The use of recycled demolition aggregate in precast concrete products – Phase III: Concrete pavement flags

A study undertaken at the University of Liverpool has investigated the potential for using construction and demolition waste (C&DW) derived aggregate in the manufacture of a range of precast concrete products, i.e. building and paving blocks and pavement flags. Phase III, which is reported here, investigated
concrete pavement flags. This was subsequent to studies on building and paving blocks. Recycled demolition aggregate can be used to replace newly quarried limestone aggregate, usually used in coarse (6 mm) and fine (4 mm-to-dust) gradings. The first objective was, as was the case with concrete building
and paving blocks, to replicate the process used by industry in fabricating concrete pavement flags in the laboratory. The ‘‘wet’’ casting technique used by industry for making concrete flags requires a very workable mix so that the concrete flows into the mould before it is compressed. Compression squeezes out water from the top as well as the bottom of the mould. This industrial casting procedure was successfully replicated in the laboratory by using an appropriately modified cube crushing machine and a special mould typical of what is used by industry. The mould could be filled outside of the cube crushing machine and then rolled onto a steel frame and into the machine for it to be compressed. The texture and mechanical properties of the laboratory concrete flags were found to be similar to the factory ones. The experimental work involved two main series of tests, i.e. concrete flags made with concrete- and
masonry-derived aggregate. Investigation of flexural strength was required for concrete paving flags. This is different from building blocks and paving blocks which required compressive and tensile splitting strength respectively. Upper levels of replacement with recycled demolition aggregate were determined
that produced similar flexural strength to paving flags made with newly quarried aggregates, without requiring an increase in the cement content. With up to 60% of the coarse or 40% of the fine fractions replaced with concrete-derived aggregates, the target mean flexural strength of 5.0 N/mm2 was still
achieved at the age of 28 days. There was similar detrimental effect by incorporating the fine masonry-derived aggregate. A replacement level of 70% for coarse was found to be satisfactory and also conservative. However, the fine fraction replacement could only be up to 30% and even reduced to 15% when used for mixes where 60% of the coarse fraction was also masonry-derived aggregate.

Information aggregation and belief elicitation in experimental parimutuel betting markets

This paper studies the impact of belief elicitation on informational efficiency and individual behavior in experimental parimutuel betting markets. In one treatment, groups of eight participants, who possess a private signal about the eventual outcome, play a sequential betting game. The second treatment is identical, except that bettors are observed by eight other participants who submit incentivized beliefs about the winning probabilities of each outcome. In the third treatment, the same individuals make bets and assess the winning probabilities of the outcomes. Market probabilities more accurately reflect objective probabilities in the third than in the other two treatments. Submitting beliefs reduces the favorite-longshot bias and making bets improves the accuracy of elicited beliefs. A level-k framework provides some insights about why belief elicitation improves the capacity of betting markets to aggregate information. (C) 2012 Elsevier B.V. All rights reserved.

Second-to-Fourth Digit Ratio and Impulsivity: A Comparison between Offenders and Nonoffenders

Personality characteristics, particularly impulsive tendencies, have long been conceived as the primary culprit in delinquent behavior. One crucial question to emerge from this line of work is whether impulsivity has a biological basis. To test this possibility, 44 male offenders and 46 nonoffenders completed the Eysenck Impulsivity Questionnaire, and had their 2D:4D ratio measured. Offenders exhibited smaller right hand digit ratio measurements compared to non-offenders, but higher impulsivity scores. Both impulsivity and 2D:4D ratio measurements significantly predicted criminality (offenders vs. nonoffenders). Controlling for education level, the 2D:4D ratio measurements had remained a significant predictor of criminality, while impulsivity scores no longer predicted criminality significantly. Our data, thus, indicates that impulsivity but not 2D:4D ratio measurements relate to educational attainment. As offenders varied in their number of previous convictions and the nature of their individual crimes, we also tested for differences in 2D:4D ratio and impulsivity among offenders. Number of previous convictions did not correlate significantly with the 2D:4D ratio measurements or impulsivity scores. Our study established a link between a biological marker and impulsivity among offenders (and lack thereof among non-offenders), which emphasise the importance of studying the relationship between biological markers, impulsivity and criminal behavior.

The social construction of illness:Key insights and policy implications.

The social construction of illness is a major research perspective in medical sociology. This article traces the roots of this perspective and presents three overarching constructionist findings. First, some illnesses are particularly embedded with cultural meaning--which is not directly derived from the nature of the condition--that shapes how society responds to those afflicted and influences the experience of that illness. Second, all illnesses are socially constructed at the experiential level, based on how individuals come to understand and live with their illness. Third, medical knowledge about illness and disease is not necessarily given by nature but is constructed and developed by claims-makers and interested parties. We address central policy implications of each of these findings and discuss fruitful directions for policy-relevant research in a social constructionist tradition. Social constructionism provides an important counterpoint to medicine's largely deterministic approaches to disease and illness, and it can help us broaden policy deliberations and decisions.

Medicalization, markets and consumers.

This paper examines the impact of changes in the medical marketplace on medicalization in U.S. society. Using four cases (Viagra, Paxil, human growth hormone and in vitro fertilization), we focus on two aspects of the changing medical marketplace: the role of direct-to-consumer advertising of prescription drugs and the emergence of private medical markets. We demonstrate how consumers and pharmaceutical corporations contribute to medicalization, with physicians, insurance coverage, and changes in regulatory practices playing facilitating roles. In some cases, insurers attempt to counteract medicalization by restricting access. We distinguish mediated and private medical markets, each characterized by differing relationships with corporations, insurers, consumers, and physicians. In the changing medical environment, with medical markets as intervening factors, corporations and insurers are becoming more significant determinants in the medicalization process.

Incidence and natural history of proliferative sickle cell retinopathy:Observations from a cohort study

Objective: To describe the incidence, prevalence, and natural history of proliferative sickle cell retinopathy (PSR). Design: Prospective longitudinal study over 20 years. Participants: Newborn screening of 100000 consecutive deliveries from 1973 to 1981 identified 315 children with homozygous sickle cell (SS) disease and 201 with SS-hemoglobin C (SC) disease. By the age of 5 years, 307 SS patients and 166 SC patients were alive and living in Jamaica and were recruited for this ophthalmic study. Methods: Description of retinal vascular changes on annual angiography and angioscopy. Main Outcome Measures: Incidence and prevalence of PSR and its behavior on follow-up. Progression of PSR was investigated using the number of eyes affected (none, one, both) and the interval until PSR onset. Results: At last review in January 2000, PSR had developed in 59 patients (14 SS, 45 SC), unilaterally in 36 patients and bilaterally in 23. Incidence increased with age in both genotypes, with crude annual incidence rates of 0.5 cases (95% confidence interval [CI], 0.3-0.8) per 100 SS subjects and 2.5 cases (95% CI, 1.9-3.3) per 100 SC subjects. Prevalence was greater in SC disease, and by the ages of 24 to 26 years, PSR had occurred in 43% subjects with SC disease and in 14% subjects with SS disease. Patients with unilateral PSR had a 16% (11% SS, 17% SC) probability of regressing to no PSR and a 14% (16% SS, 13% SC) probability of progressing to bilateral PSR. Those with bilateral PSR had an 8% (8% SS, 8% SC) probability of regressing to unilateral PSR and a 1% (0 SS, 2% SC) probability of regressing to a PSR-free state. Irretrievable visual loss occurred in only 1 of 82 PSR-affected eyes, and 1 required detachment surgery and recovered normal visual acuity. Conclusions: Longitudinal observations over 20 years in a cohort of patients followed from birth confirms a greater incidence and severity of PSR in SC disease, and shows that spontaneous regression occurred in 32% of PSR-affected eyes. Permanent visual loss was uncommon in subjects observed up to the age of 26 years. © 2005 by the American Academy of Ophthalmology.

Adsorption and aggregation properties of norovirus GI and GII virus-like particles demonstrate differing responses to solution chemistry

The transport properties (adsorption and aggregation behavior) of virus-like particles (VLPs) of two strains of norovirus ("Norwalk" GI.1 and "Houston" GII.4) were studied in a variety of solution chemistries. GI.1 and GII.4 VLPs were found to be stable against aggregation at pH 4.0-8.0. At pH 9.0, GI.1 VLPs rapidly disintegrated. The attachment efficiencies (a) of GI.1 and GII.4 VLPs to silica increased with increasing ionic strength in NaCl solutions at pH 8.0. The attachment efficiency of GI.1 VLPs decreased as pH was increased above the isoelectric point (pH 5.0), whereas at and below the isoelectric point, the attachment efficiency was erratic. Ca(2+) and Mg(2+) dramatically increased the attachment efficiencies of GI.1 and GII.4 VLPs, which may be due to specific interactions with the VLP capsids. Bicarbonate decreased attachment efficiencies for both GI.1 and GII.4 VLPs, whereas phosphate decreased the attachment efficiency of GI.1, while increasing GII.4 attachment efficiency. The observed differences in GI.1 and GII.4 VLP attachment efficiencies in response to solution chemistry may be attributed to differential responses of the unique arrangement of exposed amino acid residues on the capsid surface of each VLP strain.

Electronic, structural, and reactive properties of ultrathin aluminum oxide films on Pt(111)

Low-energy electron diffraction, X-ray photoelectron spectroscopy, high-resolution electron energy-loss spectroscopy, scanning tunneling microscopy, and temperature-programmed reaction spectrometry results are reported for the structural and reactive behavior of alumina films grown on Pt(111) as a function of thickness and oxidation temperature. Submonolayer Al films undergo compete oxidation at 300 K, annealing at 1100 K resulting in formation of somewhat distorted crystalline gamma-alumina, Thicker deposits require 800 K oxidation to produce Al2O3, and these too undergo crystallization at 800 K, yielding islands of apparently undistorted gamma-alumina on the Pt(111) surface. Oxidation of a p(2 x 2) Pt3Al surface alloy occurs only at>800 K, resulting in Al extraction, These alumina films on Pt(lll) markedly increase the coverage of adsorbed SO4 resulting from SO2 chemisorption onto oxygen-precovered surfaces. This results in enhanced propane uptake and subsequent reactivity relative to SO4/Pt(111). A bifunctional mechanism is proposed to account for our observations, and the relevance of these to an understanding of the corresponding dispersed systems is discussed.

Comportamento flessionale di nodi esterni in calcestruzzo fibrorinforzato

SOMMARIO – Si presenta un macro modello di tipo reticolare in grado di riprodurre il comportamento in presenza di taglio e momento di nodi esterni trave-colonna di telai in calcestruzzo fibrorinforzato con fibre di acciaio
uncinato ed ordinario. Il caricamento del sistema è di tipo monotono come nel caso dell’analisi di pushover. Il modello considera la presenza di armature orizzontali e verticali della regione nodale e tiene in conto delle modalità
di rottura legate allo snervamento delle barre e allo schiacciamento delle regioni compresse in regime di sforzi pluriassiali. Il modello include le deformazioni flessionali della trave e della colonna in presenza di sforzo normale costante e restituisce la risposta del sistema colonna-nodo-trave (sub-assembralggio) tramite le curve carico-freccia all’estremità della semitrave. Per i singoli costituenti (trave, colonna e nodo) si è considerata la prima fessurazione, lo snervamento e lo schiacciamento delle regioni compresse e si sono fornite precise indicazioni sulla sequenza degli eventi che come è noto sono di fondamentale importanza per lo sviluppo di un progetto plastico che rispetti la gerarchia delle resistenze. Con l’uso del modello il controllo della gerarchia delle resistenze avviene a livello sezionale (lo snervamento delle barre deve avvenire prima dello schiacciamento delle regioni compresse) o di macro elemento (nella regione nodale lo snervamento delle staffe precede la crisi dei puntoni) e dell’intero elemento
sub-assemblaggio trave debole, colonna forte e nodo sovraresistente.
La risposta ottenuta con i modello proposto è in buon accordo con le risposte sperimentali disponibili in letteratura (almeno in termini di resistenza del sub-assemblaggio). Il modello è stato ulteriormente validato con analisi
numeriche agli elementi finiti condotte con il codice ATENA-2D. Le analisi numeriche sono state condotte utilizzando per il calcestruzzo fibroso adeguate leggi costitutive proposte dagli autori ed in grado di cogliere gli effetti
di softening e di resistenza residua a trazione legati alla presenza di fibre. Ulteriori sviluppi del modello saranno indirizzati a includere gli effetti di sfilamento delle barre d’armatura della trave e del conseguente degrado delle
tensioni d’aderenza per effetto di carichi monotonici e ciclici.

SUMMARY – A softened strut-and-tie macro model able to reproduce the flexural behavior of external beam-tocolumn joints with the presence of horizontal and vertical steel bars, including softening of compressed struts and yielding of main and secondary steel bars, is presented, to be used for the pushover analysis. The model proposed is able to calculate also the flexural response of fibrous reinforced concrete (FRC) beam-to-column sub-assemblages in term of a multilinear load-deflection curves. The model is able to take into account of the tensile behavior of main bars embedded in the surrounding concrete and of the softening of the compressed strut, the arrangement and percentage of the steel bars, the percentage and the geometry of steel fibers. First cracking, yielding of main steel and crushing of concrete were identified to determine the corresponding loads and displacement and to plot the simplified monotonic load-deflection curves of the sub-assemblages subjected in the column to constant vertical
load and at the tip of the beam to monotonically increasing lateral force. Through these load-delfection curves the component (beam, joint and column) that first collapse can be recognized and the capacity design can be verified.
The experimental results available in the literature are compared with the results obtained through the proposed model. Further, a validation of the proposed model is numerically made by using a non linear finite element program (ATENA-2D) able to analyze the flexural behavior of sub-assemblages.

Optimized process for the inclusion of carbon nanotubes in elastomers with improved thermal and mechanical properties

The effects of addition of reinforcing carbon nanotubes (CNTs) into hydrogenated nitrile-butadiene rubber (HNBR) matrix on the mechanical, dynamic viscoelastic, and permeability properties were studied in this investigation. Different techniques of incorporating nanotubes in HNBR were investigated in this research. The techniques considered were more suitable for industrial preparation of rubber composites. The nanotubes were modified with different surfactants and dispersion agents to improve the compatibility and adhesion of nanotubes on the HNBR matrix. The effects of the surface modification of the nanotubes on various properties were examined in detail. The amount of CNTs was varied from 2.5 to 10 phr in different formulations prepared to identify the optimum CNT levels. A detailed analysis was made to investigate the morphological structure and mechanical behavior at room temperature. The viscoelastic behavior of the nanotube filler elastomer was studied by dynamic mechanical thermal analysis (DMTA). Morphological analysis indicated a very good dispersion of the CNTs for a low nanotube loading of 3.5 phr. A significant improvement in the mechanical properties was observed with the addition of nanotubes. DMTA studies revealed an increase in the storage modulus and a reduction in the glass-transition temperature after the incorporation of the nanotubes. Further, the HNBR/CNT nanocomposites were subjected to permeability studies. The studies showed a significant reduction in the permeability of nitrogen gas. Copyright © 2011 Wiley Periodicals, Inc.

Tool life and hole surface integrity studies for hole-making of Ti6Al4V Alloy

With a significant growth in the use of titanium alloys in the aviation manufacturing industry, the key challenge of making high-quality holes in the aircraft assembly process needs to be addressed. In this work, case studies deploying traditional drilling and helical milling technologies are carried out to investigate the tool life and hole surface integrity for hole-making of titanium alloy. Results show that the helical milling process leads to much longer tool life, generally lower hole surface roughness, and higher hole subsurface microhardness. In addition, no plastically deformed layer or white layer has been observed in holes produced by helical milling. In contrast, a slightly softened region was always present on the drilled surface. The residual stress distributions within the hole surface, including compressive and tensile residual stress, have also been investigated in detail.

"Hidden" Social Networks in Behavior Change Interventions

We investigated whether “hidden” (or unobserved) social networks were evident in a 2011 physical activity behavior change intervention in Belfast, Northern Ireland. Results showed evidence of unobserved social networks in the intervention and illustrated how the network evolved over short periods and affected behavior. Behavior change interventions should account for the interaction among participants (i.e., social networks) and how such interactions affect intervention outcome.

Increased Exposure to Rigid Routines can Lead to Increased Challenging Behavior Following Changes to Those Routines

Several neurodevelopmental disorders are associated with preference for routine and challenging behavior following changes to routines. We examine individuals with Prader–Willi syndrome, who show elevated levels of this behavior, to better understand how previous experience of a routine can affect challenging behavior elicited by disruption to that routine. Play based challenges exposed 16 participants to routines, which were either adhered to or changed. Temper outburst behaviors, heart rate and movement were measured. As participants were exposed to routines for longer before a change (between 10 and 80 min; within participants), more temper outburst behaviors were elicited by changes. Increased emotional arousal was also elicited, which was indexed by heart rate increases not driven by movement. Further study will be important to understand whether current intervention approaches that limit exposure to changes, may benefit from the structured integration of flexibility to ensure that the opportunity for routine establishment is also limited.

Mixtures of azepanium based ionic liquids and propylene carbonate as high voltage electrolytes for supercapacitors

This work provides a study of mixtures of the azepanium-based ionic liquid (IL) N-methyl, N-butyl-azepanium bis[(trifluoromethane) sulfonyl]imide (Azp₁₄TFSI) and propylene carbonate (PC) as electrolyte components in electrochemical double layer capacitors (EDLCs). The considered mixtures' properties were then compared to the properties of mixtures of N-butyl, N-methylpyrrolidinium bis[(trifluoromethane) sulfonyl]imide (Pyr₁₄TFSI) and PC in terms of viscosity, conductivity and electrochemical behavior. The mixtures' operative potentials were found to be comparable to each other, leading to operative voltages as high as 3.5 V, while retaining the low viscosities and high conductivities of PC based EDLC electrolytes.