Light emission from gold and silver thin films in a scanning tunneling microscope: role of contamination and interpretation of grain structure in photon maps

Scanning tunnelling microscope (STM) tip-induced light emission from Au and Ag has been studied. Thin film samples similar to100nm thick were prepared by thermal evaporation at 0.5nm/s onto a room-temperature glass substrate to produce grains of 20-50nm in lateral dimension at the surface. Light emission from the samples in the STM was quasi-simultaneously recorded with the topography, at 1.8V tip bias and 3-40nA current, alternating pixel by pixel at the same bias. Typically, a surface scan range of 150 nm x 150 nm was surveyed. Au, W and PtIr tips were used.

Effectiveness of different footbath solutions in the treatment of digital dermatitis in dairy cows

Three experiments were conducted to test the effectiveness of different footbath solutions and regimens in the treatment of digital dermatitis (DD) in dairy cows. During the study, groups of cows walked through allocated footbath solutions after milking on 4 consecutive occasions. All cows were scored weekly for DD lesion stage on the hind feet during milking. A “transition grade” was assigned on the basis of whether the DD lesions improved (1) or deteriorated or did not improve (0) from week to week. This grade per cow was averaged for all cows in the group. In experiment 1, 118 cows were allocated to 1 of 3 footbath treatments for 5 wk: (1) 5% CuSO4 each week, (2) 2% ClO- each week, or (3) no footbath (control). The mean transition grade, and proportion of cows without DD lesions at the end of the trial were significantly higher for treatment 1 above (0.36, 0.13, and 0.11, respectively; standard error of the difference, SED=0.057). In experiment 2, 117 cows were allocated to 1 of 4 footbath treatment regimens for 8 wk: (1) 5% CuSO4 each week, (2) 2% CuSO4 each week, (3) 5% CuSO4 each fortnight, or (4) 2% CuSO4 each fortnight. For welfare reasons, cows allocated to the weekly and fortnightly footbath regimens had an average prevalence of >60% and =25% active DD at the start of the trial, respectively. Significantly more cows had no DD lesions (0.53 vs. 0.36, respectively; SED=0.049), and the mean transition grade of DD lesions was higher in the 5% compared with the 2% weekly CuSO4 treatment (0.52 vs. 0.38, respectively; SED=0.066). Similarly, significantly more cows had no DD lesions in the 5% compared with the 2% fortnightly CuSO4 treatments (0.64 vs. 0.47, respectively; SED=0.049). In experiment 3, 95 cows were allocated to 1 of 3 footbath treatments: (1) each week alternating 5% CuSO4 with 10% salt water, (2) each week alternating 5% CuSO4 with water, or (3) 5% CuSO4 each fortnight (control). After 10 wk, more cows had no DD in the salt water treatment than in the control treatment (0.35 vs. 0.26, respectively; SED=0.038), but levels of active lesions were higher for this treatment than in the other 2 treatments (0.17, 0.00, and 0.13, respectively; SED=0.029). Treatment did not affect mean transition grade of DD lesions. In conclusion, CuSO4 was the only footbath solution that was consistently effective for treatment of DD. In cases when DD prevalence was high, a footbath each week using 5% CuSO4 was the most effective treatment.

Linear and nonlinear dynamics of a dust bicrystal consisting of positive and negative dust particles

A dusty plasma crystalline configuration consisting of charged dust grains of alternating charge sign (.../+/-/+/-/+/...) and mass is considered. Both charge and mass of each dust species are taken to be constant. Considering the equations of longitudinal motion, a dispersion relation for linear longitudinal vibrations is derived from first principles and then analyzed. Two harmonic modes are obtained, namely, an acoustic mode and an inverse-dispersive optic-like one. The nonlinear aspects of acoustic longitudinal dust grain motion are addressed via a generalized Boussinesq (and, alternatively, a generalized Korteweg-de Vries) description. (C) 2005 American Institute of Physics.

Stability of dust lattice modes in the presence of charged dust grain polarization in plasmas

We discuss the effect of the attractive force associated with overlapping Debye spheres on the dispersion properties of the longitudinal and transverse dust lattice waves in strongly coupled dust crystals. The dust grain attraction is shown to contribute to a destabilization of the longitudinal dust lattice oscillations. The (optic-like) transverse mode dispersion law is shown to change. due to the Debye sphere dressing effect, from the known inverse-dispersive ("backward wave") form into a normal dispersive law (i.e. the group velocity changes sign). The stability of one-dimensionless bi-layers, consisting of (alternating) negatively and positively charged dust particles, is also discussed. The range of parameter values (mainly in terms of the lattice parameter kappa) where the above predictions are valid, are presented. (c) 2005 Elsevier B.V. All rights reserved.

Timing and trajectory in rhythm production

The Wing-Kristofferson movement timing model (A. M. Wing & A. B. Kristofferson, 1973a, 1973b) distinguishes central timer and motor implementation processes. Previous studies have shown that increases in interresponse interval (IRI) variability with mean IRI are due to central timer processes, not motor implementation. The authors examine whether this is true with IRI duration changes in binary rhythm production. Ten participants provided IRI and movement data in bimanual synchronous tapping under equal (isochronous) and alternating (rhythm) interval conditions. Movement trajectory changes were observed with IRI duration (300, 500, or 833 ms) and for 500-ms IRIs produced in rhythm contexts (300/500 ms, 500/833 ms). However, application of the Wing-Kristofferson model showed that duration and context effects on IRI variability were attributable largely to timer processes with relatively little effect on motor processes.

Novel anti-inflammatory compound SEN1176 alleviates behavioural deficits induced following bilateral intrahippocampal injection of aggregated amyloid-beta(1-42).

Behavioral effects of a novel anti-inflammatory SEN1176 were investigated. This pyrrolo[3,2-e][1,2,4]triazolo[1,5-a]pyrimidine suppresses amyloid-ß (Aß)1-42-induced macrophage production of nitric oxide, TNF-a, IL-1ß, and IL-6 in a dose-dependent fashion, an activity profile consistent with SEN1176 being a neuroinflammation inhibitor. Using male Sprague-Dawley rats, SEN1176 was examined relative to detrimental behavioral effects induced following bilateral intrahippocampal (IH) injections of aggregated Aß1-42. The rats were trained to respond under an alternating-lever cyclic-ratio (ALCR) schedule of food reinforcement, enabling measurement of parameters of operant performance that reflect aspects of learning and memory. Under the ALCR schedule, orally administered SEN1176 at 5, 20, or 30 mg/kg was effective in reducing the behavioral deficit caused by bilateral IH aggregated Aß1-42 injections in a dose-related manner over a 90-day treatment period. SEN1176 at 20 and 30 mg/kg significantly reduced lever switching errors and, at doses of 5, 10, and 30 mg/kg, significantly reduced incorrect lever perseverations, indicating a reduction of the behavioral deficit induced as a result of inflammation following IH Aß1-42 injections. When treatment with SEN1176 was instigated 30 days after IH Aß1-42 injections, it resulted in progressive protection, and withdrawal of SEN1176 treatment 60 days after IH Aß1-42 injections revealed partial retention of the protective effect. SEN1176 also significantly reduced numbers of activated astrocytes adjacent to the aggregated Aß1-42 injection sites. These results indicate the potential of SEN1176 for alleviating chronic neuroinflammatory processes related to brain Aß deposition that affect learning and memory in Alzheimer's disease.

Liquid-liquid slug flow: Hydrodynamics and pressure drop

In this paper, the hydrodynamics and the pressure drop of liquid-liquid slug flow in round microcapillaries are presented. Two liquid-liquid flow systems are considered, viz. water-toluene and ethylene glycol/water-toluene. The slug lengths of the alternating continuous and dispersed phases were measured as a function of the slug velocity (0.03-0.5 m/s), the organic-to-aqueous flow ratio (0.1-4.0), and the microcapillary internal diameter (248 and 498 mu m). The pressure drop is modeled as the sum of two contributions: the frictional and the interface pressure drop. Two models are presented, viz, the stagnant film model and the moving film model. Both models account for the presence of a thin liquid film between the dispersed phase slug and the capillary wall. It is found that the film velocity is of negligible influence on the pressure drop. Therefore, the stagnant film model is adequate to accurately predict the liquid-liquid slug flow pressure drop. The influence of inertia and the consequent change of the slug cap curvature are accounted for by modifying Bretherton's curvature parameter in the interface pressure drop equation. The stagnant film model is in good agreement with experimental data with a mean relative error of less than 7%.

Controlling the response characteristics of luminescent porphyrin plastic film sensors for oxygen

Two porphyrins, platinum(II) octaethylporphyrin (Pt-OEP) and palladium(II) octaethylporphyrin (Pd-OEP), are incorporated into a wide variety of different encapsulating matricies and tested as oxygen sensors, The excited state lifetimes of the two porphyrins are quite different, 0.091 ms for Pt-OEP and 0.99 ms for Pd-OEP, and Pt-OEP-based oxygen sensors are found to be much less sensitive than Pd-OEP-based ones to quenching by oxygen, Two major response characteristics of an oxygen sensor are (i) its sensitivity toward oxygen and (ii) its response and recovery times when exposed to an alternating atmosphere of nitrogen and air. The response characteristics of a rang of Pt-OEP, and Pd-OEP-based oxygen sensors were determined using cellulose acetate butyrate (CAB), poly(methyl methacrylate) (PMMA), and PMMA/CAB polymer blends as the encapsulating media. Pt-OEP and Pd-OEP oxygen sensors have better response characteristics (i.e., more sensitive and lower response and recovery times) when CAB is used as the encapsulating medium rather than PMMA. For both Pt-OEP- and Pd-OEP-based oxygen sensors, in either polymer, increasing the level of tributyl phosphate plasticizer improves the response characteristics of the final oxygen-sensitive film. Pt-OEP in different unplasticized PMMA/CAB blended films produced a range of oxygen sensors in which the response characteristics improved with increasing level of CAB present.

Fluorescence-based thin plastic film ion-pair sensors for oxygen

A general method of preparation of thin-film sensors for O-2, incorporating the dye ion-pair tris(4,7-diphenyl-1,10-phenanthroline) rutheninm(II) ditetraphenylborate, in a variety of different thin film polymer/plasticizer matrices is described, The sensitivity of the sensor depends upon the nature of the polymer matrix and plasticizer, A detailed study of one of these systems utilising the polymer poly(methyl methacrylate), PMMA, is reported. The sensitivity of this O-2 sensor depends markedly upon the plasticizer concentration and is largely independent of temperature (24,5-52.5 degrees C) and age (up to 30 d), When exposed to an alternating atmosphere of O-2 and N-2, a typical oxygen film sensor in PMMA exhibits a 0-90% response and recovery time of 0.4 and 4.5 s, respectively.

Thin plastic film colorimetric sensors for carbon dioxide: Effect of plasticizer on response

Different plasticizers, including phosphate-, phthalate-and adipate-based types were used in the creation of a range of colorimetric plastic film sensors for CO2, The different types of plasticizer used in the formulation of a colorimetric plastic film sensor for CO2 affect the response and recovery times of the sensor differently, An effective plasticizer was taken as one that decreased the response and recovery times of the final film sensor when exposed to an alternating atmosphere of 0-5% CO2. On this basis, the most efficient plasticizers appeared to be phosphate-based, followed by phthalate- and adipate-based plasticizers, This trend appears to reflect the degree of the polymer-plasticizer compatibility. Increasing the amount of plasticizer in the film formulation decreased the response and recovery times of the sensor dramatically, The sensitivity of the film sensor towards CO2 appears to decrease with increasing plasticizer effectiveness; thus, the general order of film CO2 sensitivity with respect to plasticizer type was found to be adipate > phthalate > phosphate. In general, the response of the optical films towards CO2 was found to be temperature sensitive [typically, Delta H = -(44-55) kJ mol(-1)], The phosphate-based plasticized films appear to be less temperature sensitive than the other plasticized films, and 2-ethylhexyl diphenylphosphate appears particularly effective in this respect (Delta H = -18.5 kJ mol(-1)).

FLUORESCENCE PLASTIC THIN-FILM SENSOR FOR CARBON-DIOXIDE

The method of preparation of a novel plastic thin-film sensor that incorporates the fluorescent dye 8-hydroxypryrene-1,3,6-trisulfonic acid is described; the shelf-life of the film is over 6 months. The results of a study on the equilibrium response of the sensor towards different levels of gaseous CO2 fit a model there is a 1 + 1 equilibrium reaction between the deprotonated form of the dye (present in the film as an ion pair) and the concentration of gaseous CO2 present. In contrast to the situation in aqueous solution, in the plastic film the pK(a) of the excited form of the dye appears close to that of the ground-state form, although this does not interfere with its use as 8 CO2 sensor. The 0 to 90% response and recovery times of the film when exposed to an alternating atmosphere of air and 5% CO2 are typically 4.3 and 7.1 s, respectively.

EQUILIBRIUM STUDIES ON COLORIMETRIC PLASTIC FILM SENSORS FOR CARBON-DIOXIDE

The equilibrium responses of three new colorimetric plastic film sensors for CO2 as a function of % CO2 and temperature are described. The results fit a model in which there is a 1:1 equilibrium reaction between the deprotonated form of the dye (present in the film as an ion pair) and CO2. The 0-50% and 0-90% response and recovery times of each of these films when exposed to an alternating atmosphere of air and 5% CO2 are determined and in two cases are typically less than 3 s. The shelf life of the films is long (many months); however, prolonged use of the films leads to the permanent generation of the protonated form of the dye over a period of 20-100 h. A possible cause of this latter effect is discussed.

Coherent Control of High Harmonic Generation via Dual-Gas Multijet Arrays

High harmonic generation (HHG) is a central driver of the rapidly growing field of ultrafast science. We present a novel quasiphase-matching (QPM) concept with a dual-gas multijet target leading, for the first time, to remarkable phase control between multiple HHG sources (> 2) within the Rayleigh range. The alternating jet structure with driving and matching zones shows perfect coherent buildup for up to six QPM periods. Although not in the focus of the proof-of-principle studies presented here, we achieved competitive conversion efficiencies already in this early stage of development.

Reappraisal of the type species of Polysiphonia (Rhodomelaceae, Rhodophyta)

The genus Polysiphonia Greville, nom. cons., has had a long and confused nomenclatural history. At present, Polysiphonia has a wide circumscription, including at least 200 species, but it is heterogeneous in many vegetative and reproductive developmental features. Central to any re-evaluation of the genus is a detailed examination of the type species of Polysiphonia, P. urceolata (Lightfoot ex Dillwyn) Greville, which is conspecific with P. stricta (Dillwyn) Greville. We here report on the vegetative and reproductive morphology of P. stricta, including P, urceolata, based on type and other material from the British Isles. Thalli consist of prostrate and erect ecorticate axes with four pericentral cells, attached by unicellular rhizoids remaining in open connection with pericentral cells. Prostrate axes lack vegetative trichoblasts; trichoblasts occur seasonally on erect axes. Branch initials are cut off from the subapical cell at intervals of four or five segments in dichotomous and alternating pairs rather than being formed horn each axial cell in the spiral pattern typical of most species of Polysiphonia. Spermatangial branch initials, which are trichoblast homologues, are produced directly from each axial cell at the tips of erect branches, not subtended by trichoblasts, and have two- to five-celled sterile tips when mature. The mature carpogonial branch is four-celled with a two-celled first sterile group and a one-celled second sterile group. Following presumed fertilization, direct fusion apparently takes place between carpogonium and auxiliary tell; mature cystocarps are usually urceolate. Tetrasporangia are formed from the third pericentral cell, in straight series, and have two pre-sporangial cover cells. Previous accounts of a third, post-sporangial cover cell could not be substantiated. P. stricta and a small group of other Polysiphonia species differ in several important respects from most members of the genus, which have rhizoids cut off from pericentral cells by a cell division, abundant trichoblasts, spirally arranged tetrasporangia and a post-sporangial cover cell. The branching pattern of P. stricta highlights the difficulties of distinguishing between the tribes Polysiphonieae and Pterosiphonieae.

Abeta oligomer toxicity inhibitor protects memory in models of synaptic toxicity

BACKGROUND AND PURPOSE:

Amyloid-ß (Aß) aggregation into synaptotoxic, prefibrillar oligomers is a major pathogenic event underlying the neuropathology of Alzheimer's disease (AD). The pharmacological and neuroprotective properties of a novel Aß aggregation inhibitor, SEN1269, were investigated on aggregation and cell viability and in test systems relevant to synaptic function and memory, using both synthetic Aß(1-42) and cell-derived Aß oligomers.
EXPERIMENTAL APPROACH:

Surface plasmon resonance studies measured binding of SEN1269 to Aß(1-42) . Thioflavin-T fluorescence and MTT assays were used to measure its ability to block Aß(1-42) -induced aggregation and reduction in cell viability. In vitro and in vivo long-term potentiation (LTP) experiments measured the effect of SEN1269 on deficits induced by synthetic Aß(1-42) and cell-derived Aß oligomers. Following i.c.v. administration of the latter, a complex (alternating-lever cyclic ratio) schedule of operant responding measured effects on memory in freely moving rats.
KEY RESULTS:

SEN1269 demonstrated direct binding to monomeric Aß(1-42) , produced a concentration-related blockade of Aß(1-42) aggregation and protected neuronal cell lines exposed to Aß(1-42) . In vitro, SEN1269 alleviated deficits in hippocampal LTP induced by Aß(1-42) and cell-derived Aß oligomers. In vivo, SEN1269 reduced the deficits in LTP and memory induced by i.c.v. administration of cell-derived Aß oligomers.
CONCLUSIONS AND IMPLICATIONS:

SEN1269 protected cells exposed to Aß(1-42) , displayed central activity with respect to reducing Aß-induced neurotoxicity and was neuroprotective in electrophysiological and behavioural models of memory relevant to Aß-induced neurodegeneration. It represents a promising lead for designing inhibitors of Aß-mediated synaptic toxicity as potential neuroprotective agents for treating AD.