Clarification of rubber mill wastewater by a plant based biopolymer- comparison with common inorganic coagulants

Background: In this study, the efficiency of Guar gum as a biopolymer has been compared with two other widely used inorganic coagulants, ferric chloride (FeCl3) and aluminum chloride (AlCl3), for the treatment of effluent collected from the rubber-washing tanks of a rubber concentrate factory. Settling velocity distribution curves were plotted to demonstrate the flocculating effect of FeCl3, AlCl3 and Guar gum. FeCl3 and AlCl3 displayed better turbidity removal than Guar gum at all settling velocities.

Result: FeCl3, AlCl3 and Guar gum removed 92.8%, 88.2% and 88.1% turbidity, respectively, of raw wastewater at a settling velocity of 0.1 cm min-1, respectively. Scanning electron microscopic (SEM) study conducted on the flocs revealed that Guar gum and FeCl3produced strong intercoiled honeycomb patterned floc structure capable of entrapping suspended particulate matter. Statistical experimental design Response Surface Methodology (RSM) was used to design all experiments, where the type and dosage of flocculant, pH and mixing speed were taken as control factors and, an optimum operational setting was proposed.

Conclusion: Due to biodegradability issues, the use of Guar gum as a flocculating agent for wastewater treatment in industry is highly recommended.

A comparative study of biopolymers and alum in the separation and recovery of pulp fibres from paper mill effluent by flocculation

Recovery of cellulose fibres from paper mill effluent has been studied using common polysaccharides or biopolymers such as Guar gum, Xanthan gum and Locust bean gum as flocculent. Guar gum is commonly used in sizing paper and routinely used in paper making. The results have been compared with the performance of alum, which is a common coagulant and a key ingredient of the paper industry. Guar gum recovered about 3.86 mg/L of fibre and was most effective among the biopolymers. Settling velocity distribution curves demonstrated that Guar gum was able to settle the fibres faster than the other biopolymers; however, alum displayed the highest particle removal rate than all the biopolymers at any of the settling velocities. Alum, Guar gum, Xanthan gum and Locust bean gum removed 97.46%, 94.68%, 92.39% and 92.46% turbidity of raw effluent at a settling velocity of 0.5 cm/min, respectively. The conditions for obtaining the lowest sludge volume index such as pH, dose and mixing speed were optimised for guar gum which was the most effective among the biopolymers. Response surface methodology was used to design all experiments, and an optimum operational setting was proposed. The test results indicate similar performance of alum and Guar gum in terms of floc settling velocities and sludge volume index. Since Guar gum is a plant derived natural substance, it is environmentally benign and offers a green treatment option to the paper mills for pulp recycling.

Impact of prosthodontic rehabilitation on the chewing efficiency of partially dentate older patients

Objectives: This study compared two tooth replacement strategies for partially dentate older patients namely; removable partial dentures (RPDs) and functionally orientated treatment based on the shortened dental arch (SDA) concept. Patients were compared in terms of chewing efficiency after prosthodontic rehabilitation. Methods: Chewing efficiency was assessed electronically by a two-colour gum-mixing test. Specimens were assembled from two different colours of chewing gums with a size of 30 x 18 x 3 mm. After participants chewed for 20 cycles, the gum was retrieved, flattened to a 1-mm-thick wafer, and digitized with a flatbed image scanner. The pixels of unmixed colour in the specimen were counted by means of Adobe Photoshop 2.0R software (Adobe Systems, San Jose, CA, USA), and the ratio to the pixels of the entire frame was computed. This ratio is called the Unmixed Fraction (UF). The more efficiently the specimen is chewed, the less unmixed colour remains, and the smaller the gum becomes. Consequently, a low unmixed fraction corresponds to good chewing efficiency. Results: 32 patients completed the chewing efficiency test (17 RPDs and 15 SDA). The mean UF recorded for the SDA group was not significantly different to that recorded for the RPD group (p>0.05, unpaired t-test). Conclusion: These results indicate that prosthodontic rehabilitation according to the principles of the SDA is equivalent to RPDs in terms of restoration of chewing ability for partially dentate older patients.