Preparation and characterization of Poly(vinyl alcohol) nanocomposites made from cellulose nanofibers

A method using a combination of ball milling, acid hydrolysis, and ultrasound was developed to obtain a high yield of cellulose nanofibers from flax fibers and microcrystalline cellulose (MCC). Poly(vinyl alcohol) (PVA) nanocomposites were prepared with these additives by a solution-casting technique. The cellulose nanofibers and nanocomposite films that were produced were characterized with Fourier transform infrared spectrometry, X- ray diffraction, thermogravimetric analysis, scanning electron microscopy, and transmission electron microscopy. Nanofibers derived from MCC were on average approximately 8 nm in diameter and 111 nm in length. The diameter of the cellulose nanofibers produced from flax fibers was approximately 9 nm, and the length was 141 nm. A significant enhancement of the thermal and mechanical properties was achieved with a small addition of cellulose nanofibers to the polymer matrix. Interestingly, the flax nanofibers had the same reinforcing effects as MCC nanofibers in the matrix. Dynamic mechanical analysis results indicated that the use of cellulose nanofibers (acid hydrolysis) induced a mechanical percolation phenomenon leading to outstanding and unusual mechanical properties through the formation of a rigid filler network in the PVA matrix. X-ray diffraction showed that there was no significant change in the crystallinity of the PVA matrix with the incorporation of cellulose nanofibers. © 2009 Wiley Periodicals, Inc.

Rheological Evaluation of the Isothermal Cure Characteristics of Medical Grade Silicone Elastomers

Silicone elastomer systems have been shown to offer potential for the fabrication of medical devices and sustained release drug delivery devices comprising low molecular weight drugs and protein therapeutics. For drug delivery systems in particular, there is often no clear rationale for selection of the silicone elastomer grade, particularly in respect of optimizing the manufacturing conditions to ensure thermal stability of the active agent and short cycle times. In this study, the cure characteristics of a range of addition-cure and condensation-cure, low-consistency, implant-grade silicone elastomers, either as supplied or loaded with the model protein bovine serum albumin (BSA) and the model hydrophilic excipient glycine, were investigated using oscillatory rheology with a view to better understanding the isothermal cure characteristics. The results demonstrate the influence of elastomer type, cure temperature, protein loading, and glycine loading on isothermal cure properties. By measuring the cure time required to achieve tan delta values representative of early and late-stage cure conditions, a ratio t(1)/t(2) was defined that allowed the cure characteristics of the various systems to be compared. Sustained in vitro release of BSA from glycine-loaded silicone elastomer covered rod devices was also demonstrated over 14 days. (C) 2010 Wiley Periodicals, Inc. J Appl Polym Sci 116: 2320-2327, 2010

USE OF RETRODIRECTIVE ARRAY PHASE CONJUGATION CIRCUITRY FOR NEAR- AND FAR-FIELD POSITION ANGLE OF ARRIVAL DETECTION

In this article, we present position indication functionality as obtained by using a retrodirective array, thereby allowing location information extraction of the position of the remote transmitter with which the retrodirective array is cooperating. This is carried out using straightforward circuitry with no requirement for complex angle of arrival algorithms, thereby giving a result in real time enabling tracking of fast moving transmitters. We show using a 10 x element retrodirective array, operating at 2.4 GHz that accuracies of far-field angle of arrival of within +/- 1 degrees over the arrays +/- 30 degrees azimuth field of view are possible. While in the near-field for angles of arrival of +/- 10 degrees it is possible to extract the position of a dipole source down to a resolution of 032 lambda. (C) 2010 Wiley Periodicals, Inc. Microwave Opt Technol Lett 52: 1031-1034, 2010; Published online in Wiley InterScience (www.interscience.wiley.com). DOI 10.1002/mop.25097

RCS CONTROL USING CASCADED CIRCULARLY POLARIZED FREQUENCY SELECTIVE SURFACES AND AN AMC STRUCTURE AS A SWITCHABLE TWIST POLARIZER

This article presents a cascaded arrangement comprising a double-layer frequency selective surface circularly polarizing (CPFSS) and a second screen that can be switched between artificial magnetic conduction (AMC) or perfect electric conducting. (PEC) states. The CPFSS consists of two stacked aluminium sheets patterned with periodic split ring structures While the AMC is a PCB sheet patterned with metallic squares interconnected by links By either open or short circuiting these links it is shown that the cascade of screens can be made to twist, or not to twist, an incident 45 degrees linearly polirized signal through 90 degrees upon reflection from the assembly The system was designed and optimized using CST software and predictions were validated experimentally and measured monostatic reflection loss results (C) 2010 Wiley Periodicals, Inc Microwave Opt Technol Lett 52 577-580, 2010. Published online in Wiley InterScience (www.interscience.wiley.com) DOI 10.1002/mop.24979

Validation of the CDC Biofilm Reactor as a Dynamic Model for Assessment of Encrustation Formation on Urological Device Materials

Contemporary medical science is reliant upon the rational selection and utilization of devices, and therefore, an increasing need has developed for in vitro systems aimed at replicating the conditions to which urological devices will be subjected to during their use in vivo. We report the development and validation of a novel continuous flow encrustation model based on the commercially available CDC biofilm reactor. Proteus mirabilis-induced encrustation formation on test biomaterial sections under varying experimental parameters was analyzed by X-ray diffraction, infrared- and Raman spectroscopy and by scanning electron microscopy. The model system produced encrusted deposits similar to those observed in archived clinical samples. Results obtained for the system are highly reproducible with encrustation being rapidly deposited on test biomaterial sections. This model will have utility in the rapid screening of encrustation behavior of biomaterials for use in urological applications. (C) 2010 Wiley Periodicals. Inc. J Biomed Mater Res Part B: Appl Biomater 93B: 128-140, 2010

Germanium bonding to AI2O3

Germanium has been bonded to both single crystal Al2O 3 (sapphire) as well as fine grain Al2O3. A germanium to sapphire bonding energy of 3 J/m2 has been measured after a 200 °C bond anneal. Micro voids formed between the germanium/sapphire interface can be removed by employing an interfacial layer of silicon dioxide on either surface. Patterning the sapphire into a grid pattern prior to bonding creates an escape path for trapped gas or moisture allowing micro void free direct bonding to be achieved. Modifying the surface of the fine grain Al2O3 surface with a polycrystalline silicon deposition and polish creates a surface, having an rms roughness (measured over a 250© m2 area), of 1.5nm, suitable for bonding. Techniques employed in the germanium sapphire bonding can then be used in the bonding of fine grain A12O3 to germanium. © The Electrochemical Society.

Primum non nocere, czyli uwagi warsztatowe

Primum non nocere or comments on the workshop: a case study This article provides a detailed analysis of the Polish translation of a manual of homiletics against the background of the broader question regarding the translator’s workshop. The various translational solutions are subsequently discussed in sections devoted to grammatical and lexical errors, metaphorical and terminological incoherence, and collocational and stylistic errors. It is suggested that the deficient workshop of the translator manifested in numerous errors, chiefly attributable to insufficient understanding of the source language by the translator, may correspond to the quasi-theological conviction according to which the crucial characteristic of the translator is the passion rather than linguistic competence. The article ends with the appeal to translators of various texts – not just theological ones – to observe the ancient principle of primum non nocere in order to ensure the acceptable quality of their works.

Dielectric constant characterization using a numerical method for the microstrip ring resonator

A new method of dielectric-constant measurement is developed. The dielectric constant epsilon(r) RF/microwave substrate is extracted by combining the microstrip ring resonator measurement with Ansoft HFSS electromagnetic simulation software. The developed method has two advantages: (i) characterization of dielectric constant versus multiple frequency points, and (ii) compatibility with electronics design automation (EDA) software tools. This characterization method can reduce the design cycle of microwave circuits and devices. (C) 2004 Wiley Periodicals, Inc.

The Reception of Byzantium in European Culture since 1500

Studies on the reception of the classical tradition are an indispensable part of classical studies. Understanding the importance of ancient civilization means also studying how it was used subsequently. This kind of approach is still relatively rare in the field of Byzantine Studies. This volume, which is the result of the range of interests in (mostly) non-English-speaking research communities, takes an important step to filling this gap by investigating the place and dimensions of ‘Byzantium after Byzantium’.
This collection of essays uses the idea of ‘reception-theory’ and expands it to show how European societies after Byzantium have responded to both the reality, and the idea of Byzantine Civilisation. The authors discuss various forms of Byzantine influence in the post-Byzantine world from architecture to literature to music to the place of Byzantium in modern political debates (e.g. in Russia). The intentional focus of the present volume is on those aspects of Byzantine reception less well-known to English-reading audiences, which accounts for the inclusion of Bulgarian, Czech, Polish and Russian perspectives. As a result this book shows that although so-called 'Byzantinism' is a pan-European phenomenon, it is made manifest in local/national versions.
The volume brings together specialists from various countries, mainly Byzantinists, whose works focus not only on Byzantine Studies (that is history, literature and culture of the Byzantine Empire), but also on the influence of Byzantine culture on the world after the Fall of Constantinople.

Genetic diversity of liver flukes (Fasciola hepatica) from Eastern Europe.

The genetic diversity of liver fluke populations in three different countries from Eastern Europe (Greece, Bulgaria, and Poland) in comparison with available data from other countries was determined. Specifically, SNPs from regions of two nuclear genes, 28S rDNA, ß-tubulin 3 and an informative region of the mitochondrial genome were examined. Two major lineages for the 28S rDNA gene based on the highly polymorphic 105th nucleotide position were found. These lineages were widely and almost equally spread not only through the countries studied but also in other investigated geographical areas. Two basic lineages and additional haplotypes were defined for the mtDNA gene region, consisting of the cytochrome c oxidase subunit III gene, transfer RNA histidine gene and cytochome b gene. The basic lineages were observed within Greek, Bulgarian, and Polish Fasciola hepatica populations but the distribution of additional haplotypes differed between the populations from the three countries. For the ß-tubulin 3 gene multiple polymorphic sites were revealed but no explicit clades. The SNPs were spread unequally in all studied geographical regions with an evident distinction between the Greek and Polish specimens. Additional genotypes for the 28S rDNA region as well as haplotypes of the mtDNA region that were typical for the Greek or Polish populations were observed. Significant polymorphisms for ß-tubulin 3 gene were displayed with decreasing percentage of presence within populations from Greece to Poland. There was an amino acid substitution in ß-tubulin 3 protein found only among Polish specimens. It is hypothesized that genotypic differences between Greek, Bulgarian, and Polish liver fluke populations are due to territorial division and genetic drift in past epochs.

Identifying Critical Financial Networks of the DJIA: Toward a Network-Based Index

The purpose of this article is twofold. First, we introduce a novel definition of financial networks obtained from time series data from the stock market. Second, we demonstrate that these networks can be used as an index with the property to reflect critical states of the market, respectively, crashes sufficiently. Our work aims to advocate a network-based analysis in the context of the stock market, because such a collective phenomenon can not only be economically described by networks but also analyzed as demonstrated in this article. (C) 2010 Wiley Periodicals, Inc. Complexity 16: 24-33, 2010

Effect of the incorporation of hydroxy-terminated liquid silicones on the cure characteristics, morphology, and release of a model protein from silicone elastomer-covered rods

Silicone elastomer systems have previously been shown to offer potential for the sustained release of protein therapeutics. However, the general requirement for the incorporation of large amounts of release enhancing solid excipients to achieve therapeutically effective release rates from these otherwise hydrophobic polymer systems can detrimentally affect the viscosity of the precure silicone elastomer mixture and its curing characteristics. The increase in viscosity necessitates the use of higher operating pressures in manufacture, resulting in higher shear stresses that are often detrimental to the structural integrity of the incorporated protein. The addition of liquid silicones increases the initial tan delta value and the tan delta values in the early stages of curing by increasing the liquid character (G '') of the silicone elastomer system and reducing its elastic character (G'), thereby reducing the shear stress placed on the formulation during manufacture and minimizing the potential for protein degradation. However, SEM analysis has demonstrated that if the liquid character of the silicone elastomer is too high, the formulation will be unable to fill the mold during manufacture. This study demonstrates that incorporation of liquid hydroxy-terminated polydimethylsiloxanes into addition-cure silicone elastomer-covered rod formulations can both effectively lower the viscosity of the precured silicone elastomer and enhance the release rate of the model therapeutic protein bovine serum albumin. (C) 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011

Fabrication and characterisation of high resistivity SOI substrates for monolithic high energy physics detectors

Silicon on Insulator (SOI) substrates offer a promising platform for monolithic high energy physics detectors with integrated read-out electronics and pixel diodes. This paper describes the fabrication and characterisation of specially-configured SOI substrates using improved bonded wafer ion split and grind/polish technologies. The crucial interface between the high resistivity handle silicon and the SOI buried oxide has been characterised using both pixel diodes and circular geometry MOS transistors. Pixel diode breakdown voltages were typically greater than 100V and average leakage current densities at 70 V were only 55 nA/ sq cm. MOS transistors subjected to 24 GeV proton irradiation showed an increased SOI buried oxide trapped charge of only 3.45x1011cn-2 for a dose of 2.7Mrad