Frequency selective surface using nested split ring slot elements as a lens with mechanically reconfigurable beam steering capability

The design is described of a double layer frequency selective surface which can produce a differential phase shift of 180 ° as the wave propagates through it at normal incidence. The hand of an applied circularly polarized signal is reversed due to the 180° phase shift, and it is demonstrated that the exit circularly polarized output signal can be phase advanced or phase retarded by 180 ° upon rotation of the elements comprising the structure. This feature allows the surface to act as a spatial phase shifter. In this paper the beam steering capabilities of a 10 × 10 array of such elements are demonstrated. Here the individual elements comprising the array are rotated relative to each other in order to generate a progressive phase shift. At normal incidence the 3 dB Axial Ratio Bandwidth for LHCP to RHCP conversion is 5.3% and the insertion loss was found to be -2.3 dB, with minimum axial ratio of 0.05 dB. This array is shown to be able to steer a beam from -40 ° to +40 ° while holding axial ratio at the pointing angle to below 4 dB. The measured radiation patterns match the theoretical calculation and full-wave simulation results. © 2010 IEEE.

Measurement of absolute charge-exchange cross sections for He2+ collisions with He and H-2

Reported are total, absolute charge-exchange cross sections for collisions of 3He(2+) ions with He and H-2. Measurements are reported at fixed energies between 0.33 and 4.67 keV/amu. Both the present results and earlier results of others are analyzed in terms of available experimental small-angle differential cross sections as a function of collision energy, and hence the geometry of the exit aperture of the gas-collision cells used by the various experimental groups. In addition, the effective length of gas-collision cells is studied using fluid dynamic and molecular flow simulations to address the density patterns near the cell entrance and exit apertures. When small acceptance-angle corrections were applied, the results of present and previous measurements for the single electron capture in these systems were brought into good accord in the relevant energy ranges. Taken in their entirety, the present data for 3He(2+) with He and H-2 lend themselves to new theoretical calculations of the multichannel charge-exchange cross sections.

Moving in and out of poverty - The impact of welfare regimes on poverty dynamics in the EU

Although many of the debates around social exclusion and cumulative disadvantage relate to processes that occur across time, there has been relatively little research into poverty dynamics except in a few notable countries such as Britain, the USA and Germany. This neglect is almost entirely because of the absence of comparative longitudinal data on income for other countries, but it is regrettable given the central importance of this area. By studying poverty dynamics we not only get a better insight into the processes leading to patterns of disadvantage and inequality, but we can also understand better the influence of different welfare state regimes on the social risks experienced by different types of individuals and households. The extent to which different national contexts protect their citizens from poverty persistence, or vary in the factors leading to poverty persistence, tells us a great deal about the workings of their socioeconomic systems and welfare regimes.

In this article we use the recent availability of five waves of the European Community Household Panel Survey to outline the nature of poverty persistence and poverty dynamics across a large number of countries. In doing so we ask three important questions. First, is poverty a more common experience when viewed longitudinally rather than cross-sectionally, and how is this affected by the income poverty line used? Second, can we identify a tendency toward poverty persistence, and does this vary in its extent across countries? Third and lastly, what types of events are more likely to lead to entry into and exit from poverty, and does the importance of these events differ between countries? The article shows that the experience of poverty is far wider than is appreciated from cross-sectional data, and also tends to be more concentrated on a particular population than would be expected from cross-sectional rates. Moreover, the pattern of poverty persistence is congruent with welfare regime theory. The importance of country institutions and welfare regimes is also underlined by the finding that social welfare and market incomes play different roles in poverty transitions across countries, and that Southern European, or residualist, welfare regimes focus poverty risks on the experience of the household's primary earner to a far greater extent than Northern European welfare states do.

Simulation of relativistically colliding laser-generated electron flows

The plasma dynamics resulting from the simultaneous impact, of two equal, ultra-intense laser pulses, in two spatially separated spots, onto a dense target is studied via particle-in-cell simulations. The simulations show that electrons accelerated to relativistic speeds cross the target and exit at its rear surface. Most energetic electrons are bound to the rear surface by the ambipolar electric field and expand along it. Their current is closed by a return current in the target, and this current configuration generates strong surface magnetic fields. The two electron sheaths collide at the midplane between the laser impact points. The magnetic repulsion between the counter-streaming electron beams separates them along the surface normal direction, before they can thermalize through other beam instabilities. This magnetic repulsion is also the driving mechanism for the beam-Weibel (filamentation) instability, which is thought to be responsible for magnetic field growth close to the internal shocks of gamma-ray burst jets. The relative strength of this repulsion compared to the competing electrostatic interactions, which is evidenced by the simulations, suggests that the filamentation instability can be examined in an experimental setting. (C) 2012 American Institute of Physics. [http://dx.doi.org/10.1063/1.4768426]

“Boundary-setting as a core activity in complex public systems”

Title: Boundary-setting as a core activity in complex public systems
Authors: Joanne Murphy & Mary Lee Rhodes

The definition of the boundary of a system is at the core of any systems approach (Midgley 2000; 2003). By defining boundaries we enable – and delimit – the range of outcomes sought and the actions and resources that can be brought to bear. In complex adaptive systems (CAS) analysis, the conceptualisaion and definition of boundaries is particularly challenging as they are constantly undergoing redefinition through agent action, interaction and entry/exit. (Rhodes et al 2011). The concept of ‘boundaries’ appears regularly in a wide range of literature around public management, administration, geopolitics, regeneration and organisational development. Discussions around boundaries focus on many things from concrete physical manifestations and barriers, to virtual interfaces between one organisational unit and another, or even entirely theoretical demarcations between different schools of thought (Kaboolian, 1998, Levi-Faur, 2004, Agranoff & McGuire, 2004).

However, managing ‘beyond’ such boundaries is a routinely recurring aspiration that transcends sectors and local concerns. Unsurprisingly then, there is an increasing understanding of the need to acknowledge and manage such boundaries (whether they be physical, social or organisational) within public management as a discipline (Currie et al 2007, Fitzsimmons and White, 1997, Murtagh, 2002). This paper explores the impact of boundaries on public management strategic decision-making in the sectors of urban regeneration and healthcare. In particular, it focuses on demarcations to physical space, communal identity and within professional relationships in these sectors.

The first section describes the research that gave rise to the paper and the cases examined. Next we briefly define what we mean by boundaries. We explore issues that have emerged from our analysis of urban regeneration and health care singularly, before looking at how the concept of boundaries is a recurrent concern across the sectors. The main contribution of the paper is an exploration of how a CAS lens can bring a new insight into the concept of boundaries and decision-making in the two sets of case studies. This discussion will concentrate on initial conditions, bifurcation and adaptation as key CAS factors in relation to boundaries. We conclude with a brief discussion on the benefits of a CAS lens to an analysis of boundaries in public management decision-making.
References:

Agranoff, R. and McGuire, M. (2003) Collaborative Public Management: Strategies for Local Government. Washington, DC: Georgetown Univ. Press.

Currie, G., Lockett, A. (2007) “A critique of transformational leadership: moral, professional & contingent dimensions of leadership within public services organizations”. Human Relations 60: 341-370.

Fitzsimmons and White, (1997) "Crossing boundaries: communication between professional groups", Journal of Management in Medicine, Vol. 11 Iss: 2, pp.96 – 101

Kaboolian, L. (1998) “The New Public Management: Challenging the Boundaries of the Management vs. Administration Debate” Public Administration Review Vol. 58, No. 3 pp.189-193

Levi-Faur D. and Vigoda-Gadot Eran (eds) (2004) International Public Policy and Management: Policy Learning Beyond Regional, Cultural and Political Boundaries, Marcel Dekker,
Midgley, G. (ed) (2003) Systems Thinking. London: Sage Publications

Midgley, G. (2000) Systemic Intervention: Philosophy, Methodology and Practice. New York, NY: Kluwer.

Murtagh, B. (2002). The Politics of Territory: Policy and Segregation in Northern Ireland. Basingstoke, Palgrave.

Rhodes, ML, Joanne Murphy, Jenny Muir, John Murray (2011) Public Management & Complexity Theory: Richer Decision Making in Irish Public Services, UK: Routledge

US Credit Unions: Survival, Consolidation and Growth

This study uses hazard function estimations and time-series and cross-sectional growth regressions to examine the impact of exit through merger and acquisition (M&A) or failure, and internally-generated growth, on the firm-size distribution within the US credit union sector. Consolidation through M&A was the principal cause of a reduction in the number of credit unions, but impact on concentration was small. Divergence between the average internally-generated growth of smaller and larger credit unions was the principal driver of the rise in concentration.

Regulation of the pollen-specific actin-depolymerizing factor LIADF1

Pollen tube growth is dependent on a dynamic actin cytoskeleton, suggesting that actin-regulating proteins are involved. We have examined the regulation of the lily pollen-specific actin-depolymerizing factor (ADF) LIADF1. Its actin binding and depolymerizing activity is pH sensitive, inhibited by certain phosphoinositides, but not controlled by phosphorylation. Compared with its F-actin binding properties, its low activity in depolymerization assays has been used to explain why pollen ADF decorates F-actin in pollen grains. This low activity is incompatible with a role in increasing actin dynamics necessary to promote pollen tube growth. We have identified a plant homolog of actin-interacting protein, AIP1, which enhances the depolymerization of F-actin in the presence of LIADF1 by similar to60%. Both pollen ADF and pollen AIP1 bind F-actin in pollen grains but are mainly cytoplasmic in pollen tubes. Our results suggest that together these proteins remodel actin filaments as pollen grains enter and exit dormancy.

Performance analysis of an infinite array linear clustered plug nozzle

The effects of module shape, module design, three dimensional flow field generated by modules, and partition of primary nozzle on the performance of an infinite array linear clustered plug nozzle are discussed. The module shape is a critical element for nozzle performance and the partition of the primary nozzle with round-to square modules causes a vacuum thrust reduction with respect to two-dimensional model. The performance analysis of different module configuration allows weighing separately the role of clustering and the role of module design. In operating conditions characterized by turned off modules the performance loss is larger, but the difference due to the module shape are smaller and mostly due to the module contribution. The performance of the plug nozzle can be improved by module design, which reduces the module exit flow nonuniformity.

3D Analysis of Seepage under Hydraulic Structures with Intermediate Filters

Seepage flow under hydraulic structures provided with intermediate filters has been investigated. The flow through the banks of the canal has been included in the model. Different combinations of intermediate filter and canal width were studied. Different lengths of the floor, differential heads, and depths of the sheet pile driven beneath the floor were also investigated. The introduction of an intermediate filter to the floor of hydraulic structures reduced the uplift force acting on the downstream floor by up to 72%. The maximum uplift reduction occurred when the ratio of the distance of filter location downstream from the cutoff to the differential head was 1. Introducing a second filter in the downstream side resulted in a further reduction in the exit hydraulic gradient and in the uplift force, which reached 90%. The optimum locations of the two filters occurred when the first filter was placed just downstream of the cutoff wall and the second filter was placed nearly at the middistance between the cutoff and the end toe of the floor. The results showed significant differences between the three-dimensional (3D) and the two-dimensional (2D) analyses.

Ordering the cytochrome c-initiated caspase cascade:hierarchical activation of caspases-2, -3, -6, -7, -8, and -10 in a caspase-9-dependent manner

Exit of cytochrome c from mitochondria into the cytosol has been implicated as an important step in apoptosis. In the cytosol, cytochrome c binds to the CED-4 homologue, Apaf-1, thereby triggering Apaf-1-mediated activation of caspase-9. Caspase-9 is thought to propagate the death signal by triggering other caspase activation events, the details of which remain obscure. Here, we report that six additional caspases (caspases-2, -3, -6, -7, -8, and -10) are processed in cell-free extracts in response to cytochrome c, and that three others (caspases-1, -4, and -5) failed to be activated under the same conditions. In vitro association assays confirmed that caspase-9 selectively bound to Apaf-1, whereas caspases-1, -2, -3, -6, -7, -8, and -10 did not. Depletion of caspase-9 from cell extracts abrogated cytochrome c-inducible activation of caspases-2, -3, -6, -7, -8, and -10, suggesting that caspase-9 is required for all of these downstream caspase activation events. Immunodepletion of caspases-3, -6, and -7 from cell extracts enabled us to order the sequence of caspase activation events downstream of caspase-9 and reveal the presence of a branched caspase cascade. Caspase-3 is required for the activation of four other caspases (-2, -6, -8, and -10) in this pathway and also participates in a feedback amplification loop involving caspase-9.

Lovastatin production by Aspergillus terreus using lignocellulose biomass in large scale packed bed reactor

The effect of superficial air velocity on lovastatin production by Aspergillus terreus PL10 using wheat bran and wheat straw was investigated in a 7 l and a 1200 l packed bed reactor. Mass transfer and reaction limitations on bioconversion in the 1200 l reactor was studied based on a central composite design of experiments constructed using the superficial air velocity and solid substrate composition as variables and lovastatin production as response.
The surface response prediction showed a maximum lovastatin production of 1.86 mg g-1 dry substrate on day 5 of the bioconversion process when the reactor was operated using 0.19 vvm airflow rate (23.37 cm min-1 superficial air velocity) and 54% substrate composition (wC). Lovastatin production did not increase significantly with superficial air velocity in the 7 l reactor. Variation in temperature and exit CO2 composition was recorded, and the Damköhler number was calculated for lovastatin production at these two scales. The results showed that in larger reactors mass transfer limitation controlled bioconversion while in smaller reactors bioconversion was controlled by reaction rate limitations. In addition, mass transfer limitations in larger reactors reduced the rate of metabolic heat removal, resulting in hot spots within the substrate bed.

Multibody modelling of a TB31 and a TB32 crash test with vertical portable concrete barriers: model verification and sensitivity analysis.

In this article the multibody simulation software package MADYMO for analysing and optimizing occupant safety design was used to model crash tests for Normal Containment barriers in accordance with EN 1317. The verification process was carried out by simulating a TB31 and a TB32 crash test performed on vertical portable concrete barriers and by comparing the numerical results to those obtained experimentally. The same modelling approach was applied to both tests to evaluate the predictive capacity of the modelling at two different impact speeds. A sensitivity analysis of the vehicle stiffness was also carried out. The capacity to predict all of the principal EN1317 criteria was assessed for the first time: the acceleration severity index, the theoretical head impact velocity, the barrier working width and the vehicle exit box. Results showed a maximum error of 6% for the acceleration severity index and 21% for theoretical head impact velocity for the numerical simulation in comparison to the recorded data. The exit box position was predicted with a maximum error of 4°. For the working width, a large percentage difference was observed for test TB31 due to the small absolute value of the barrier deflection but the results were well within the limit value from the standard for both tests. The sensitivity analysis showed the robustness of the modelling with respect to contact stiffness increase of ±20% and ±40%. This is the first multibody model of portable concrete barriers that can reproduce not only the acceleration severity index but all the test criteria of EN 1317 and is therefore a valuable tool for new product development and for injury biomechanics research.

The effect of nozzle geometry on the flow characteristics of small water jets

A wide variety of processes make use of plain orifice nozzles. Fuel injectors for internal combustion engines incorporate these nozzles to generate finely atomized sprays. Processes such as jet cutting, jet cleaning, and hydroentanglement, on the other hand, use similar nozzles, but require coherent jets. The spray or jet characteristics depend on the stability of the flow emerging from the orifice. This problem has been extensively researched for nozzles with diameters above 300 μm. Much less is known about the characteristics of jets produced by nozzles with smaller diameters, where viscous effects and small geometric variations due to manufacturing tolerances are likely to play an increasing role. Results are presented of a wide-ranging investigation of geometry effects on the flow parameters and jet characteristics of nozzles with diameters between 120 and 170 μm. Nozzles with circular cross-section and conical, cone-capillary and capillary axial designs were investigated. For conical and cone-capillary nozzles, the effect of cone angle and effects due to interactions between adjacent nozzles in the multi-hole cone-capillary nozzles were studied. For capillary nozzles, the effects of diameter variations and inlet edge roundness for capillary nozzles were considered. Furthermore, the effect of varying the aspect ratio (ratio of major and minor axes) of elliptical nozzles was studied. Flowrate and jet impact force measurements were carried out to determine the discharge coefficient C, velocity coefficient C, and contraction coefficient C of the nozzles for supply pressures between 3 and 12 MPa. Visualizations of the jet flow were carried out in the vicinity of the nozzle exit in order to identify near-nozzle flow regimes and to study jet coherence. The relationship between nozzle geometry, discharge characteristics, and jet coherence is examined. © IMechE 2006.

Identifying solutions to increase participation in physical activity interventions within a socio-economically disadvantaged community: a qualitative study

Background: There is an urgent need to increase population levels of physical activity, particularly amongst those who are socio-economically disadvantaged. Multiple factors influence physical activity behaviour but the generalisability of current evidence to such ‘hard-to-reach’ population subgroups is limited by difficulties in recruiting them into studies. Also, rigorous qualitative studies of lay perceptions and perceptions of community leaders about public health efforts to increase physical activity are sparse. We sought to explore, within a socio-economically disadvantaged community, residents’ and community leaders’ perceptions of physical activity (PA) interventions and issues regarding their implementation, in order to improve understanding of needs, expectations, and social/environmental factors relevant to future interventions.

Methods: Within an ongoing regeneration project (Connswater Community Greenway), in a socio-economically disadvantaged community in Belfast, we collaborated with a Community Development Agency to purposively sample leaders from public- and voluntary-sector community groups and residents. Individual semi-structured interviews were conducted with 12 leaders. Residents (n=113), of both genders and a range of ages (14 to 86 years) participated in focus groups (n=14) in local facilities. Interviews and focus groups were recorded, transcribed verbatim and analysed using a thematic framework.

Results: Three main themes were identified: awareness of PA interventions; factors contributing to intervention effectiveness; and barriers to participation in PA interventions. Participants reported awareness only of interventions in which they were involved directly, highlighting a need for better communications, both inter- and intra-sectoral, and with residents. Meaningful engagement of residents in planning/organisation, tailoring to local context, supporting volunteers, providing relevant resources and an ‘exit strategy’ were perceived as important factors related to intervention effectiveness. Negative attitudes such as apathy, disappointing experiences, information with no perceived personal relevance and limited access to facilities were barriers to people participating in interventions.

Conclusions: These findings illustrate the complexity of influences on a community’s participation in PA interventions and support a social-ecological approach to promoting PA. They highlight the need for cross-sector working, effective information exchange, involving residents in bottom-up planning and providing adequate financial and social support. An in-depth understanding of a target population’s perspectives is of key importance in translating PA behaviour change theories into practice.

Enhancing the Efficiency of Slit-Coupling to Surface-Plasmon Polariton via Dispersion Engineering

We describe a simple method for enhancing the efficiency of coupling from a free-space transverse-magnetic (TM) plane-wave mode into a surface-plasmon-polariton (SPP) mode. The coupling structure consists a metal film with a dielectric-filled slit and a planar, dielectric layer on the slit-exit side of the metal film. By varying the dielectric layer thickness, the wavevector of the SPP mode on the metal surface can be tuned to match the wavevector magnitude of the modes emanating from the slit exit, enabling high-efficiency radiation coupling into the SPP mode at the slit exit. An optimal dielectric layer thickness of approximately 100 nm yields a visible-frequency SPP coupling efficiency approximately 4 times greater than the SPP coupling efficiency without the dielectric layer. Commensurate coupling enhancement is observed spanning the free-space wavelength range 400 nm < or = lambda(0) < or = 700 nm. We map the dependence of the SPP coupling efficiency on the slit width, the dielectric-layer thickness, and the incident wavelength to fully characterize this SPP coupling methodology