An Investigation Into Improving Off-Design Performance in a Turbocharger Turbine Utilizing Non-Radial Blading

Off-design performance now plays a vital role in the design decisions made for automotive turbocharger turbines. Of particular interest is extracting more energy at high pressure ratios and lower rotational speeds. In this region of operation the U/C value will be low and the rotor will experience high values of positive incidence at the inlet. The positive incidence causes flow to separate on the suction surface and produces high blade loading at inlet, which drives tip leakage. A CFD analysis has been carried out on a number of automotive turbines utilizing non-radial fibred blading. To help improve secondary flows yet meet stress requirements a number of designs have been investigated. The inlet blade angle has been modified in a number of ways. Firstly, the blading has been adjusted as to provide a constant back swept angle in the span wise direction. Using the results of the constant back swept blading studies, the back swept blade angle was then varied in the span wise direction. In addition to this, in an attempt to avoid an increase in stress, the effect of varying the leading edge profile of the blade was investigated. It has been seen that off-design performance is improved by implementing back swept blading at the inlet. Varying the inlet angle in the span wise direction provided more freedom for meeting stress requirements and reduces the negative impact on blade performance at the design point. The blade leading edge profile was seen to offer small improvements during off-design operation with minimal effects on stress within the rotor. However, due to the more pointed nature of the leading edge, the rotor was less tolerant to flow misalignment at the design point.

Experimental and Numerical Benchmarking of an Improved Impeller Meanline Modelling Method for Automotive Turbocharger Centrifugal Compressors

After the development of a new single-zone meanline modelling technique, benchmarking of the technique and the modelling methods used during its development are presented. The new meanline model had been developed using the results of three automotive turbocharger centrifugal compressors, and single passage CFD models based on their geometry.

The target of the current study was to test the new meanline modelling method on two new centrifugal compressor stages, again from the automotive turbocharger variety. Furthermore the single passage CFD modelling method used in the previous study would be again employed here and also benchmarked.

The benchmarking was twofold; firstly test the overall performance prediction accuracy of the single-zone meanline model. Secondly, test the detailed performance estimation of the CFD model using detailed interstage static pressure tappings.

The final component of this study exposed the weaknesses in the current modelling methods used (explicitly during this study). The non-axisymmetric flow field at the leading and trailing edges for the two compressors was measured and is presented here for the complete compressor map, highlighting the distortion relative to the tongue.

Fitness reduction and potential extinction of wild populations of Atlantic salmon, Salmo salar, as a result of interactions with escaped farm salmon.

The high level of escapes from Atlantic salmon farms, up to two million fishes per year in the North Atlantic, has raised concern about the potential impact on wild populations. We report on a twogeneration experiment examining the estimated lifetime successes, relative to wild natives, of farm, F1 and F2 hybrids and BC1 backcrosses to wild and farm salmon. Offspring of farm and hybrids (i.e. all F1 , F2 and BC1 groups) showed reduced survival compared with wild salmon but grew faster as juveniles and displaced wild parr, which as a group were significantly smaller. Where suitable habitat for these emigrant parr is absent, this competition would result in reduced wild smolt production. In the experimental conditions, where emigrants survived downstream, the relative estimated lifetime success ranged from 2% (farm) to 89% (BC1 wild) of that of wild salmon, indicating additive genetic variation for survival . Wild salmon primarily returned to fresh water after one sea winter (1SW) but farm and hybrids produced proportionately more 2SW salmon. However, lower overall survival means that this would result in reduced recruitment despite increased 2SW fecundity. We thus demonstrate that interaction of farm with wild salmon results in lowered fitness, with repeated escapes causing cumulative fitness depression and potentially an extinction vortex in vulnerable populations.

Non-shivering thermogenesis in common spiny mice Acomys cahirinus from adjacent habitats: response to seasonal acclimatization and salinity acclimation

1. We compared resting metabolic rate (RMR) and non-shivering thermogenesis (NST) values between founder and F1-populations of winter-acclimatized Acomys cahirinus that originated from north- and south-facing slopes (NFS and SFS) of the same valley, representing mesic and xeric habitats. 2. NST was measured by the increase in oxygen consumption (VO2) and body temperature (T-b) after a noradrenaline (NA) injection (VO2 NA, TbNA). 3. Body mass and TbNA values were higher in SFS F1-mice, while RMR and VO2 NA values were higher in NFS F1-mice. Differences were not apparent in founders. 4. Results are consistent with NFS and SFS mice being considered as

An Investigation of Compressor Map Width Enhancement and a Detailed Analysis of Inducer Flow Field

This paper describes an investigation of various shroud bleed slot configurations of a centrifugal compressor using CFD with a manual multi-block structured grid generation method. The compressor under investigation is used in a turbocharger application for a heavy duty diesel engine of approximately 400 hp. The baseline numerical model has been developed and validated against experimental performance measurements. The influence of the bleed slot flow field on a range of operating conditions between surge and choke has been analysed in detail.
The impact of the returning bleed flow on the incidence at the impeller blade leading edge due to its mixing with the main through-flow has also been studied. From the baseline geometry, a number of modifications to the bleed slot width have been proposed, and a detailed comparison of the flow characteristics performed. The impact of slot variations on the inlet incidence angle has been investigated, highlighting the improvement in surge and choked flow capability. Along with this, the influence of the bleed slot on stabilising the blade passage flow by the suction of the tip and over-tip vortex flow by the slot has been considered near surge.

An Impact Of Various Shroud Bleed Slot Configurations And Cavity Vanes On Compressor Map Width And The Inducer Flow Field

This paper describes an investigation of map width enhancement and a detailed analysis of the inducer flow field due to various bleed slot configurations and vanes in the annular cavity of a turbocharger centrifugal compressor. The compressor under investigation is used in a turbocharger application for a heavy duty diesel engine of approximately 400 hp. This investigation has been undertaken using a computational fluid dynamics (CFD) model of the full compressor stage, which includes a manual multiblock-structured grid generation method. The influence of the bleed slot flow on the inducer flow field at a range of operating conditions has been analyzed, highlighting the improvement in surge and choked flow capability. The impact of the bleed slot geometry variations and the inclusion of cavity vanes on the inlet incidence angle have been studied in detail by considering the swirl component introduced at the leading edge by the recirculating flow through the slot. Further, the overall stage efficiency and the nonuniform flow field at the inducer inlet have been also analyzed. The analysis revealed that increasing the slot width has increased the map width by about 17%. However, it has a small impact on the efficiency, due to the frictional and mixing losses. Moreover, adding vanes in the cavity improved the pressure ratio and compressor performance noticeably. A detail analysis of the compressor with cavity vanes has also been presented.

Inherited resistance to arsenate toxicity in two populations of Lumbricus rubellus

No unequivocal evidence exists of genetically inherited resistance to metals/metalloids in field populations of earthworms. We studied cocoon production in adult Lumbricus rubellus Hoffmeister collected from an abandoned arsenic and copper mine (Devon Great Consols, Devon, UK), and abandoned tungsten mine (Carrock Fell, Cumbria, UK) and an uncontaminated cultured population. The earthworms were kept in uncontaminated soil for nine weeks. From a total of 42 L. rubellus from each site, Devon Great Consols adults produced 301 cocoons, of which 42 were viable; Carrock Fell 60 cocoons, of which 11 were viable; and the reference population 101 cocoons, of which 62 were viable. The hatchlings were collected and stored at 4 degrees C at weekly intervals. After 12 weeks, all hatchlings were transferred to clean soil and maintained at 15 degrees C for 20 weeks until they showed evidence of a clitellum. In toxicity trials, F1 generation L. rubellus were exposed to 2,000 mg As/kg as sodium arsenate or 300 mg Cu/kg as copper chloride for 28 d. The F1 generation L. rubellus from Devon Great Consols mine demonstrated resistance to arsenate but not copper. All L. rubellus from Devon Great Consols kept in soil treated with sodium arsenate remained in good condition over the 28-d period but lost condition rapidly and suffered high mortality in soil treated with copper chloride. The control population suffered high mortality in soil treated with sodium arsenate and copper chloride. Previous work has shown that field-collected adults demonstrate resistance to both arsenate and Cu toxicity under these conditions. Thus, while arsenate resistance may be demonstrated in F1 generation L. rubellus from one of the contaminated sites, Cu resistance is not. The F1 adults and F2 cocoons did not have significantly higher levels of As than the control population, with no residual As tissue burden, suggesting that resistance to As in these populations may be inherited.

Prevalence and Causes of Prescribing ErrorsL The PRescribing Outcomes for Trainee Doctors Engaged in Clinical Training (PROTECT) Study

Objectives: Study objectives were to investigate the prevalence and causes of prescribing errors amongst foundation doctors (i.e. junior doctors in their first (F1) or second (F2) year of post-graduate training), describe their knowledge and experience of prescribing errors, and explore their self-efficacy (i.e. confidence) in prescribing.

Method: A three-part mixed-methods design was used, comprising: prospective observational study; semi-structured interviews and cross-sectional survey. All doctors prescribing in eight purposively selected hospitals in Scotland participated. All foundation doctors throughout Scotland participated in the survey. The number of prescribing errors per patient, doctor, ward and hospital, perceived causes of errors and a measure of doctors’ self-efficacy were established.

Results: 4710 patient charts and 44,726 prescribed medicines were reviewed. There were 3364 errors, affecting 1700 (36.1%) charts (overall error rate: 7.5%; F1:7.4%; F2:8.6%; consultants:6.3%). Higher error rates were associated with : teaching hospitals (p,0.001), surgical (p = ,0.001) or mixed wards (0.008) rather thanmedical ward, higher patient turnover wards (p,0.001), a greater number of prescribed medicines (p,0.001) and the months December and June (p,0.001). One hundred errors were discussed in 40 interviews. Error causation was multi-factorial; work environment and team factors were particularly noted. Of 548 completed questionnaires (national response rate of 35.4%), 508 (92.7% of respondents) reported errors, most of which (328 (64.6%) did not reach the patient. Pressure from other staff, workload and interruptions were cited as the main causes of errors. Foundation year 2 doctors reported greater confidence than year 1 doctors in deciding the most appropriate medication regimen.

Conclusions: Prescribing errors are frequent and of complex causation. Foundation doctors made more errors than other doctors, but undertook the majority of prescribing, making them a key target for intervention. Contributing causes included work environment, team, task, individual and patient factors. Further work is needed to develop and assess interventions that address these.

How Prepared are UK Medical Graduates for Practice? Final report from a programme of research commissioned by the General Medical Council

This programme of research aimed to understand the extent to which current UK medical graduates are prepared for practice. Commissioned by the General Medical Council, we conducted: (1) A Rapid Review of the literature between 2009 and 2013; (2) narrative interviews with a range of stakeholders; and (3) longitudinal audio-diaries with Foundation Year 1 doctors. The Rapid Review (RR) resulted in data from 81 manuscripts being extracted and mapped against a coding framework (including outcomes from Tomorrow's Doctors (2009) (TD09)). A narrative synthesis of the data was undertaken. Narrative interviews were conducted with 185 participants from 8 stakeholder groups: F1 trainees, newly registered trainee doctors, clinical educators, undergraduate and postgraduate deans and foundation programme directors, other healthcare professionals, employers, policy and government and patient and public representatives. Longitudinal audio-diaries were recorded by 26 F1 trainees over 4 months. The data were analysed thematically and mapped against TD09. Together these data shed light onto how preparedness for practice is conceptualised, measured, how prepared UK medical graduates are for practice, the effectiveness of transition interventions and the currently debated issue of bringing full registration forward to align with medical students’ graduation. Preparedness for practice was conceptualised as both a long- and short-term venture that included personal readiness as well as knowledge, skills and attitudes. It has mainly been researched using self-report measures of generalised incidents that have been shown to be problematic. In terms of transition interventions: assistantships were found to be valuable and efficacious for proactive students as team members, shadowing is effective when undertaken close to employment/setting of F1 post and induction is generally effective but of inconsistent quality. The August transition was highlighted in our interview and audio-diary data where F1s felt unprepared, particularly for the step-change in responsibility, workload, degree of multitasking and understanding where to go for help. Evidence of preparedness for specific tasks, skills and knowledge was contradictory: trainees are well prepared for some practical procedures but not others, reasonably well prepared for history taking and full physical examinations, but mostly unprepared for adopting an holistic understanding of the patient, involving patients in their care, safe and legal prescribing, diagnosing and managing complex clinical conditions and providing immediate care in medical emergencies. Evidence for preparedness for interactional and interpersonal aspects of practice was inconsistent with some studies in the RR suggesting graduates were prepared for team working and communicating with colleagues and patients, but other studies contradicting this. Interview and audio-diary data highlights concerns around F1s preparedness for communicating with angry or upset patients and relatives, breaking bad news, communicating with the wider team (including interprofessionally) and handover communication. There was some evidence in the RR to suggest that graduates were unprepared for dealing with error and safety incidents and lack an understanding of how the clinical environment works. Interview and audio-diary data backs this up, adding that F1s are also unprepared for understanding financial aspects of healthcare. In terms of being personally prepared, RR, interview and audio diary evidence is mixed around graduates’ preparedness for identifying their own limitations, but all data points to graduates’ difficulties in the domain of time management. In terms of personal and situational demographic factors, the RR found that gender did not typically predict perceptions of preparedness, but graduates from more recent cohorts, graduate entry students, graduates from problem based learning courses, UK educated graduates and graduates with an integrated degree reported feeling better prepared. The longitudinal audio-diaries provided insights into the preparedness journey for F1s. There seems to be a general development in the direction of trainees feeling more confident and competent as they gain more experience. However, these developments were not necessarily linear as challenging circumstances (e.g. new specialty, new colleagues, lack of staffing) sometimes made them feel unprepared for situations where they had previously indicated preparedness.

UK medical graduates’ preparedness for practice (P4P): A multi-site qualitative study

Introduction Previous research has demonstrated mixed findings in terms of graduates’ P4P in terms of their knowledge and skills, and interpersonal, systemic and technological aspects (Monrouxe et al. 2014). Few studies have included diverse stakeholders from multiple sites and employing longitudinal methods. We therefore aimed to understand the extent to which UK medical graduates are prepared for practice as Foundation doctors. Methods Cross-sectional qualitative narrative interview and longitudinal audio-diary (LAD) studies with participants from England, Scotland, Wales and Northern Ireland. Study 1 comprised 27 group and 84 individual interviews (n=185) with participants representing different stakeholders (F1s, fully registered trainees, clinical educators, undergraduate/postgraduate deans/foundation programme directors, other healthcare professionals, employers, policy makers, government representatives, and patient/public representatives). Study 2 comprised LADs with 26 F1s over 4-months. Results Participants found it hard initially to conceptualise the term ‘preparedness for practice’. We identified 2187 personal incident narratives (i.e. stories of P4P experiences) across our data: 506 (23%) were classed as ‘prepared’, 730 (33%) as ‘unprepared’ and 951 (44%) as ‘unspecified’. We identified factors that facilitated (e.g. supportive supervisors/colleagues, opportunities for shadowing) and hindered (e.g. unsupportive or disrespectful colleagues, poor organization, understaffing) transitions into and through the Foundation programme. The LADs suggested that trainees felt more confident and competent over time, but that such development was not always linear as challenging circumstances (e.g. new rotations) sometimes made trainees feel unprepared for situations where they had previously indicated preparedness. Conclusion Our findings add to the existing evidence on medical graduates’ P4P in the UK (e.g. Goldacre et al. 2008; Illing et al. 2013). Our findings support the role of assistantships and supportive supervisors for smoothing transitions from student to F1. Further longitudinal and action research studies are now needed to follow students through their final-year assistantships and into their F2 year.

A numerical study of trailing edge geometry for low inertia automotive mixed flow turbines

Abstract. Mixed flow turbines can offer improvements over typical radial turbines used in automotive turbochargers, with respect to transient performance and low velocity ratio efficiency. Turbine rotor mass dominates the rotating inertia of the turbocharger’s rotating assembly, and any reductions of mass in the outer radii of the wheel, including the rotor back-disk, can significantly reduce this inertia and improve the acceleration of the assembly. Off-design, low velocity ratio conditions are typified by highly tangential flow at the rotor inlet and a non-zero inlet blade angle is desirable for such operating conditions. This is achievable in a Mixed Flow Turbine without increasing bending stresses within the rotor blade, which is beneficial in high speed and high inlet temperature turbine designs.
This study considers the meridional geometry of Mixed Flow Turbines using a multi-disciplinary study to assess both the structural and aerodynamic performance of each rotor, incorporating both CFD and FEA. Variations of rotor trailing edge were investigated at different operating conditions representing both on- and off-design operation within the constraints of existing hardware geometries. In all cases, the performance is benchmarked against an existing state-of-the-art radial turbocharger turbine with consideration of rotor inertia and its benefit for engine transient performance. The results indicate the influence of these parameters and this report details their benefits with respect to turbocharging a downsized, automotive engine.

The signature of fine scale local adaptation in Atlantic salmon revealed from common garden experiments in nature

Understanding the extent, scale and genetic basis of local adaptation is important for conservation and management. Its relevance in salmonids at microgeographic scales, where dispersal (and hence potential gene flow) can be substantial, has however been questioned. Here we compare the fitness of communally-reared offspring of local and foreign Atlantic salmon Salmo salar from adjacent Irish rivers and reciprocal F1 hybrid crosses between them, in the wild ‘home’ environment of the local population. Experimental groups did not differ in wild smolt output but a catastrophic flood event may have limited our ability to detect freshwater performance differences, which were evident in a previous study. Foreign parr exhibited higher, and hybrids intermediate, emigration rates from the natal stream relative to local parr, consistent with genetically-based behavioural differences. Adult return rates were lower for the foreign compared to the local group. Overall lifetime success of foreigners and hybrids relative to locals was estimated at 31% and 40% (mean of both hybrid groups), respectively. The results imply a genetic basis to fitness differences among populations separated by only 50km, driven largely by variation in smolt to adult return rates. Hence even if supplementary stocking programs obtain broodstock from neighbouring rivers, the risk of extrinsic outbreeding depression may be high.

A 1-D Vaneless Diffuser Model Accounting for the Effects of Spanwise Flow Stratification

The radial vaneless diffuser, though comparatively simple in terms of geometry, poses a significant challenge in obtaining an accurate 1-D based performance prediction due to the swirling, unsteady and distorted nature of the flow field. Turbocharger compressors specifically, with the ever increasing focus on achieving a wide operating range, have been recognised to operate with significant regions of spanwise separated flow, particularly at off design conditions.
Using a combination of single passage Computational Fluid Dynamics (CFD) simulations and extensive gas stand test data for three geometries, the current study aims to evaluate the onset and impact of spanwise flow stratification in radial vaneless diffusers, and how the extent of the aerodynamic blockage presented to the flow throughout the diffuser varies with both geometry and operating condition. Having analysed the governing performance parameters and flow phenomena, a novel 1-D modelling method is presented and compared to an existing baseline method as well as test data to quantify the improvement in prediction accuracy achieved.