Facilitation of nucleoside and nucleotide chemistry by ball milling

Numerical analysis of impact events in a centrifugal impact pin mill

Milling is an important operation in many industries, such as mining and pharmaceutical. Although the comminution process during milling has been extensively studied, the material fragmentation mechanisms in a mill are still not well understood partly because of the lack of an understanding on the local stressing and dynamic information under operational conditions in mills. This paper presents a DEM simulation of particle dynamics and impact events in a centrifugal impact pin mill. The main focus is the statistical characteristics of the dominant stressing modes during the milling process. The frequency, velocity and force of the different impact events between particles and mill components, or between particles, are analysed. © 2013 AIP Publishing LLC.

2P/Encke, the Taurid complex NEOs and the Maribo and Sutter's Mill meteorites

Aims. 2P/Encke is a short period comet that was discovered in 1786 and has been extensively observed and studied for more than 200years. The Taurid meteoroid stream has long been linked with 2P/Encke owing to a good match of their orbital elements, even thoughthe comet’s activity is not strong enough to explain the number of observed meteors. Various small near-Earth objects (NEOs) havebeen discovered with orbits that can be linked to 2P/Encke and the Taurid meteoroid stream. Maribo and Sutter’s Mill are CM typecarbonaceous chondrite that fell in Denmark on January 17, 2009 and April 22, 2012, respectively. Their pre-atmospheric orbits placethem in the middle of the Taurid meteoroid stream, which raises the intriguing possibility that comet 2P/Encke could be the parentbody of CM chondrites.
Methods. To investigate whether a relationship between comet 2P/Encke, the Taurid complex associated NEOs, and CM chondritesexists, we performed photometric and spectroscopic studies of these objects in the visible wavelength range. We observed 2P/Enckeand 10 NEOs on August 2, 2011 with the FORS instrument at the 8.2 m Very Large Telescope on Cerro Paranal (Chile).
Results. Images in the R filter, used to investigate the possible presence of cometary activity around the nucleus of 2P/Encke andthe NEOs, show that no resolved coma is present. None of the FORS spectra show the 700 nm absorption feature due to hydratedminerals that is seen in the CM chondrite meteorites. All objects show featureless spectra with moderate reddening slopes at λ < 800nm. Apart for 2003 QC10 and 1999 VT25, which show a flatter spectrum, the spectral slope of the observed NEOs is compatible withthat of 2P/Encke. However, most of the NEOs show evidence of a silicate absorption in lower S/N data at λ > 800 nm, which is notseen in 2P/Encke, which suggests that they are not related.
Conclusions. Despite similar orbits, we find no spectroscopic evidence for a link between 2P/Encke, the Taurid complex NEOs andthe Maribo and Sutter’s Mill meteorites. However, we cannot rule out a connection to the meteorites either, as the spectral differencesmay be caused by secondary alteration of the surfaces of the NEOs. 

Scaled Heavy-Ball Acceleration of the Richardson-Lucy Algorithm for 3D Microscopy Image Restoration

The Richardson–Lucy algorithm is one of the most important in image deconvolution. However, a drawback is its slow convergence. A significant acceleration was obtained using the technique proposed by Biggs and Andrews (BA), which is implemented in the deconvlucy function of the image processing MATLAB toolbox. The BA method was developed heuristically with no proof of convergence. In this paper, we introduce the heavy-ball (H-B) method for Poisson data optimization and extend it to a scaled H-B method, which includes the BA method as a special case. The method has a proof of the convergence rateof O(K^2), where k is the number of iterations. We demonstrate the superior convergence performance, by a speedup factor off ive, of the scaled H-B method on both synthetic and real 3D images.

Comparing lateral bias in dogs and humans using the KongTM ball test

The KongTM ball test has been used extensively to assess lateral bias in the domestic dog. Implicit in this challenge is the assumption that dogs use their dominant paw to stabilise the ball. This study examined whether or not this is the case. A comparative approach was adopted, exploring limb use in dogs and humans. In Experiment 1, the paw preference of 48 dogs was assessed on the KongTM ball test. Analysis revealed an equal distribution of paw use, although significantly more dogs were paw-preferent than ambilateral. Significantly more male dogs were classified as right-pawed, while more females were ambilateral. There was no significant effect of canine sex or castration status on the dogs’ paw preferences. In Experiment 2, 94 adult humans were assessed on their ability to remove a piece of paper from a KongTM ball with their mouth, using their left, right or both hands to stabilise the ball. 76% of the right-handed people used their left hand, and 82% of the left-handed participants used their right hand, to hold the KongTM steady. It is concluded that dogs, like humans, are most likely using their non-dominant limb to stabilise the KongTM ball and their dominant side for postural support. This has potential applied implications from an animal welfare perspective.

FEM Analysis to Optimally Design End Mill cutters for Milling of Ti-6Al-4V

This paper presents an FEM analysis conducted for optimally designing end mill cutters through verifying the cutting tool forces and stresses for milling Titanium alloy Ti-6Al-4 V. Initially, the theoretical tool forces are calculated by considering the cutting edge on a cutting tool as the curve of an intersection over a spherical/flat surface based on the model developed by Lee & Altinas [1]. Considering the lowest tool forces the cutting tool parameters are taken and optimal design of end mill is decided for different sizes. Then the 3D CAD models of the end mills are developed and used for Finite Element Method to verify the cutting forces for milling Ti-6Al-4 V. The cutting tool forces, stress, strain concentration (s), tool wear, and temperature of the cutting tool with the different geometric shapes are simulated considering Ti-6Al-4 V as work piece material. Finally, the simulated and theoretical values are compared and the optimal design of cutting tool for different sizes are validated. The present approach considers to improve the quality of machining surface and tool life with effects of the various parameters concerning the oblique cutting process namely axial, radial and tangential forces. Various simulated test cases are presented to highlight the approach on optimally designing end mill cutters.

Feature recognition & tool path generation for 5 axis step-nc machining of free form / irregular contoured surfaces

This research paper presents a five step algorithm to generate tool paths for machining Free form / Irregular Contoured Surface(s) (FICS) by adopting STEP-NC (AP-238) format. In the first step, a parametrized CAD model with FICS is created or imported in UG-NX6.0 CAD package. The second step recognizes the features and calculates a Closeness Index (CI) by comparing them with the B-Splines / Bezier surfaces. The third step utilizes the CI and extracts the necessary data to formulate the blending functions for identified features. In the fourth step Z-level 5 axis tool paths are generated by adopting flat and ball end mill cutters. Finally, in the fifth step, tool paths are integrated with STEP-NC format and validated. All these steps are discussed and explained through a validated industrial component.