The cost of water from an autonomous wave-powered desalination plant

A techno-economic model of an autonomous wave-powered desalination plant is developed and indicates that fresh water can be produced for as little as £0.45/m3. The advantages of an autonomous wave-powered desalination plant are also discussed indicating that the real value of the system is enhanced due to its flexibility for deployment and reduced environmental impact. The modelled plant consists of the Oyster wave energy converter, conventional reverse osmosis membranes and a pressure exchanger–intensifier for energy recovery. A time-domain model of the plant is produced using wave-tank experimentation to calibrate the model of Oyster, manufacturer's data for the model of the reverse osmosis membranes and a hydraulic model of the pressure exchanger–intensifier. The economic model of the plant uses best-estimate cost data which are reduced to annualised costs to facilitate the calculation of the cost of water. Finally, the barriers to the deployment of this technology are discussed, but they are not considered insurmountable.

Survival of laboratory-reared juvenile European lobster (Homarus gammarus) from three brood sources in southwestern Norway

Experiments were carried out from June 2000 to April 2001 to compare survival of European lobster (Homarus gammarus) offspring (larvae and juveniles) from three brood sources, Kvitsøy Wild (KW), Kvitsøy Cultured (KC), and Rogaland Wild (RW), Norway. In the first set of experiments, newly hatched larvae (stage I) were raised in separate family tanks. All larvae groups survived to stage III/IV, although large variation in relative survival was observed among families within each of the three different female groups. Highest overall survival was observed for the RW group (12.8%), whereas no differences in overall survival were found between the KW (9.0%) and KC groups (9.6%). From stage III/IV, larvae from single family tank experiments were mixed in five “common garden” juvenile experiments. These lasted for 9 months, and the surviving juveniles were identified to family/female group using microsatellite DNA profiling. Significantly higher survival of the KW families (7.0%) was found compared with the KC (3.7%) and the RW families (3.2%), and differences in family ranking of relative survival values were evident between the KW and KC groups. The relative survival rate of the different groups was independent of female lobster size. An estimate based on only stage IV larvae reduced the difference in survival between the KW (11.4%) and KC (8.3%) group. The experiments provided evidence that cultured females (KC) are producing viable offspring with lower, but comparable survival to that of offspring from wild females (KW).

Nociception or pain in a decapod crustacean?

Nociception is the ability to perceive a noxious stimulus and react in a re flexive manner and occurs across a wide range of taxa. However, the ability to experience the associated aversive sensation and feeling, known as pain, is not widely accepted to occur in nonvertebrates. We examined the responses of a decapod crustacean, the prawn, Palaemon elegans, to different noxious stimuli applied to one antenna to assess reflex responses (nociception) and longer-term, specifically directed behavioural responses that might indicate pain. We also examined the effects of benzocaine, a local anaesthetic, on these responses. Noxious stimuli elicited an immediate reflex tail flick response, followed by two prolonged activities, grooming of the antenna and rubbing of the antenna against the side of the tank, with both activities directed specifically at the treated antenna. These responses were inhibited by benzocaine; however, benzocaine did not alter general swimming activity and thus the decline in grooming and rubbing is not due to general anaesthesia. Mechanical stimulation by pinching also resulted in prolonged rubbing, but this was not inhibited by benzocaine. These results indicate an awareness of the location of the noxious stimuli, and the prolonged complex responses indicate a central involvement in their organization. The inhibition by a local anaesthetic is similar to observations on vertebrates and is consistent with the idea that these crustaceans can experience pain.

Analysis of transduction in wastewater bacterial populations by targeting the phage-derived 16S rRNA gene sequences

Bacterial 16S rRNA genes transduced by bacteriophages were identified and analyzed in order to estimate the extent of the bacteriophage-mediated horizontal gene transfer in the wastewater environment. For this purpose, phage and bacterial DNA was isolated from the oxidation tank of a municipal wastewater treatment plant. Phylogenetic analysis of the 16S rRNA gene sequences cloned from a phage metagenome revealed that bacteriophages transduce genetic material in several major groups of bacteria. The groups identified were as follows: Betaproteobacteria, Gammaproteobacteria, Alphaproteobacteria, Actinomycetales and Firmicutes. Analysis of the 16S rRNA gene sequences in the total bacterial DNA from the same sample revealed that several bacterial groups found in the oxidation tank were not present in the phage metagenome (e.g. Deltaproteobacteria, Nitrospira, Planctomycetes and many Actinobacteria genera). These results suggest that transduction in a wastewater environment occurs in several bacterial groups; however, not all species are equally involved into this process. The data also showed that a number of distinctive bacterial strains participate in transduction-mediated gene transfer within identified bacterial groupings. Denaturing gradient gel electrophoresis analysis confirmed that profiles of the transduced 16S rRNA gene sequences and those present in the whole microbial community show significant differences.

A Description of the Stationary Wave Pattern of a Marine Craft in Shallow and Intermediate Water Depths

A stationary phase model is used to study supercritical waves generated by high speed ferries. Some general relationships in terms of wave angle, propagation direction, dispersion relationship and depth wavelength relationship are explored and discussed. In particular, it is shown that the wave pattern generated by high speed craft at supercritical speeds depends mainly on the relationship of water depth and ship speed and that the wave patterns are similar in terms of location of crests and troughs for a given depth Froude number. In addition it is found that the far field wave pattern can be described adequately using a single moving point source. The theoretical model compares well with towing tank measurements and full scale data over a range of parameters and hull shapes. The paper also demonstrates that the far field wave pattern at supercritical speeds should be non-dimensionalised by water depth and not hull length unlike it is usually done for subcritical speeds.

The assimilation and chronic effects of sub-lethal concentrations of Endosulfan on condition and spawning in the common mussel Mytilus edulis

The rate of uptake of Endosulfan by Mytilus edulis L. exposed to pesticide concentrations of 0.1, 0.5, and 1.0 mg/l, and its subsequent elution on removal to clean sea water, was investigated. Higher residue levels were recorded for mussels exposed to higher concentrations of the pesticide, but concentration factors were reduced. There was a rapid initial fall in tissue residue levels on transfer to clean sea water due, it is suggested, to elution of Endosulfan adsorbed on particulate matter assimilated in the gut. The spawning period was prolonged at higher concentrations and, at 1.0 mg/l, the onset of spawning was delayed, possibly due to interference with gamonic action. At 0.1 mg/l, the minor protraction of the spawning period may reflect the effect of experimental tank conditions. No seasonal trend was obvious, and there was an exaggeration of the expected fall in condition in mussels exposed to higher concentrations of Endosulfan. In controls, the expected seasonal trend was reduced.

Transmission characteristics of a vaginally-worn UHF radio telemeter

A vaginally-worn temperature telemeter may be used by women to chart their basal body temperature for ovulation detection. The telemeter uses a temperature to pulse width converter to key a Colpitts oscillator which is controlled in frequency by a 418 MHz SAW resonator. The circuit’s tank inductor acts as a compact, multi-turn loop antenna with a radiated power in isolation of around 1 uW. The transmission characteristics of the system are affected by the proximity of the human body, which acts as an electrically-large lossy dielectric. The RF link-budget must allow for the reduction in total emitted power, directional body-induced fading, and polarization effects. The polar power patterns of the telemeter were measured for both isolated and in-situ cases, using horizontal and vertical polarization. The power patterns were numerically integrated to determine relative emitted power, and a reference dipole used to determine the emitted power for the isolated device. In isolation the telemeter radiation is vertically polarized and isotropic in nature. With the telemeter in-situ, total body absorption was found to be over 20 dB, with directional fades of up to 40 dB; there was extensive cross-polarization, with up to 60% of radiated power horizontally polarized. With limited radiated power and directional fading, the operating range for the telemeter is limited to single room operation (less than 10m). The majority of RF radiation is absorbed by the body, but the radiation hazard is negligible due to the low power level of the device. The high level of cross-polarization suggests that either horizontal or vertically polarized base-station antennas may be used.

Time-averaged velocity and turbulence intensity at the initial downstream flow from a six-bladed propeller

The current study investigated the time-averaged velocity and turbulence intensity at the initial downstream flow from a six-bladed ship propeller. The six-bladed propeller provided the rapid periodical pulses of thrust in one revolution due to the blades leading to a complex downstream jet. The six-bladed propeller is popular as a boat racing propeller, but the presentation of its flow structure was rarely found in the previous studies. In this study, the experiments were carried out in a water tank to measure the time-averaged velocity and turbulence intensity by using a Laser Doppler Anemometry (LDA) system. The jet was produced by rotating the propeller at a constant speed powered by an electric motor. The maximum tangential and radial velocities of the six-bladed propeller were of 76% and 17% of the maximum axial velocity respectively. The study found that the six-bladed propeller has a lower tangential velocity, but a higher radial velocity with its own diffusing mechanism when comparing to the three-bladed propeller.

The colonization of macroalgal rafts by the genus Idotea (sub-phylum Crustacea; Order Isopoda):An active or passive process?

The association of invertebrate communities with macroalgae rafts has received much attention over recent decades, yet significant gaps in our knowledge remain with respect to the colonization process. Using laboratory-based experiments and in situ field trials in Strangford Lough, Northern Ireland, this study investigated whether members of the known rafting genus Idotea (sub-phylum Crustacea; order Isopoda) could effectively colonize rafts after shore seaweed detachment, or if their presence merely reflected a passive marooning process. Test tank arenas were used to identify traits that may influence the rafting potential of the dominant shore species Idotea granulosa and the well known rafter Idotea baltica. When released mid-water, I. granulosa initially ascended and associated with floating seaweed whereas I. baltica tended to descend with no clear habitat association. These findings conflict with the differential distribution of these Idotea species among rafts and shore algae, thus highlighting the complex nature of the potential of organisms to raft. In the field we considered the relative ability of different Idotea species to colonize tethered rafts composed of Ascophyllum nodosum and Fucus vesiculosus, cleaned of all vagile organisms and deployed at locations adjacent to established intertidal Idotea species populations. At the end of the experiment (after 44 days) rafts were inhabited by known rafting and shoreline species, confirming that colonization can occur after algal detachment. Previously considered shoreline species on occasion outnumbered well known rafters suggesting that a wide range of Idotea species can readily avail of macroalgal rafts as a potential dispersal mechanism or alternative habitat. © 2012 Marine Biological Association of the United Kingdom.

How much gas can we get from grass?

Grass biomethane has been shown to be a sustainable gaseous transport biofuel, with a good energy balance, and significant potential for economic viability. Of issue for the designer is the variation in characteristics of the grass depending on location of source, time of cut and species. Further confusion arises from the biomethane potential tests (BMP) which have a tendency to give varying results. This paper has dual ambitions. One of these is to highlight the various results for biomethane potential that may be obtained from the same grass silage. The results indicated that methane potential from the same grass silage varied from 350 to 493 L CH4 kg−1 VS added for three different BMP procedures. The second ambition is to attempt to compare two distinct digestion systems again using the same grass: a two stage continuously stirred tank reactor (CSTR); and a sequentially fed leach bed reactor connected to an upflow anaerobic sludge blanket (SLBR–UASB). The two engineered systems were designed, fabricated, commissioned and operated at small pilot scale until stable optimal operating conditions were reached. The CSTR system achieved 451 L CH4 kg−1 VS added over a 50 day retention period. The SLBR–UASB achieved 341 L CH4 kg−1 VS added at a 30 day retention time.

Research activities in the MaRINET project: keeping the European marine energy development facilities at world class level

The MaRINET project aims to build a synergy in the European marine renewable energy development infrastructure network, involving a total of 28 partners across the union. Its scope extends from small to large scale testing, in both tank and field. The main activities of the project are to standardize test procedures, to provide centralized free access for European technology developers, and to innovate for improving test infrastructures and techniques.
This paper presents the work carried in this last part, which focuses on research objectives identified to be current challenges for industrial development. They are distributed in 6 topics. On the one hand are issues that concern directly one of the 3 types of energy scoped in the project: wave, tidal, and offshore wind energy. Two examples are the real time estimation of incident waves, and the measurement of turbulence in tidal flows. On the other hand, collaborative effort is drawn on aspects that are common to those technologies: electrical components, environmental monitoring, and dedicated moorings.

Update on Research Activities in the MaRINET Project

The MaRINET FP7 project aims to build a synergy in the European marine renewable energy development infrastructure network, involving a total of 28 partners across the union. Its scope extends from small to large scale testing, in both tank and field. The main activities of the project are to standardize test procedures, to provide centralized free access for European technology developers, and to innovate for improving test infrastructures and techniques.
Two years to the end of the project, this paper presents an update of the work being carried in this last part. It focuses on research objectives identified to be current challenges for industrial development. They are distributed in 6 topics. On the one hand are issues directly related to one of the 3 types of energy scoped in the project: wave, tidal, and offshore wind. On the other hand, collaborative effort is drawn on aspects that are common to those technologies: electrical components, environmental monitoring, and dedicated moorings.
Theory and validation of new test techniques are presented, for example in the case of non-intrusive wave measurements. This is done in coordination with extensive experimental analysis of the phenomena implying tests, such as nonlinearities in moorings.

Chemometric techniques in multivariate statistical modelling of process plant

The techniques of principal component analysis (PCA) and partial least squares (PLS) are introduced from the point of view of providing a multivariate statistical method for modelling process plants. The advantages and limitations of PCA and PLS are discussed from the perspective of the type of data and problems that might be encountered in this application area. These concepts are exemplified by two case studies dealing first with data from a continuous stirred tank reactor (CSTR) simulation and second a literature source describing a low-density polyethylene (LDPE) reactor simulation.

Screw conveyor device for laboratory tests on conditioned soil for EPB tunneling operations

Earth pressure balanced (EPB) full face tunneling machines have experienced a remarkable increase in the number of applications throughout the world due to both mechanical developments and a more effective use of additives to condition the ground. Conditioning modifies the mechanical and hydraulic properties of a soil by making it suitable for the pressure control in the bulk chamber and extraction with the screw conveyor. The extraction system plays a fundamental role during the EPB operations particularly for a correct application of the face pressure. Despite the extensive use of the EPB technique, little knowledge exists concerning the understanding of the behavior of conditioned soil, particularly for noncohesive ground (sand and gravel). This paper presents and describes a prototype laboratory device, which simulates the extraction of the ground from a pressurized tank with a screw conveyor. The results of a preliminary test program carried out on a medium sized sand show that the prototype device is efficient in verifying the effects of foam for an optimal use in EPB conditioning. © 2007 ASCE.