Hyperpolarisation-activated inward current in isolated sheep mesenteric lymphatic smooth muscle.

1. Freshly isolated sheep lymphatic smooth muscle cells were studied using the perforated patch-clamp technique. Hyperpolarisation with constant-current pulses caused a time-dependent rectification evident as a depolarising 'sag' followed by an anode-break overshoot at the end of the pulse. Both sag and overshoot were blocked with 1 mM Cs+. 2. Cells were voltage clamped at -30 mV and stepped to -120 mV in 10 mV steps of 2 s duration. Steps negative to -60 mV evoked a slowly activating, non-inactivating inward current which increased in size and rate of activation with increasing hyperpolarisation. 3. The slowly activating current was reduced in Na+-free bathing solution but enhanced when the extracellular K+ concentration was increased to 60 mM. The current was significantly reduced by 1 mM Cs+ and 1 microM ZD7288 but not by 1.8 mM Ba2+. 4. The steady-state activation curve of the underlying conductance showed a threshold at -50 mV and half-maximal activation at -81 mV. Neither threshold nor half-maximal activation was significantly affected by increasing the external K+ concentration to 60 mM. 5. The frequency of spontaneous contractions and fluid propulsion in isolated cannulated segments of sheep mesenteric lymphatics were decreased by 1 mM Cs+ and by 1 microM ZD7288. 6. We conclude that sheep lymphatics have a hyperpolarisation-activated inward current similar to the If seen in sinoatrial node cells of the heart. Blockade of this current slows spontaneous pumping in intact lymphatic vessels suggesting that it is important in normal pacemaking.

A Tunable Split Resonator Method for Non-destructive Permittivity Characterization

The split cylinder resonator method is improved for nondestructive and accurate measurement for low permittivity materials at multiple frequency points. The dielectric constants of flat substrate materials are calculated based on a rigorous mode match analysis of the TE/sub 011/ mode. The loss tangent is also approximately calculated. The dielectric properties of two commercial substrates have been measured at multiple frequencies. The results demonstrate that this technology is capable of accurately characterizing the dielectric properties of flat substrate materials versus frequency in a nondestructive way.

Escape times for rigid Brownian rotators in a bistable potential from the time evolution of the Green function and the characteristic time of the probability evolution

The greatest relaxation time for an assembly of three- dimensional rigid rotators in an axially symmetric bistable potential is obtained exactly in terms of continued fractions as a sum of the zero frequency decay functions (averages of the Legendre polynomials) of the system. This is accomplished by studying the entire time evolution of the Green function (transition probability) by expanding the time dependent distribution as a Fourier series and proceeding to the zero frequency limit of the Laplace transform of that distribution. The procedure is entirely analogous to the calculation of the characteristic time of the probability evolution (the integral of the configuration space probability density function with respect to the position co-ordinate) for a particle undergoing translational diffusion in a potential; a concept originally used by Malakhov and Pankratov (Physica A 229 (1996) 109). This procedure allowed them to obtain exact solutions of the Kramers one-dimensional translational escape rate problem for piecewise parabolic potentials. The solution was accomplished by posing the problem in terms of the appropriate Sturm-Liouville equation which could be solved in terms of the parabolic cylinder functions. The method (as applied to rotational problems and posed in terms of recurrence relations for the decay functions, i.e., the Brinkman approach c.f. Blomberg, Physica A 86 (1977) 49, as opposed to the Sturm-Liouville one) demonstrates clearly that the greatest relaxation time unlike the integral relaxation time which is governed by a single decay function (albeit coupled to all the others in non-linear fashion via the underlying recurrence relation) is governed by a sum of decay functions. The method is easily generalized to multidimensional state spaces by matrix continued fraction methods allowing one to treat non-axially symmetric potentials, where the distribution function is governed by two state variables. (C) 2001 Elsevier Science B.V. All rights reserved.

An exactly solvable four transition point model

Heavy particle collisions, in particular low-energy ion-atom collisions, are amenable to semiclassical JWKB phase integral analysis in the complex plane of the internuclear separation. Analytic continuation in this plane requires due attention to the Stokes phenomenon which parametrizes the physical mechanisms of curve crossing, non-crossing, the hybrid Nikitin model, rotational coupling and predissociation. Complex transition points represent adiabatic degeneracies. In the case of two or more such points, the Stokes constants may only be completely determined by resort to the so-called comparison- equation method involving, in particular, parabolic cylinder functions or Whittaker functions and their strong-coupling asymptotics. In particular, the Nikitin model is a two transition-point one-double-pole problem in each half-plane corresponding to either ingoing or outgoing waves. When the four transition points are closely clustered, new techniques are required to determine Stokes constants. However, such investigations remain incomplete, A model problem is therefore solved exactly for scattering along a one-dimensional z-axis. The energy eigenvalue is b(2)-a(2) and the potential comprises -z(2)/2 (parabolic) and -a(2) + b(2)/2z(2) (centrifugal/centripetal) components. The square of the wavenumber has in the complex z-plane, four zeros each a transition point at z = +/-a +/- ib and has a double pole at z = 0. In cases (a) and (b), a and b are real and unitarity obtains. In case (a) the reflection and transition coefficients are parametrized by exponentials when a(2) + b(2) > 1/2. In case (b) they are parametrized by trigonometrics when a(2) + b(2) <1/2 and total reflection is achievable. In case (c) a and b are complex and in general unitarity is not achieved due to loss of flux to a continuum (O'Rourke and Crothers, 1992 Proc. R. Sec. 438 1). Nevertheless, case (c) coefficients reduce to (a) or (b) under appropriate limiting conditions. Setting z = ht, with h a real constant, an attempt is made to model a two-state collision problem modelled by a pair of coupled first-order impact parameter equations and an appropriate (T) over tilde-tau relation, where (T) over tilde is the Stueckelberg variable and tau is the reduced or scaled time. The attempt fails because (T) over tilde is an odd function of tau, which is unphysical in a real collision problem. However, it is pointed out that by applying the Kummer exponential model to each half-plane (O'Rourke and Crothers 1994 J. Phys. B: At. Mel. Opt. Phys. 27 2497) the current model is in effect extended to a collision problem with four transition points and a double pole in each half-plane. Moreover, the attempt in itself is not a complete failure since it is shown that the result is a perfect diabatic inelastic collision for a traceless Hamiltonian matrix, or at least when both diagonal elements are odd and the off-diagonal elements equal and even.

Perovskite lead zirconium titanate nanorings: Towards nanoscale ferroelectric

Rings of perovskite lead zirconium titanate (PZT) with internal diameters down to similar to 5 nm and ring thicknesses of similar to 5-10 nm have been fabricated and structurally, crystallographically, and chemically characterized using an analytical transmission electron microscope. Ring fabrication involved conformal solution deposition of a thin layer of PZT on the inside of a thin film of anodized aluminum oxide nanopores, and subsequent sectioning of the coated pores perpendicular to their cylinder axes. Although the starting solution used for the solution deposition was made from morphotropic phase boundary PZT, the nanorings were found to be on the zirconium-rich side of the PZT phase diagram. Nevertheless, coatings were found to be of perovskite crystallography. The dimensions of these nanorings are such that they have the potential to demonstrate polarization vortices, as modeled by Naumov [Nature (London) 432, 737 (2004)], and moreover represent the perfect morphology to allow vortex alignment and the creation of the ferroelectric "solenoid" as modeled by Gorbatsevich and Kopaev [Ferroelectrics 161, 321 (1994)].

Effects of the stockperson on dairy cow behaviour and milk yield

The relationship between stockperson behaviour, measured as verbal and physical interactions with the dairy cows (no. ¼ 210), during milking and the subsequent milk yield obtained was examined. The numbers of steps and kicks made by the cows during milking was recorded. The behaviour of two stockteams, each consisting of two stockmen, were recorded over 10 weekend sessions. The two teams varied in the types of interactions and when the stockteam that performed more positive interactions worked with the cows (team A), the cows had a significantly higher milk yield (P , 0·05) although this difference was small (17·54 v. 17·44 kg). When team A was milking the cows also stepped and kicked on the platform significantly more ( P , 0·05) compared with team B. The results also indicated that while each stockteam tended to interact with the same cows each session, different stockpersons interacted with different cows. These findings highlight the importance of the role of the stockperson in milk output and dairy cow behaviour in a commercial setting.

Experimental investigation into the temperature and heat transfer distribution around air-cooled cylinders

This paper describes an experimental investigation into the surface heat transfer coefficient of finned metal cylinders in a free air stream. Ten cylinders were tested with four different fin pitches and five different fin lengths. The cylinders and their fins were designed to be representative of those found on a motorcycle engine with an external cylinder diameter of 100 mm and fin lengths of 10 to 50 mm. The fins of each cylinder were gravity die cast in aluminum allow. Each cylinder was electrically heated and mounted in a wind tunnel which subjected it to a range of air speeds between 2 and 20 m/s. The surface heat transfer coefficient, h, was found primarily to be a function of the air speed and the fin separation, with fin length having a lesser effect. In addition to the determination of an overall heat transfer coefficient, the distribution of cooling around the circumference of each cylinder was also studied. Not surprisingly, the cooling was found to be greatest on the front of the cylinder, which was the side first impinged by the air stream. The cooling of the rear of the cylinder was better than might have been expected and this is quantified.

Influence of mix proprtions on rheolgy of cement grouts containing limestone powder

In this paper the parameters of cement grout affecting rheological behaviour and compressive strength are investigated. Factorial experimental design was adopted in this investigation to assess the combined effects of the following factors on fluidity, rheological properties, induced bleeding and compressive strength: water/binder ratio (W/B), dosage of superplasticiser (SP), dosage of viscosity agent (VA), and proportion of limestone powder as replacement of cement (LSP). Mini-slump test, Marsh cone, Lombardi plate cohesion meter, induced bleeding test, coaxial rotating cylinder viscometer were used to evaluate the rheology of the cement grout and the compressive strengths at 7 and 28 days were measured. A two-level fractional factorial statistical model was used to model the influence of key parameters on properties affecting the fluidity, the rheology and compressive strength. The models are valid for mixes with 0.35-0.42 W/B, 0.3-1.2% SP, 0.02-0.7% VA (percentage of binder) and 12-45% LSP as replacement of cement. The influences of W/B, SP, VA and LSP were characterised and analysed using polynomial regression which can identify the primary factors and their interactions on the measured properties. Mathematical polynomials were developed for mini-slump, plate cohesion meter, inducing bleeding, yield value, plastic viscosity and compressive strength as function of W/B, SP, VA and proportion of LSP. The statistical approach used highlighted the limestone powder effect and the dosage of SP and VA on the various rheological characteristics of cement grout

A DFT study of the chain growth probability in Fischer-Tropsch synthesis

The chain growth probability (alpha value) is one of the most significant parameters in Fischer-Tropsch (FT) synthesis. To gain insight into the chain growth probability, we systematically studied the hydrogenation and C-C coupling reactions with different chain lengths on the stepped Co(0001) surface using density functional theory calculations. Our findings elucidate the relationship between the barriers of these elementary reactions and the chain length. Moreover, we derived a general expression of the chain growth probability and investigated the behavior of the alpha value observed experimentally. The high methane yield results from the lower chain growth rate for C-1 + C-1 coupling compared with the other coupling reactions. After C-1, the deviation of product distribution in FT synthesis from the Anderson-Schulz-Flory distribution is due to the chain length-dependent paraffin/olefin ratio. (C) 2008 Elsevier Inc. All rights reserved.

Chain growth mechanism in Fischer-Tropsch synthesis: A DFT study of C-C coupling over Ru, Fe, Rh, and Re surfaces

A quantitative approach is used to understand the chain growth mechanism in FT synthesis on the Ru, Fe, Rh, and Re surfaces. The C-C coupling reactions are extensively calculated on the stepped metal surfaces. Combining the coupling barriers and reactant stabilities, we investigate the reaction rates of all possible C, + C-1 coupling pathways on the metal surfaces. It is found that (i) all the transition-state structures are similar on these surfaces, while some coupling barriers are very different; (ii) the dominant chain growth pathways on these surfaces are different: C + CH and CH + CH on Rh and Ru surfaces, C + CH3 on Fe surface, and C + CH on Re surface. The common features of the major coupling reactions together with those on the Co surface are also discussed.

First-principles study of oxygenates on Co surfaces in Fischer-Tropsch synthesis

Extensive density function theory calculations are performed to study the mechanism of the formation of aldehyde and alcohol on Co surfaces in Fischer-Tropsch synthesis, a challenging issue in heterogeneous catalysis. Three possible pathways for the production of formaldehyde and methanol on flat and stepped Co(0001) surfaces are investigated: (i) CO + 4H -> CHO + 3H -> CH2O + 2H -> CH3O + H -> CH3OH; (ii) CO + 4H -> COH + 3H -> CHOH + 2H -> CH2OH + H -> CH3OH; and (iii) the coupling reactions of CH2 + O -> CH2O and CH3 + OH -> CH3OH. It is found that these pathways are generally favored at step sites, and the preferred mechanism is pathway (i) via CHO. Furthermore, the three traditional chain growth mechanisms in Fischer-Tropsch synthesis are semi quantitatively compared and discussed. Our results suggest that the two mechanisms involving oxygenate intermediates (the CO-insertion and hydroxycarbene mechanisms) are less important than the carbene mechanism in the production of long chain hydrocarbons. However, the CO-insertion mechanism may be responsible for the production of long-chain oxygenates.

CHx hydrogenation on Co(0001): A density functional theory study

Hydrogenation is an important process in the Fischer-Tropsch synthesis. In this work, all the elementary steps of the hydrogenation from C to CH4 are studied on both flat and stepped Co(0001) using density functional theory (DFT). We found that (i) CH3 hydrogenation (CH3+H-->CH4) is the most difficult one among all the elementary reactions on both surfaces, possessing barriers of around 1.0 eV; (ii) the other elementary reactions have the barriers below 0.9 eV on the flat and stepped surfaces; (iii) CH2 is the least stable species among all the CHx(x=1-3) species on both surfaces; and (iv) surface restructuring may have little effect on the CHx(x=0-3) hydrogenation. The barriers of each elementary step on both flat and stepped surfaces are similar and energy profiles are also similar. The reason as to why CHx hydrogenation is not structure-sensitive is also discussed. (C) 2005 American Institute of Physics.

A density functional theory study on the water formation at high coverages and the water effect in the Fischer-Tropsch synthesis

The O removal through water formation is an important process in the Fischer-Tropsch synthesis. In this study, both steps in water formation (O + H --> OH, OH + H --> H2O) are studied on the stepped Co(0001) at high coverages using density functional theory. We find the following. (i) In both O-O and O-OH co-adsorption systems, two transition states (TSs) were located for the O hydrogenation: in one TS, both O and H are on the same terrace, and in the other they are at the interface between the step edge and the terrace below. (ii) In both the O-O and O-OH co-adsorption systems, the O hydrogenation at the interface is easier (E-a = 0.32 eV in the O-O system, E-a = 1.10 eV in the O-OH system) than that on the same terrace (E-a = 1.49 eV in the O-O system, E-a = 1.80 eV in the O-OH system). (iii) In both the O-O and O-OH co-adsorption systems, only one TS for the OH hydrogenation was located, in which both OH and H are on the same terrace. (iv) Compared to the OH hydrogenation in the O-OH system (E-a = 1.46 eV), the reaction in the OH-OH system (E-a = 0.64 eV) is much easier. The barrier differences and the water effect on the Fischer-Tropsch synthesis are discussed. A possible route with low barriers for water formation is proposed.

CO dissociation and O removal on Co(0001): a density functional theory study

CO dissociation and O removal (water formation) are two important processes in the Fischer-Tropsch synthesis. In this study, both processes are studied on the flat and stepped Co(0 0 0 1) using density functional theory. It is found that (i) it is difficult for CO to dissociate on the flat Co(0 0 0 1) due to the high barrier of 1.04 eV relative to the CO molecule in the gas phase; (ii) the stepped Co(0 0 0 1) is much more favoured for CO dissociation; (iii) the first step in water formation, O + H --> OH, is unlikely to occur on the flat Co(0 0 0 1) due to the high barrier of 1.72 eV, however, this reaction can become feasible on steps where the barrier is reduced to 0.73 eV; and (iv) the barrier in the second step, OH + H --> H2O, on steps is higher than that on the flat surface. (C) 2004 Elsevier B.V. All rights reserved.

A density functional theory study of stepwise addition reactions in ammonia synthesis on Ru(0001)

To shed light on stepwise addition reactions in ammonia synthesis, density functional theory calculations are carried out to investigate NHx (x = 1-3) formation on Ru(0001). The reactions on a flat surface are first examined. Transition states and reaction barriers are determined. It is found that the reaction barriers for these stepwise addition reactions are rather high. For example, the barrier for NH hydrogenation is calculated to be 1.28 eV, which is comparable with that of N-2 dissociation. One of the stepwise addition reactions, NH + H --> NH2, on a stepped surface is also considered. Interestingly, the reaction barrier is found to be significantly lower than that on the flat surface, but is considerably higher than that of N-2 dissociation on the same stepped surface. In addition, the coverage effect on the reaction energetics is also addressed. (C) 2001 Published by Elsevier Science B.V.