The effect of ionization on the populations of excited levels of C IV and C V in tokamak edge plasmas

The main populating and depopulating mechanisms of the excited energy levels of ions in plasmas with densities <10²³-10²⁴ m^-3 are electron collisional excitation from the ion's ground state and radiative decay, respectively, with the majority of the electron population being in the ground state of the ionization stage. Electron collisional ionization is predominately expected to take place from one ground state to that of the next higher ionization stage. However, the question arises as to whether, in some cases, ionization can also affect the excited level populations. This would apply particularly to those cases involving transient events such as impurity influxes in a laboratory plasma. An analysis of the importance of ionization in populating the excited levels of ions in plasmas typical of those found in the edge of tokamaks is undertaken for the C IV and C V ionization stages. The emphasis is on those energy levels giving rise to transitions of most use for diagnostic purposes (n ≤ 5). Carbon is chosen since it is an important contaminant of JET plasmas; it was the dominant low Z impurity before the installation of the ITER-like wall and is still present in the plasma after its installation. Direct electron collisional ionization both from and to excited levels is considered. Distorted-wave flexible atomic code calculations are performed to generate the required ionization cross sections, due to a lack of atomic data in the literature. Employing these data, ionization from excited level populations is not found to be significant in comparison with radiative decay. However, for some energy levels, ionization terminating in the excited level has an effect in the steady-state of the order of the measurement errors (±10%). During transient events, ionization to excited levels will be of more importance and must be taken into account in the calculation of excited level populations. More accurate atomic data, including possible resonance contributions to the cross sections, would tend to increase further the importance of these effects. 

Energy levels, radiative rates and electron impact excitation rates for transitions in Be-like Ti XIX

We report calculations of energy levels, radiative rates and electron impact excitation cross sections and rates for transitions in Be-like Ti XIX. The general-purpose relativistic atomic structure package is adopted for calculating energy levels and radiative rates. For determining the collision strengths and subsequently the excitation rates, the Dirac atomic R-matrix code (darc) is used. Oscillator strengths, radiative rates and line strengths are reported for all E1, E2, M1 and M2 transitions among the lowest 98 levels of the n≤ 4 configurations. Additionally, theoretical lifetimes are listed for all 98 levels. Collision strengths are averaged over a Maxwellian velocity distribution and the effective collision strengths obtained listed over a wide temperature range up to 10 ^7.7K. Comparisons are made with similar data obtained from the flexible atomic code (fac) to highlight the importance of resonances, included in calculations with darc, in the determination of effective collision strengths. Discrepancies between the collision strengths from darc and fac, particularly for forbidden transitions, are also discussed. 

Energy levels, radiative rates and electron impact excitation rates for transitions in He-like Ti XXI, v XXII, Cr XXIII and Mn XXIV

We report calculations of energy levels, radiative rates and electron impact excitation cross sections and rates for transitions in He-like Ti XXI, V XXII, Cr XXIII and Mn XXIV. grasp (general-purpose relativistic atomic structure package) is adopted for calculating energy levels and radiative rates. For determining the collision strengths and subsequently the excitation rates, the Dirac atomic R-matrix code (darc) is used. Oscillator strengths, radiative rates and line strengths are reported for all E1, E2, M1 and M2 transitions among the lowest 49 levels of each ion. Additionally, theoretical lifetimes are listed for all the 49 levels of the above four ions. Collision strengths are averaged over a Maxwellian velocity distribution and the effective collision strengths obtained listed over a wide temperature range up to 10 ^7.5K. Comparisons are made with similar data obtained using the flexible atomic code (fac) to highlight the importance of resonances, included in calculations with darc, in the determination of effective collision strengths. Discrepancies between the collision strengths from darc and fac, in particular for forbidden transitions, are also discussed. Finally, discrepancies between the present results for effective collision strengths with the darc code and earlier semi-relativistic R-matrix data are noted over a wide range of electron temperatures for many transitions in all ions. 

The View from the Edge: The Proyecto Arqueológico Chihuahua (PAC) 1990 to 2010: An Overview

The work of the Proyecto Arqueológico Chihuahua (PAC) has played an integral role in defining the origins and characteristics of the Chihuahua culture area, also known as the Casas Grandes Regional System. PAC has developed a critical suite of radiocarbon dates for the southern zone, undertaken the first substantial investigations of the Viejo period (ca. A.D. 800textendash1200 or 1250) since the early 1960s, and added to knowledge of the southern Medio period (ca. A.D. 1250textendash1450). The project has also elucidated the chronology, settlement patterns, subsistence strategies, and technology for both periods. Results of our research indicate continuity between the Viejo period, characterized by small pithouse settlements, and the pueblo focused Medio period in the southern zone, with some poorly understood external influences from both western Mesoamerica to the south and the American Southwest to the north shaping events within the area.

FEM Analysis to Optimally Design End Mill cutters for Milling of Ti-6Al-4V

This paper presents an FEM analysis conducted for optimally designing end mill cutters through verifying the cutting tool forces and stresses for milling Titanium alloy Ti-6Al-4 V. Initially, the theoretical tool forces are calculated by considering the cutting edge on a cutting tool as the curve of an intersection over a spherical/flat surface based on the model developed by Lee & Altinas [1]. Considering the lowest tool forces the cutting tool parameters are taken and optimal design of end mill is decided for different sizes. Then the 3D CAD models of the end mills are developed and used for Finite Element Method to verify the cutting forces for milling Ti-6Al-4 V. The cutting tool forces, stress, strain concentration (s), tool wear, and temperature of the cutting tool with the different geometric shapes are simulated considering Ti-6Al-4 V as work piece material. Finally, the simulated and theoretical values are compared and the optimal design of cutting tool for different sizes are validated. The present approach considers to improve the quality of machining surface and tool life with effects of the various parameters concerning the oblique cutting process namely axial, radial and tangential forces. Various simulated test cases are presented to highlight the approach on optimally designing end mill cutters.

Enhanced durability of Li-O2 batteries employing vertically standing Ti nanowire array supported cathodes

Ti nanowire arrays vertically standing on Ti foam prepared by a facile corrosion method were used as self-supported Li-O₂ battery cathodes. The batteries exhibited enhanced durability at high rate current densities (e.g. cycling 640 times at 5 A g^-1).