butadiene rubber (NBR) on the characteristics of these rubbers as seal material. Properties such as tensile strength, modulus at different extensions, elongation at break, compressive set, hardness, and permeability and abrasion resistance are tested to assess the effect of addition of the nanoclay. Results indicate that addition of nanoclay at certain compositions could slightly reduce the strength of the rubber. However more stable modulus at different strains are provided, the hardness of the rubber is preserved and slightly enhanced, the permeability is reduced in both rubbers especially considerable decrease in EPDM is observed which is desirable in diminishing the effect of explosive decompression. At the same time the compression test shows that the nanoclay improves the performance of the rubbers under compression which is essential in seal application. The X-ray diffraction tests clarify that the dispersion of the nanoclay in the NBR samples is of high quality. In the EPDM samples, the dispersion is in need of improvement. POLYM. COMPOS., 30:1657-1667, 2009. © 2008 Society of Plastics Engineers.

Hard coatings on elastomers for reduced permeability and increased wear resistance

In this study, three different elastomers, namely hydrogenated nitrile butadiene rubber, fluoroelastomer and silicone, have been subjected to two different hard metallised coatings by ion implantation process. The three different elastomers are commonly used in various seal applications, where reduced wear and gas permeability are essential in maintaining seal performance and functionality. Samples of these rubbers have been coated with chromium coating in one set of tests. In the second set of tests, samples of elastomers have been coated with tungsten carbide coating being deposited on all the three different elastomers. Wear, gas permeability and mechanical behaviour of the coated samples were compared with each other and with the control uncoated elastomers. All the coated samples showed good reduction in gas permeability. With the use of metallised coatings, there has been improved resistance to wear in all the coated samples. Adhesion strength and effect of coating on the elastomer have been investigated by mechanical testing. Mechanical tests revealed good adhesion of metal coatings on all the rubber samples, and there was no detrimental effect on the mechanical properties after coating. © 2012 Institute of Materials, Minerals and Mining.

Day case stapled haemorrhoidopexy for prolapsing haemorrhoids

Objective Conventional surgical management of prolapsing haemorrhoids is by excisional haemorrhoidectomy. Postoperative pain has restricted the application of such procedures in the day case setting. These operations remain associated with a period of restricted activity. The use of circular stapling devices as an alternative to the excisional approach in the management of haemorrhoids has been described. This study reports our experience of stapled haemorrhoidopexy as a day case procedure.

Methods Patients with third or fourth degree haemorrhoids were eligible for the procedure. Patients were considered suitable candidates for day case surgery based on conventional parameters. Symptoms were assessed using a previously validated symptom severity rating score. Stapled haemorrhoiclopexy was carried out using a circular stapling device. Pain scores were obtained prior to discharge. Patients were admitted if pain was uncontrolled despite oral analgesia. Symptoms were re-scored at six-week follow-up.

Results Over a 70-month period 168 consecutive stapled haemorrhoidopexies were performed or directly supervised by one consultant colorectal surgeon. One hundred and ten (65%) patients were considered appropriate candidates for day case surgery by conventional criteria. Ninety-six (87.3%) patients successfully underwent stapled haemorrhoidopexyon a day case basis. Fourteen (12.7%) patients required admission on the day of surgery (5 for early Postoperative bleeding, 4 for pain necessitating continuing opiate analgesia, two for urinary retention and three for surgery performed late in the day). Six (5%) patients were re-admitted postoperatively; four for pain relief and two because of urinary retention. Of the day case patients, 91 (82.7%) and 56 (50.9%) had been seen for 6 week and 6 month review, respectively, at the time of analysis. Symptom scores were 6 (pre-operatively) vs 0 (postoperatively) (P <0.01). 76/91 (83.5%) patients reviewed at 6/52 were asymptomatic.

Conclusion Stapled haemorrhoidopexy is a safe and effective procedure that can be carried out on selected patients on a day case basis. Complications are of a similar nature to excisional haemorrhoidectomy.

Synthesis of , of α,β-unsaturated aldehydes and nitriles via cross-metathesis reactions using Grubbs’ catalysts

A series of alpha,beta-unsaturated aldehydes and nitriles of significant interest in the fragrance industry have been prepared using Grubbs' catalysts in cross-metathesis reactions of electron-deficient olefins (i.e., acrolein, crotonaldehyde, methacrolein, and acrylonitrile) with various 1-alkenes, including 1-decene, 1-octene, 1-hexene and 2-allyloxy-6-methylheptane. The latter is of particular interest, as it has not previously being used as a substrate in cross-metathesis reactions and allows access to valuable intermediates for the synthesis of new fragrances. Most reactions gave good selectivity of the desired CM product (>= 90%). Detailed optimisation and mechanistic studies have been performed on the cross-metathesis of acrolein with 1-decene. Recycling of the catalyst has been attempted using ionic liquids.