Solubilization of an ionic liquid, 1-butyl-3-methylimidazolium hexafluorophosphate, in a surfactant-water system

The amphiphilic association structures were determined in the system; water, Laureth 4 (approximately C-12(EO)(4)), and the ionic liquid 1-butyl-3-methylimidazolium hexafluorophosphate ([bmim][PF6]), using visual observation and small angle x-ray diffraction. The system showed a lamellar liquid crystal solubilizing the ionic liquid ([bmim][PF6]) to a maximum of 15%, an isotropic surfactant solution dissolving the ionic liquid to a maximum of 39%, an isotropic ionic liquid solution with less than 0.5% of water and surfactant and finally, an aqueous solution with only traces of surfactant and ionic liquid. The small angle x-ray diffraction results showed the ionic liquid to be solubilized into the lamellar liquid crystal without changing the dimensions of the amphiphile layer or the interlayer spacing dependence on the water content.

Solvation of 1-butyl-3-methylimidazolium hexafluorophosphate in aqueous ethanol - a green solution for dissolving 'hydrophobic' ionic liquids

The relatively hydrophobic ionic liquid 1-butyl-3-methylimidazolium hexafluorophosphate has been found to be totally miscible with aqueous ethanol between 0.5 and 0.9 mol fraction ethanol, whereas the ionic liquid is only partially miscible with either pure water or absolute ethanol; the ability to dissolve 1-butyl-3-methylimidazolium hexafluorophosphate in a 'green' aqueous solvent system has important implications for cleaning, purification, and separations using ionic liquids.

Ionic liquids are not always green: hydrolysis of 1-butyl-3-methylimidazolium hexafluorophosphate

1-Butyl-3-methylimidazolium fluoride hydrate has been identified crystallographically as a decomposition product created during purification of the hydrophobic ionic liquid 1-butyl-3-methylimidazolium hexafluorophosphate. This highlights the need to treat ionic liquids much as one would any other research chemical with potentially hazardous properties, unknown toxicity and/or stability, particularly when searching for 'green solvents'.

Adsorption of Ni(SO4) on Malaysian rubber-wood ash

The possible use of wood ash as an adsorbent of nickel sulphate from dilute solutions and the effect of operating parameters were investigated in this study. The rate constants of adsorption were determined at different concentrations and temperatures. The applicability of the first-order reversible equation and an empirical kinetic model were tested to understand the kinetics of nickel sulphate removal at different concentrations. Pore diffusion was found as the rate-controlling step. The Langmuir and Freundlich isotherms were applied to find out the adsorption parameters. The activation energy of adsorption was -11.54 kJ mol-1. The value of the enthalpy change was ?H=-10.35 kcal mol-1.

The electrochemical oxidation of catechol and dopamine on platinum in 1-Ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ([C(2)mim][NTf2]) and 1-Butyl-3-methylimidazolium tetrafluoroborate ([C(4)mim][BF4]): Adsorption effects in ionic liquid voltammetry

The electrochemical oxidation of catechol and dopamine has been studied at a platinum micro-electrode (10 pm diameter) in two room temperature ionic liquids (RTILs): 1-Ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ([C(2)mim][NTf2]) and 1-Butyl-3-methylimidazolium tetrafluoroborate ([C(4)mim][BE4]). For catechol in [C(2)mim][NTf2], an electrochemically quasi-reversible oxidation peak was observed at 1.1 V vs. Pt with a back peak at 0.4 V vs. Pt. This is assigned to the two-electron oxidation of catechol to doubly protonated o-benzoquinone. Double-step chronoamperometry gave a diffusion coefficient for the catechol and the oxidised species which is 3.8 x 10(-11) m(2) s(-1) for both. For catechol in [C(4)mim][BF4], a two-electron oxidation wave was observed at 1.0 V vs. Pt with no back peak. Another peak at less positive potential was also observed at 0.6 V vs. Pt in [C(4)mim][BF4] but not in [C(2)mim][NTf2] which is assigned to the adsorption of electrochemically formed neutral o-benzoquinone on the platinum electrode. The oxidised protonated o-benzoquinone is suggested to be deprotonated by the [BF4](-) anion, but not by the [NTf2](-) anion: hence adsorption of the neutral species at the platinum electrode, not the charged species. For dopamine in both RTILs, two chemically irreversible oxidation peaks were observed at 0.75 V and 1.1 V vs. Pt, and assigned to the oxidation of dopamine to the corresponding semi-quinone and the quinone. Potential-step chronoamperometry was carried out on the oxidation waves of dopamine in [C(2)mim][NTf2] and the diffusion coefficient of species in solution was calculated to be 6.85 x 10(-12) m(2) s(-1) and confirmed that the waves corresponded to one and two electron processes. A third wave was observed at 1.8 V vs. Pt which is attributed to the oxidation of the amine group to a radical cation with likely subsequent follow up chemistry. In [C(4)mim][BF4] a peak at less positive potential was observed for dopamine, similar to catechol which is assigned to the adsorption of the neutral quinone species on the platinum electrode formed by the reaction of the removal of protons from the oxidised dopamine with the [BF4](-) anion. (C) 2009 Elsevier B.V. All rights reserved.

Influence of the anion on the electrical conductivity and glass formation of 1-butyl-3-methylimidazolium ionic liquids

Six ionic liquids based on the 1-butyl-3-methylimidazolium cation have been studied. As anions Cl-, Br-, I-, [NCS](-), [N(CN)(2)](-), and [BF4](-) were selected. The electrical conductivities were determined between 173 and 393 K based on impedance measurements in the frequency range from 0.1 to 10(7) Hz. The electrical conductivity increases, whereas the glass transition temperature, the fragility, and the low temperature activation energy decrease with increasing anion size. The results can be understood from the changing anion-cation interaction strength with changing anion size and from the energy landscape interpretation of the glass transition dynamics. (C) 2010 American Institute of Physics. [doi:10.1063/1.3455892]

Low-pressure solubilities and thermodynamics of solvation of eight gases in 1-butyl-3-methylimidazolium hexafluorophosphate

Experimental values for the solubility of carbon dioxide, ethane, methane, oxygen, nitrogen, hydrogen, argon and carbon monoxide in 1-butyl-3-methylimidazolium hexafluorophosphate, [bmim][PF6] - a room temperature ionic liquid - are reported as a function of temperature between 283 and 343 K and at pressures close to atmospheric. Carbon dioxide is the most soluble and hydrogen is the least soluble of the gases studied with mole fraction solubilities of the order of 10-2 and 10-4, respectively. All the mole fraction solubilities decrease with temperature except for hydrogen for which a maximum is observed at temperatures close to 310 K. From the variation of solubility, expressed as Henry's law constants, with temperature, the partial molar thermodynamic functions of solvation such as the standard Gibbs energy, the enthalpy, and the entropy are calculated. The precision of the experimental data, considered as the average absolute deviation of the Henry's law constants from appropriate smoothing equations, is better than ±1%. © 2005 Elsevier B.V. All rights reserved.

Solubility of carbon dioxide, ethane, methane, oxygen, nitrogen, hydrogen, argon, and carbon monoxide in 1-butyl-3-methylimidazolium tetrafluoroborate between temperatures 283 K and 343 K and at pressures close to atmospheric

Experimental values for the solubility of carbon dioxide, ethane, methane, oxygen, nitrogen, hydrogen, argon and carbon monoxide in 1-butyl-3- methylimidazolium tetrafluoroborate, [bmim][BF4] - a room temperature ionic liquid - are reported as a function of temperature between 283 K and 343 K and at pressures close to atmospheric. Carbon dioxide is the most soluble gas with mole fraction solubilities of the order of 10-2. Ethane and methane are one order of magnitude more soluble than the other five gases that have mole fraction solubilities of the order of 10-4. Hydrogen is the less soluble of the gaseous solutes studied. From the variation of solubility, expressed as Henry's law constants, with temperature, the partial molar thermodynamic functions of solvation such as the standard Gibbs energy, the enthalpy, and the entropy are calculated. The precision of the experimental data, considered as the average absolute deviation of the Henry's law constants from appropriate smoothing equations is of 1%. © 2005 Elsevier Ltd. All rights reserved.

Clarification of rubber mill wastewater by a plant based biopolymer- comparison with common inorganic coagulants

Background: In this study, the efficiency of Guar gum as a biopolymer has been compared with two other widely used inorganic coagulants, ferric chloride (FeCl3) and aluminum chloride (AlCl3), for the treatment of effluent collected from the rubber-washing tanks of a rubber concentrate factory. Settling velocity distribution curves were plotted to demonstrate the flocculating effect of FeCl3, AlCl3 and Guar gum. FeCl3 and AlCl3 displayed better turbidity removal than Guar gum at all settling velocities.

Result: FeCl3, AlCl3 and Guar gum removed 92.8%, 88.2% and 88.1% turbidity, respectively, of raw wastewater at a settling velocity of 0.1 cm min-1, respectively. Scanning electron microscopic (SEM) study conducted on the flocs revealed that Guar gum and FeCl3produced strong intercoiled honeycomb patterned floc structure capable of entrapping suspended particulate matter. Statistical experimental design Response Surface Methodology (RSM) was used to design all experiments, where the type and dosage of flocculant, pH and mixing speed were taken as control factors and, an optimum operational setting was proposed.

Conclusion: Due to biodegradability issues, the use of Guar gum as a flocculating agent for wastewater treatment in industry is highly recommended.

The ageing behaviour of hydrogenated nitrile butadiene rubber/nanoclay nanocomposites in various mediums

Hydrogenated nitrile butadiene rubber (HNBR) nanocomposites were prepared using commercially available organoclays (Cloisite 15A). The main focus of the current investigation is to study the influence of the organoclay reinforced in HNBR after subjecting it to long-term oxidative ageing and immersion studies. All the different nanoclay nanocomposites were air aged for a period of 168 h and at 150°C. The changes in the mechanical properties such as tensile strength and elongation at break have been compared with respect to the control sample. For immersion tests, three different liquid mediums were considered for this current investigation. All the samples were immersed in different mediums for a period of 168 h at 150°C. The changes in the swelling index and the mechanical properties have been reported with respect to the control sample. After reinforcing nanoclays into HNBR there was good resistance to swelling in all the three different liquid mediums in comparison to control sample. Tensile testing was performed on the immersed nanocomposites to evaluate the mechanical behaviour after immersion studies. A probable mechanism behind the improved performance has been suggested. © The Author(s) 2012.

Influence of nanoclays on mechanical and barrier properties of hydrogenated acrylonitrile butadiene rubber nanocomposites

In this research, two different methods have been investigated for optimising the preparation of hydrogenated acrylonitrile butadiene rubber/clay nanocomposites. Commercially available organoclay (Cloisite 20A) has been considered for the preparation of rubber nanocomposites. A detailed analysis has been made to investigate the morphological structure and mechanical behaviour at room temperature and at elevated temperature. Also the influence of organoclays on permeability has been studied. Structural analysis indicates very good dispersion for a low loading of 5 parts per hundred (phr) amount of nanoclays. Significant improvements in mechanical properties have been observed with the addition of organoclays at both room and elevated temperatures. Even with the low level of addition of nanoclays, there was a remarkable reduction in permeability. © Institute of Materials, Minerals and Mining 2011.

Design of an automated solar concentrator for the pyrolysis of scrap rubber

An automated solar reactor system was designed and built to carry out catalytic pyrolysis of scrap rubber tires at 550°C. To maximize solar energy concentration, a two degrees-of-freedom automated sun tracking system was developed and implemented. Both the azimuth and zenith angles were controlled via feedback from six photo-resistors positioned on a Fresnel lens. The pyrolysis of rubber tires was tested with the presence of two types of acidic catalysts, H-beta and H-USY. Additionally, a photoactive TiO<inf>2</inf> catalyst was used and the products were compared in terms of gas yields and composition. The catalysts were characterized by BET analysis and the pyrolysis gases and liquids were analyzed using GC-MS. The oil and gas yields were relatively high with the highest gas yield reaching 32.8% with H-beta catalyst while TiO<inf>2</inf> gave the same results as thermal pyrolysis without any catalyst. In the presence of zeolites, the dominant gasoline-like components in the gas were propene and cyclobutene. The TiO<inf>2</inf> and non-catalytic experiments produced a gas containing gasoline-like products of mainly isoprene (76.4% and 88.4% respectively). As for the liquids they were composed of numerous components spread over a wide distribution of C<inf>10</inf> to C<inf>29</inf> hydrocarbons of naphthalene and cyclohexane/ene derivatives.

Control of wild rubber extraction in the forests of northeast India, 1850-1880

This paper uses the history of rubber extraction to explore competing attempts to control the forest environments of Assam and beyond in the second half of the nineteenth century. Forest communities faced rival efforts at environmental control from both European and Indian traders, as well as from various centres of authority within the Raj. Government attempts to regulate rubber collection were undermined by the weak authority of the Raj in these regions, leading to widespread smuggling. Partly in response to the disruptive influence of rubber traders on the frontier, the Raj began to restrict the presence of outsiders in tribal regions, which came to be understood as distinct areas outside British control. When rubber yields from the forests nearest the Brahmaputra fell in the wake of intensive exploitation, India's scientific foresters demanded and from 1870 obtained the ability to regulate the Assamese forests, blaming indigenous rubber tapping strategies for the declining yields and arguing that Indian rubber could be ‘equal [to] if not better' than Amazonian rubber if only tappers would change their practices. The knowledge of the scientific foresters was fundamentally flawed, however, and their efforts to establish a new type of tapping practice failed. By 1880, the government had largely abandoned attempts to regulate wild Indian rubber, though wild sources continued to dominate the supply of global rubber until after 1910.