Anisotropy of single crystal 3C-SiC during nanometric cutting

3C–SiC (the only polytype of SiC that resides in a diamond cubic lattice structure) is a relatively new material that exhibits most of the desirable engineering properties required for advanced electronic applications. The anisotropy exhibited by 3C–SiC during its nanometric cutting is significant, and the potential for its exploitation has yet to be fully investigated. This paper aims to understand the influence of crystal anisotropy of 3C–SiC on its cutting behaviour. A molecular dynamics simulation model was developed to simulate the nanometric cutting of single-crystal 3C–SiC in nine (9) distinct combinations of crystal orientations and cutting directions, i.e. (1?1?1) <-1?1?0>, (1?1?1) <-2?1?1>, (1?1?0) <-1?1?0>, (1?1?0) <0?0?1>, (1?1?0) <1?1?-2>, (0?0?1) <-1?1?0>, (0?0?1) <1?0?0>, (1?1?-2) <1?-1?0> and (1?-2?0) <2?1?0>.

In order to ensure the reliability of the simulation results, two separate simulation trials were carried out with different machining parameters. In the first trial, a cutting tool rake angle of -25°, d/r (uncut chip thickness/cutting edge radius) ratio of 0.57 and cutting velocity of 10 m s-1 were used whereas a second trial was done using a cutting tool rake angle of -30°, d/r ratio of 1 and cutting velocity of 4 m s-1. Both the trials showed similar anisotropic variation.

The simulated orthogonal components of thrust force in 3C–SiC showed a variation of up to 45%, while the resultant cutting forces showed a variation of 37%. This suggests that 3C–SiC is highly anisotropic in its ease of deformation. These results corroborate with the experimentally observed anisotropic variation of 43.6% in Young's modulus of 3C–SiC. The recently developed dislocation extraction algorithm (DXA) [1, 2] was employed to detect the nucleation of dislocations in the MD simulations of varying cutting orientations and cutting directions. Based on the overall analysis, it was found that 3C–SiC offers ease of deformation on either (1?1?1) <-1?1?0>, (1?1?0) <0?0?1>, or (1?0?0) <1?0?0> setups.

Multiscale simulation of nanometric cutting of single crystal copper and its experimental validation

In this paper a multiscale simulation study was carried out in order to gain in-depth understanding of machining mechanism of nanometric cutting of single crystal copper. This study was focused on the effects of crystal orientation and cutting direction on the attainable machined surface quality. The machining mechanics was analyzed through cutting forces, chip formation morphology, generation and evolution of defects and residual stresses on the machined surface. The simulation results showed that the crystal orientation of the copper material and the cutting direction significantly influenced the deformation mechanism of the workpiece materials during the machining process. Relatively lower cutting forces were experienced while selecting crystal orientation family {1 1 1}. Dislocation movements were found to concentrate in front of the cutting chip while cutting on the (1 1 1) surface along the View the MathML source cutting direction thus, resulting in much smaller damaged layer on the machined surface, compared to other orientations. This crystal orientation and cutting direction therefore recommended for nanometric cutting of single crystal copper in practical applications. A nano-scratching experiment was performed to validate the above findings.

The cemented custom femoral stem--a 10 year review

We report a series of 706 patients (759 hip implants) with an average follow up of 10.5 years (range, 10-11 years) following total hip replacement (THR) using a cemented custom-made femoral stem and a cemented HDP acetabular component. The fate of every implant is known. One hundred and seventy-four patients (23%) were deceased at the time of their 10-year review all died with a functioning THR in situ. Four hundred and sixty-two patients (61%) were subsequently reviewed. One hundred and twenty three patients (16%) were assessed by telephone review, as they were too ill or unwilling to attend. Kaplan-Meier survival analysis (all components) demonstrated a median survival at 10 years of 96.05% or 95% Confidence Intervals (CI) for median survival of (94.41% to 97.22%). Revision surgery occurred in 30 cases (3.9%). Seventeen had full revisions (2.2%) and 13 (1.7%) socket revisions only. Twenty-one out of 30 revisions were for infection or dislocation. There were 2 cases (0.3%) of revision for aseptic loosening of the stem. The 10-year results of the custom femoral titanium stem are encouraging and compare well with other cemented systems.

Dynamic Buffer Management for Multimedia Services in 3.5G Wireless Networks

This paper presents and investigates a dynamic
buffer management scheme for QoS control of multimedia
services in a 3.5G wireless system i.e. the High Speed Downlink
Packet Access (HSDPA). HSDPA was introduced to enhance
UMTS for high-speed packet switched services. With HSDPA,
packet scheduling and HARQ mechanisms in the base station
require data buffering at the air interface thus introducing a
potential bottleneck to end-to-end communication. Hence, for
multimedia services with multiplexed parallel diverse flows
such as video and data in the same end-user session, buffer
management schemes in the base station are essential to support
end-to-end QoS provision. We propose a dynamic buffer management
scheme for HSDPA multimedia sessions with aggregated real-time and non real-time flows in the paper. The end-to-end performance impact of the scheme is evaluated with an example multimedia session comprising a real-time streaming
flow concurrent with TCP-based non real-time flow via extensive HSDPA simulations. Results demonstrate that the scheme can guarantee the end-to-end QoS of the real-time streaming flow, whilst simultaneously protecting non real-time flow from starvation resulting in improved end-to-end throughput performance

Nanoindentation of polysilicon and single crystal silicon: Molecular dynamics simulation and experimental validation

This paper presents novel advances on the deformation behaviour of polycrystalline and single crystal silicon using molecular dynamics (MD) simulation and validation of the same via nanoindentation experiments. In order to unravel the mechanism of deformation, four simulations were performed: Indentation of polycrystalline silicon substrate with a (i) Berkovich pyramidal and a (ii) spherical (arc) indenter, and indentation of a single crystal silicon substrate with these two indenters. The simulation results reveal that high pressure phase transformation (HPPT) in silicon (Si-I to Si-II phase transformation) occurred in all cases, however, its extent and the manner in which it occurred differed significantly between polycrystalline silicon and single crystal silicon, and was the main driver of differences in nanoindentation deformation behaviour between the two types of silicon. An interesting observation was that in polycrystalline silicon, the HPPT was observed to occur preferentially along the grain boundaries than across the grain boundaries. An automated dislocation extraction algorithm (DXA) revealed no dislocations in the deformation zone, suggesting HPPT to be the primary mechanism in inducing plasticity in silicon.

Topical Review: The current understanding on the diamond machining of silicon carbide

The Glenn Research Centre of NASA, USA (www.grc.nasa.gov/WWW/SiC/, silicon carbide electronics) is in pursuit of realizing bulk manufacturing of silicon carbide (SiC), specifically by mechanical means. Single point diamond turning (SPDT) technology which employs diamond (the hardest naturally-occurring material realized to date) as a cutting tool to cut a workpiece is a highly productive manufacturing process. However, machining SiC using SPDT is a complex process and, while several experimental and analytical studies presented to date aid in the understanding of several critical processes of machining SiC, the current knowledge on the ductile behaviour of SiC is still sparse. This is due to a number of simultaneously occurring physical phenomena that may take place on multiple length and time scales. For example, nucleation of dislocation can take place at small inclusions that are of a few atoms in size and once nucleated, the interaction of these nucleations can manifest stresses on the micrometre length scales. The understanding of how stresses manifest during fracture in the brittle range, or dislocations/phase transformations in the ductile range, is crucial in understanding the brittle–ductile transition in SiC. Furthermore, there is a need to incorporate an appropriate simulation-based approach in the manufacturing research on SiC, owing primarily to the number of uncertainties in the experimental research that includes wear of the cutting tool, poor controllability of the nano-regime machining scale (effective thickness of cut), and coolant effects (interfacial phenomena between the tool, workpiece/chip and coolant), etc. In this review, these two problems are combined together to posit an improved understanding on the current theoretical knowledge on the SPDT of SiC obtained from molecular dynamics simulation.

Microstructure evolution of 6061 O Al alloy during ultrasonic consolidation:An insight from electron backscatter diffraction

6061 O Al alloy foils were welded to form monolithic and SiC fibre-embedded samples using the ultrasonic consolidation (UC) process. Contact pressures of 135, 155 and 175 MPa were investigated at 20 kHz frequency, 50% of the oscillation amplitude, 34.5 mm s sonotrode velocity and 20 °C. Deformed microstructures were analysed using electron backscatter diffraction (EBSD). At all contact pressures deformation occurs by non-steady state dislocation glide. Dynamic recovery is active in the upper and lower foils. Friction at the welding interface, instantaneous internal temperatures (0.5-0.8 of the melting temperature, T), contact pressure and fast strain rates result in transient microstructures and grain size reduction by continuous dynamic recrystallization (CDRX) within the bonding zone. Bonding occurs by local grain boundary migration, which allows diffusion and atom interlocking across the contact between two clean surfaces. Textures weaken with increasing contact pressure due to increased strain hardening and different grain rotation rates. High contact pressures enhance dynamic recovery and CDRX. Deformation around the fibre is intense within 50 μm and extends to 450 μm from it. © 2009 Acta Materialia Inc.

Twinning anisotropy of tantalum during nanoindentation

Unlike other BCC metals, the plastic deformation of nanocrystalline Tantalum during compression is regulated by deformation twinning. Whether or not this twinning exhibits anisotropy was investigated through simulation of displacement-controlled nanoindentation test using molecular dynamics simulation. MD data was found to correlate well with the experimental data in terms of surface topography and hardness measurements. The mechanism of the transport of material was identified due to the formation and motion of prismatic dislocations loops (edge dislocations) belonging to the 1/2<111> type and <100> type Burgers vector family. Further analysis of crystal defects using a fully automated dislocation extraction algorithm (DXA) illuminated formation and migration of twin boundaries on the (110) and (111) orientation but not on the (010) orientation and most importantly after retraction all the dislocations disappeared on the (110) orientation suggesting twinning to dominate dislocation nucleation in driving plasticity in tantalum. A significant finding was that the maximum shear stress (critical Tresca stress) in the deformation zone exceeded the theoretical shear strength of tantalum (Shear modulus/ 2π~10.03 GPa) on the (010) orientation but was lower than it on the (110) and the (111) orientations. In light to this, the conventional lore of assuming the maximum shear stress being 0.465 times the mean contact pressure was found to break down at atomic scale.

qPCR utilization for the study of RNA Polymerase I transcription

Ribosome biogenesis is a fundamental cellular process tightly linked to cell growth and proliferation, which requires the coordinated transcription of all three nuclear polymerases. Synthesis of ribosomal RNA (rRNA) by RNA polymerase I (Pol I) has been suggested as a key regulator of ribosome biogenesis, and there is a strong link between transcription of ribosomal RNAs and cellular proliferation. This makes Pol I transcription a valid and attractive target for anticancer therapy. At the moment however there are only a small number of compounds that act as specific inhibitors of Pol I transcription and this makes it very difficult for the development of drugs which would target rRNA transcription and consequently ribosome biogenesis. Therefore, to aid in the development of new inhibitors of Pol I, high-throughput methods to monitor and detect changes in Pol I activity need to be developed. This current study aimed to address the question of whether or not quantitative PCR (qPCR) could be used to detect changes in rRNA production in cells under different conditions that repress Pol I activity i.e. serum starvation and drug treatment. Our results have shown that using primers and a hydrolysis probe designed for the 5’ETS region of the pre-rRNA molecule, rRNA levels in both treated and untreated cells could be determined by using qPCR.
Amplification resulted in formation of a single product and S1 nuclease protection assay confirmed the down-regulation of Pol I transcription. Following serum-starvation and drug treatment there was a dramatic reduction in the amount of 5’ETS transcript quantitated by both Sybr Green chemistry and the use of a fluorescently labelled hydrolysis probe. The optimization of the qPCR strategy will be discussed.

Predation in the marine intertidal amphipod Echinogammarus marinus Leach: implications of inter- and intra-individual variation

Studies of competition, predator–prey dynamics and food webs typically consider conspecifics as equal, however, individuals from the same population that are seemingly identical can show considerable variation with regards to a number of processes. Such phenomena may be demonstrated in terms of diet, and the quantities and types of resources that are consumed are commonly considered. The marine amphipod Echinogammarus marinus, a recently demonstrated predator on intertidal rocky shores, has been shown to consume a wide range of food types but it is unknown how this may vary between individuals. Here, we investigated the variation that occurs both among and within individuals of a population of E. marinus with respect to the mean numbers consumed of a common prey item, the isopod Jaera nordmanni. First, by comparing the length of starvation times, used as a proxy for hunger level, individuals maintained without food for up to 24 h consumed significantly less prey during feeding trials than those starved for 48 h and longer. The degree of inter-individual variation within each starvation period was also found to differ, with greater variation among individuals starved for shorter periods of time than those starved for longer time periods. Secondly, we tested whether individual amphipods tracked over time consumed consistently similar numbers of prey or whether they showed intra-individual variation, and if so, to what degree. We found that the numbers of prey consumed per individual could be predicted in the short-term between consecutive feeding trials, however over the long-term this relationship broke down. These results are discussed with respect to potential physiological and behavioural mechanisms, as well as the implications that such variation may have for stability of prey populations in the field.

Effects of particle/matrix interface and strengthening mechanisms on the mechanical properties of metal matrix composites

A randomly distributed multi-particle model considering the effects of particle/matrix interface and strengthening mechanisms introduced by the particles has been constructed. Particle shape, distribution, volume fraction and the particles/matrix interface due to the factors including element diffusion were considered in the model. The effects of strengthening mechanisms, caused by the introduction of particles on the mechanical properties of the composites, including grain refinement strengthening, dislocation strengthening and Orowan strengthening, are incorporated. In the model, the particles are assumed to have spheroidal shape, with uniform distribution of the centre, long axis length and inclination angle. The axis ratio follows a right half-normal distribution. Using Monte Carlo method, the location and shape parameters of the spheroids are randomly selected. The particle volume fraction is calculated using the area ratio of the spheroids. Then, the effects of particle/matrix interface and strengthening mechanism on the distribution of Mises stress and equivalent strain and the flow behaviour for the composites are discussed.

Pre-operative fasting for intravenous conscious sedation used in dental treatment: are conclusions based on relative risk management or evidence?

Intravenous sedation is a widely used pharmacological method of patient management commonly used in dental surgery for the treatment of anxious patients. Variety exists in fasting regimes between different centres offering dental sedation, with some advocating starvation in line with general anaesthesia protocols and others not enforcing starvation at all. The currently available guidelines on fasting protocols are ambiguous and open to interpretation partly because they are based on expert opinion rather than evidence-based research. This article reviews the available evidence on the subject of pre-operative fasting and discusses current guidelines.

Low cycle fatigue properties of CLAM steel at room temperature

The low cycle fatigue (LCF) properties and the fracture behavior of China Low Activation Martensitic (CLAM) steel have been studied over a range of total strain amplitudes from 0.2 to 2.0%. The specimens were cycled using tension-compression loading under total strain amplitude control. The CLAM steel displayed initial hardening followed by continuous softening to failure at room temperature in air. The relationship between strain and fatigue life was predicted using the parameters obtained from fatigue test. The factors effecting on low cycle fatigue of CLAM steel consisted of initial state of matrix dislocation arrangement, magnitude of cyclic stress, magnitude of total strain amplitude and microstructure. The potential mechanisms controlling the stress response, cyclic strain resistance and low cycle fatigue life have been evaluated.

Assessment of lux-marked Pseudomonas fluorescens for reporting on organic carbon compounds

Carbon-flow from plant roots to the rhizosphere provides a major source of nutrients for the soil microbial population. However, quantification of carbon-flow is problematic due to its complex composition. This study investigated the potential of lux-marked Pseudomonas fluorescens to discriminate between forms of carbon present in the rhizosphere by measuring the light response to a range of carbon compounds. Results indicate that bioluminescence of short-term carbon-starved P. fluorescens is dependent upon the source and concentration of carbon. This system, therefore, has the potential to both quantify and qualify organic acids present in rhizodeposits.

Biotransformation of 2,4,6-trinitrotoluene (TNT) by ectomycorrhizal basidiomycetes

The ability of four ectomycorrhizal basidiomycetes to biotransform 2,4,6-trinitrotoluene (TNT) in axenic culture was tested. All species were capable of TNT biotransformation to a greater or lesser extent. When biotransformation was expressed on a biomass basis 4 out of the 5 isolates tested were equally efficient at transforming TNT. The factors regulating TNT biotransformation were investigated in detail for one fungus, Suillus variegatus. When the fungus was grown under nitrogen limiting conditions the rate of biotransformation decreased relative to nitrogen sufficient conditions, but no decrease was observed under short term carbon starvation. Extracellular enzymes of S. variegatus could transform TNT, but transformation was greater in intact cells. The mycelial cell wall fraction did not degrade TNT. The TNT concentration that caused 50% reduction in biomass (EC₅₀) for S. variegatus was within the range observed for other basidiomycete fungi being between 2-10 μg mL^-1. The potential use of ectomycorrhizal basidiomycetes as in-situ bioremediation agents for TNT contaminated soils is discussed.