High temperature thermal stability investigations of ammonium sulphide passivated InGaAs and interface formation with Al2O3 studied by synchrotron radiation based photoemission

High resolution synchrotron radiation core level photoemission measurements have been used to undertake a comparative study ofthe high temperature thermal stability ofthe ammonium sulphide passivated InGaAs surface and the same surface following the atomic layer deposition (ALD) of an ultrathin (∼1 nm) Al2O3 layer. The solution based ex situ sulphur passivation was found to be effective at removing a significant amount of the native oxides and protecting the surface against re-oxidation upon air exposure. The residual interfacial oxides which form between sulphur passivated InGaAs and the ultrathin Al2O3 layer can be substantially removed at high temperature (up to 700 ◦C) without impacting on the InGaAs stoichiometry while significant loss of indium was recorded at this temperature on the uncovered sulphur passivated InGaAs surface.

Development of release methods for critically endangered freshwater pearl mussels (Margaritifera margaritifera)

Biodiversity loss is a global problem with freshwater bivalves considered amongst the most
endangered biota. The freshwater pearl mussel, Margaritifera margaritifera, is declining
throughout its range owing to habitat degradation and overexploitation. In most of its range,
populations are regarded as reproductively non-functional which has led to the development
of captive breeding programmes. A novel method of releasing M. margaritifera was trialled,
with captive-bred juveniles being released into the rivers caged in ‘mussels silos’ (protective
concrete domes with ventilation creating upwelling to ensure water through flow). We
released 240 juvenile mussels and survival and growth rates were monitored for 18 months
post-release for three size classes: A (13.01-20.00mm); B (10.01-13.00mm); and C (4.01-
10.00mm). We explicitly tested two experimental treatments; one where sediment was added
to each silo (allowing mussels to orientate and burrow) and one without sediment. Survival
by the end of the experiment at month 18 was significantly higher for the largest size class at
97% (though growth was lowest in this cohort), and lowest for the smallest size class at 61%
(though growth was highest in this cohort). Survival and growth were unaffected by the
experimental treatment suggesting that adding sediment offered no advantage. Growth was
positively correlated with both water temperature and the particle size of suspended solids
(both of which were collinear, peaking in summer). There are a large number of ex situ
breeding programmes for freshwater pearl mussels throughout Europe and our finding
suggest that the use of ‘mussel silos’ could be a useful tool to protecting juvenile mussels
allowing them to be released at a relatively early stage of development, minimising the risk of
domestication.

Characterisation of fluidised bed granulation processes using in situ Raman spectroscopy

Previous work by the authors Walker et al. [2007b. Fluidised bed characterisation using Raman spectroscopy: applications to pharmaceutical processing. Chemical Engineering Science 62, 3832–3838] illustrated that Raman spectroscopy could be used to provide 3-D maps of the concentration and chemical structure of particles in motion in a fluidised bed, within a relatively short (120 s) time window. Moreover, we reported that the technique, as outlined, has the potential to give detailed in-situ information on how the structure and composition of granules/powders within the fluidised bed (dryer or granulator) vary with the position and evolve with time. In this study we extended the original work by shortening the time window of the Raman spectroscopic analysis to 10 s, which has allowed the in-situ real-time characterisation of a fluidised bed granulation process. Here we show an important new use of the technique which allows in-situ measurement of the composition of the material within the fluidised bed in three spatial dimensions and as a function of time. This is achieved by recording Raman spectra using a probe positioned within the fluidised bed on a long-travel x–y–z stage. In these experiments the absolute Raman intensity is used to provide a direct measure of the amount of any given material in the probed volume, i.e. a particle density. Particle density profiles have been calculated over the granulation time and show how the volume of the fluidised bed decreases with an increase mean granule size. The Raman spectroscopy analysis indicated that nucleation/coalescence in this co-melt fluidised hot melt granulation system occurred over a relatively short time frame (t<30 s). The Raman spectroscopic technique demonstrated accurate correlation with independent granulation experiments which provided particle size distribution analysis. The similarity of the data indicates that the Raman spectra accurately represent solids ratios within the bed, and thus the techniques quantitative capabilities for future use in the pharmaceutical industry.

Fluidised bed characterisation using Raman spectroscopy: Applications to pharmaceutical processing

This study investigates a model system for potential pharmaceutical materials in fluidised bed processes. In particular, this study proposes a novel use of Raman spectroscopy, which allows in situ measurement of the composition of the material within the fluidised bed in three spatial dimensions and as a function of time. This is achieved by recording Raman spectra from specific volumes of space. The work shows that Raman spectroscopy can be used to provide 3D maps of the concentration and chemical structure of the particles in a fluidised bed within a relatively short (120 s) time window. At the most basic level the technique measures particle density via the intensity of the Raman spectra, however this could be used. More importantly the data are also rich in spectroscopic information on the chemical structure of the fluidised particles which is useful either for monitoring a given granulation process or more generally for the analysis of the dynamics of the airflow if the data were incorporated into an appropriate model. The technique has the potential to give detailed in situ information on how the structure and composition of the granules/powders within the fluidised bed (dryer or granulator) vary with the position and evolve with time. (c) 2007 Elsevier Ltd. All rights reserved.