Difference equation approach to two-thermocouple sensor characterisation in constant velocity flow environments

Thermocouples are one of the most popular devices for temperature measurement due to their robustness, ease of manufacture and installation, and low cost. However, when used in certain harsh environments, for example, in combustion systems and engine exhausts, large wire diameters are required, and consequently the measurement bandwidth is reduced. This article discusses a software compensation technique to address the loss of high frequency fluctuations based on measurements from two thermocouples. In particular, a difference equation sDEd approach is proposed and compared with existing methods both in simulation and on experimental test rig data with constant flow velocity. It is found that the DE algorithm, combined with the use of generalized total least squares for parameter identification, provides better performance in terms of time constant estimation without any a priori assumption on the time constant ratios of the thermocouples.

Blind Deconvolution for Two-thermocouple Sensor Characterisation

Thermocouples are one of the most popular devices for temperature measurement due to their robustness, ease of manufacture and installation, and low cost. However, when used in the harsh environment found in combustion systems and automotive engine exhausts, large wire diameters are required and consequently the measurement bandwidth is reduced. This paper describes two new algorithmic compensation techniques based on blind deconvolution to address this loss of high-frequency signal components using the measurements from two thermocouples. In particular, a continuous-time approach is proposed, combined with a cross-relation blind deconvolution for parameter estimation. A feature of this approach is that no a priori assumption is made about the time constant ratio of the two thermocouples. The advantages, including small estimation variance and limitations of the method, are highlighted using results from simulation and test rig studies.

Communal larval rearing of European lobster (Homarus gammarus): family identification by microsatellite DNA profiling an offspring fitness.

Stock enhancement experiments of European lobster (Homarus gammarus) have been carried out around the Kvitsoy Islands in south-western Norway since 1990. In addition to releases of coded wire tagged lobster juveniles (cultured) and subsequent monitoring of commercial fishery, a lobster hatchery was established in 1997. Several experiments were made on the communal-rearing approach where the performance of mixed larval groups (families) was evaluated under identical conditions. Berried females of wild and cultured origin and their respective fertilised eggs were screened by using microsatellite DNA profiling involving a multiplex set of six lobster specific primers, thereby allowing determination of both parental genotypes. Each female were kept separately during hatching, and the offspring were later mixed and raised in a communal rearing system. The early-larval survival was estimated at stage IV (bottom stage), and the survivors were identified to family and group by microsatellite profiling. Five different communal experiments were conducted, representing offspring from 65 berried females. Of the surviving larvae, 6.3% could not be assigned to family due to degraded DNA and no PCR amplification. Significant differences in early survival between offspring of wild and cultured origin were found in the experiments. No differences between the groups were found in stage IV larval size. Based on the pooled data on survival (as a measure of early larvae fitness) offspring of cultured females displayed a relative fitness of 60% in comparison to offspring from wild females. Large variation in survival was also observed among families within the wild and cultured groups, suggesting a genetic component for these traits and a potential for selective breeding.

Counterbalancing forces in electromigration

In electromigration (EM) experiments on metallic wires, a flux of atoms can lead to motion of the centre of mass (COM) of the wire. Hence, it may be tempting to assume that the flow of current produces a net force on the wire as a whole. We point out, on the basis of known momentum-balance arguments, that the net force on a metallic wire due to a passing steady-state current is zero. This is possible, because in addition to EM driving forces, acting on scattering centres, there are counterbalancing forces, acting on the rest of the system. Drift of the COM in EM experiments occurs inevitably because the substrate keeps the crystal lattice of the wire fixed, while allowing diffusion of defects in the bulk of the wire. This drift is not evidence for a net force on the wire.

Non-linear conductance of disordered quantum wires

The self-consistent electron potential in a current-carrying disordered quantum wire is spatially inhomogeneous due to the formation of resistivity dipoles across scattering centres. In this paper it is argued that these inhomogeneities in the potential result in a suppression of the differential conductance of such a wire at finite applied voltage. A semi-classical argument allows this suppression, quadratic in the voltage, to be related directly to the amount of intrinsic defect scattering in the wire. This result is then tested against numerical calculations.

Electromigration of vacancies in copper

The total current-induced force on atoms in a Cu wire containing a vacancy are calculated using the self consistent one-electron density matrix in the presence of an electric current, without separation into electron-wind and direct forces. By integrating the total current-induced force, the change in vacancy migration energy due to the current is calculated. We use the change in migration energy with current to infer an effective electromigration driving force F-e. Finally, we calculate the proportionality constant rho* between F-e and the current density in the wire.

Current-induced forces in atomic-scale conductors

We present a self-consistent tight-binding formalism to calculate the forces on individual atoms due to the flow of electrical current in atomic-scale conductors. Simultaneously with the forces, the method yields the local current density and the local potential in the presence of current flow, allowing a direct comparison between these quantities. The method is applicable to structures of arbitrary atomic geometry and can be used to model current-induced mechanical effects in realistic nanoscale junctions and wires. The formalism is implemented within a simple Is tight-binding model and is applied to two model structures; atomic chains and a nanoscale wire containing a vacancy.

Reinforced Stone Columns in Weak Deposits – A Laboratory Model Study

This paper investigates the performance of stone columns in a weak deposit such as peat. It evaluates the effects of reinforcing stone columns by jacketing with a tubular wire mesh and bridging reinforcement with a metal rod and a concrete plug. A series of plate loading tests was conducted on isolated stone columns installed in a soil bed consisting of a peat layer sandwiched between two layers of sand. The load–displacement characteristics of footings supported by stone columns were investigated by applying load to a circular plate supported on: (a) untreated soil; (b) soil treated with stone columns; and (c) soil treated with stone columns reinforced with the above reinforcing techniques. The work has shown that the settlement characteristics of the soil can be improved by installing stone columns and that a significant enhancement in the load–settlement response is achieved when the columns are reinforced by the various methods.

Electrochemical synthesis and characterization of conducting polyparaphenylene using room-temperature melt as the electrolyte

Freestanding polyparaphenylene films were obtained on polymerization of benzene at potential of 1.2 V versus Al wire on substrates like platinum/transparent conducting glass as an anode. The electrolyte used was chloroaluminate room-temperature melt, which was prepared by intimate mixing of a 1:2 ratio of cetyl pyridinium chloride and anhydrous aluminum chloride to yield a viscous liquid. This liquid was miscible in all proportions with benzene and other aromatic hydrocarbons in all proportions at room temperature. The polyparaphenylene films deposited on platinum anode exhibited a prominent cyclic voltammetric peak at 0.7 V versus Al wire as reference electrode in chloroaluminate medium. The impedance spectra gave low charge transfer resistance. The diffused reflectance electronic spectra of the film gave the peaks at 386 nm and 886 nm. The PPP films showed electronic conductivity around 3–4 × 104 S/cm by four probe method under nitrogen atmosphere. The polymer was also characterized by IR spectra, thermal studies, and SEM studies.

Studies on polypyrrole film in room temperature melt

A bluish-black shining free standing polypyrrole film (PPy) of electronic conductivity 130 S cm-1 has been prepared by electrochemical oxidative polymerization of pyrrole on Pt/transparent glass conducting electrode resistance 15 O cm-1, using a room temperature melt as an electrolyte, composed of 1:3 stoichiometric ratio of cetyl pyridinium chloride and anhydrous aluminum chloride at 0.58 V versus Al wire as a reference electrode. The film possessed a charge transfer resistance of 132 O, and showed two absorption peaks at 457 and 1264 nm in the UV-vis–NIR diffused reflectance spectra. The morphology of the film was hexagonal. The potential step technique suggested a layered structure. This thin film can easily be peeled off from the electrode surface after three cycles and can be used for various applications like dissipation of electrostatic charge, battery electrode materials, solid electrolytic capacitor, electrochromic windows and displays, microactuators etc. It was also characterized by IR, thermal and SEM studies.

Dynamical simulation of inelastic quantum transport

A method for correlated quantum electron-ion dynamics is combined with a method for electronic open boundaries to simulate in real time the heating, and eventual equilibration at an elevated vibrational energy, of a quantum ion under current flow in an atomic wire, together with the response of the current to the ionic heating. The method can also be used to extract inelastic current voltage corrections under steady-state conditions. However, in its present form the open-boundary method contains an approximation that limits the resolution of current-voltage features. The results of the simulations are tested against analytical results from scattering theory. Directions for the improvement of the method are summarized at the end.

The influence of compliant surfaces on bypass transition', Experiments in Fluids

The objective of the work was to investigate the effect of compliant surfaces on the receptivity and bypass transition of a boundary layer. Hot wire measurements in the pre-transitional and transitional boundary layers on nine different compliant and one rigid surface with identical geometries were made. The experiments were conducted in air and the compliant surfaces were manufactured from gelatine covered by a 10 lm protective PVC film. The laminar boundary layer profiles and growth rate results were the same for all the surfaces. However, the receptivity of the laminar boundary layer to freestream disturbances increased close to the leading edge of each compliant surface. Further downstream the majority of the compliant surfaces were successful in reducing the receptivity to a value below that for the rigid surface. The transition onset position on the compliant surfaces ranged from 3% downstream to 20% upstream of the rigid surface position. It was concluded that compliant surfaces with optimum properties can reduce receptivity and delay transition.