Phenol degradation by powdered metal ion modified titanium dioxide photocatalysts

Conventional water purification and disinfection generally involve potentially hazardous substances, some of which known to be carcinogenic in nature. Titanium dioxide photocatalytic processes provide an effective route to destroy hazardous organic contaminants. This present work explores the possibility of the removal of organic pollutants (phenol) by the application of TiO2 based photocatalysts. The production of series of metal ions doped or undoped TiO2 were carried out via a sol–gel method and a wet impregnation method. Undoped TiO2 and Cu doped TiO2 showed considerable phenol degradation. The efficiency of photocatalytic reaction largely depends on the photocatalysts and the methods of preparation the photocatalysts. The doping of Fe, Mn, and humic acid at 1.0 M% via sol–gel methods were detrimental for phenol degradation. The inhibitory effect of initial phenol concentration on initial phenol degradation rate reveals that photocatalytic decomposition of phenol follows pseudo zero order reaction kinetics. A concentration of > 1 g/L TiO2 and Cu doped TiO2 is required for the effective degradation of 50 mg/L of phenol at neutral pH. The rise in OH- at a higher pH values provides more hydroxyl radicals which are beneficial of phenol degradation. However, the competition among phenoxide ion, Cl- and OH- for the limited number of reactive sites on TiO2 will be a negative influence in the generation of hydroxyl radical. The dependence of phenol degradation rate on the light intensity was observed, which also implies that direct sunlight can be a substitute for the UV lamps and that photocatalytic treatment of organic pollutants using this technique shows some promise.

Metal levels in the bones and livers of globally threatened marbled teal and white-headed duck from El Hondo, Spain

El Hondo is a key area for marbled teal and white-headed duck. We present Pb, Cu, Zn, Se, and As data for bone and liver in birds found dead between 1996 and 2001. Several metals were higher in adult white-headed ducks than in marbled teal. They were higher in female than in male white-headed ducks, and did not differ with sex in marbled teal, but did by age. Lead in liver of adults was influenced by Pb shot ingestion, which was detected in 21% of marbled teal and in 71% of white-headed duck. No marbled teal had liver levels indicative of Pb poisoning, while 86% of white-headed ducks did. Selenium, Zn, and Cu were elevated in 13%, 7%, and 39% of birds, respectively. Whilst Pb shot poses the greatest threat to these species, further work should assess exposure via plants, invertebrates, water, and sediments for other metals, and investigate possible sub-lethal effects.

‘5 ways to say your prayers’:The Art and Architecture of Curating People, Place and Creativity in a Post-Conflict Context. The Shed, Galway, Ireland 18th June – 23rd July 2013 Includes: 1. Co-Curation of Exhibition with Peter Mutschler, Director of PS² and 2. Morrow’s individual work as part of the exhibition, entitled ‘Departures & Arrivals: Academic Interactions with the Activities, Artists and Archive of PS² ’

This exhibition profiles the curatorial approach of PS² and the work of creative practitioners who have practiced alongside and with the organisation. PS² is a Belfast-based, voluntary arts organisation that initiates projects inside and outside its project space. It seeks to develop a socio-spatial practice that responds to the post-conflict context of Northern Ireland, with particular focus on active intervention and social interaction between local people, creative practitioners, multidisciplinary groups and theorists.
Morrow has collaborated with PS² since its inception in 2005, acting as curatorial advisor specifically on the projects that occur outside PS² . She regards her involvement as a parallel action to her pedagogical explorations within architectural education.

Morrow's personal contribution to the Exhibition aimed to:
-interrogate PS² spatial projects
-contextualise PS² curatorial practice
-open up the analytical framework and extend to similar local practices

The Shed, Galway, Ireland is a joint Galway City Arts and Harbour Company venture. The exhibition subsequently travelled to DarcSpace Gallery, Dublin (Sept 2013).

In Situ Formation of Micron-Scale Li-Metal Anodes with High Cyclability

Scanning probe microscopy methods have been used to electrodeposit and cycle micron-scale Li anodes deposited electrochemically under nanofabricated Au current collectors. An average Li volume of 5 x 10(8) nm(3) was deposited and cycled with 100% coulombic efficiency for similar to 160 cycles. Integrated charge/discharge values agree with before/after topography, as well as in situ dilatometry, suggesting this is a reliable method to study solid-state electrochemical processes. In this work we illustrate the possibility to deposit highly cyclable nanometer thick Li electrodes by mature SPM and nanofab techniques which can pave the way for inexpensive nanoscale battery arrays. 

The Outcomes of Cross-Cultural Adjustment: A Case of British Expatriates Working on International Architectural, Engineering and Construction Assignments

The main aim of this study is to investigate the consequences of cross-cultural adjustment in an under researched sample of British expatriates working on International Architectural, Engineering and Construction (AEC) assignments. Adjustment is the primary outcome of an expatriate assignment. According to Bhaskar-Srinivas et al., (2005), Harrison et al., (2004) it is viewed to affect other work related outcomes which could eventually predict expatriate success. To address the scarcity of literature on expatriate management in the AEC sector, an exploratory design was adopted. Phase one is characterised by extensive review of extant literature, whereas phase two was qualitative exploration from British expatriates’ perspective; here seven unstructured interviews were carried out. Further, cognitive mapping analysis through Banaxia decision explorer software was conducted to develop a theoretical framework and propose various hypotheses. The findings imply that British AEC firms could sustain their already established competitive advantage in the global marketplace by acknowledging the complexity of international assignments, prioritising expatriate management and offering a well-rounded support to facilitate expatriate adjustment and ultimately achieve critical outcomes like performance, assignment completion and job satisfaction.

The outcomes of cross-cultural adjustment: A case of British expatriates working on international architectural, engineering and construction assignments

The main aim of this study is to investigate the consequences of cross-cultural adjustment in an under researched sample of British expatriates working on International Architectural, Engineering and Construction (AEC) assignments. Adjustment is the primary outcome of an expatriate assignment. According to Bhaskar-Srinivas et al., (2005), Harrison et al., (2004) it is viewed to affect other work related outcomes which could eventually predict expatriate success. To address the scarcity of literature on expatriate management in the AEC sector, an exploratory design was adopted. Phase one is characterised by extensive review of extant literature, whereas phase two was qualitative exploration from British expatriatesÕ perspective; here seven unstructured interviews were carried out. Further, cognitive mapping analysis through Banaxia decision explorer software was conducted to develop a theoretical framework and propose various hypotheses. The findings imply that British AEC firms could sustain their already established competitive advantage in the global marketplace by acknowledging the complexity of international assignments, prioritising expatriate management and offering a well-rounded support to facilitate expatriate adjustment and ultimately achieve critical outcomes like performance, assignment completion and job satisfaction.

Almost nothing, almost anywhere: the metal shed in Ireland

This paper argues that the modern barn in Ireland is a complex social and architectural phenomena that is without, or has yet to find, a satisfactory discourse. Emerging in the middle third of the twentieth century, the modern barn – replete with corrugated iron and I-sections – continues to represent a presence in the Irish landscape whose ubiquity is as emphatic as its flexibility. It is, however, its universal properties that begin to suggest connections with wider narratives. The modernising aspects of the barn that appear in the 1920s and 30s begin to conflate with a rhetoric of architectural modernism which was simultaneously appearing across Europe. But while the relationship between high modernism’s critique of what it divined as the inspirational qualities of utilitarian buildings – Walter Gropius on grain silos, Le Corbusier on aircraft hangers etc. – has been well-documented, in Ireland this relationship perhaps contains another layer of complexity.
The barn’s consolidation as a modern type coincided with the search for a nation’s cultural identity after centuries of colonial rule. This tended to be an introspective vision that prioritised rural space over urban space, agriculture over industry, and imagined the small farm as a central tenet in the construction of a new State. This paper suggests that the twentieth-century barn – as a product of the mechanisation of agriculture promoted by the new administrations – is an iconic structure, emblematic of attempts to reconcile the contradictory forces and imagery of modernity with the mores of a traditional society. Moreover, given a cultural purview that was often ambivalent or even hostile to the ideologies and forms of modernity, the barn in Ireland is, perhaps, not so much the inspiration but the realisation of an architectural modernism in that country at its most pervasive, enduring and unself-conscious.

The use of carbon and gold electrodes in anodic stripping voltammetric heavy metal sensors.

The use of anodic stripping voltammetry (ASV)has been proven in the past to be a precise and sensitive analytical method with an excellent limit of detection. Electrochemical sensors could help to avoid expensive and time consuming procedures as sample taking and storage and provide a both sensitive and reliable method for the direct monitoring of heavy metals in the aquatic environment. Solid electrodes which have been used in this work, were produced using previously developed methods. Commercially available and newly designed, screen printed carbon and gold plated working electrodes (WE) were compared. Good results were achieved with the screen printed and plated electrodes under conditions optimized for each electrode material. The electrode stability, reproducibility of single measurements and the limit of detection obtained for Pb were satisfactory (3*10-6mol/l on screen printed carbon WEs after 60 s of deposition and 6*10-6 mol/l on gold plated WEs after 5 min of deposition). Complete 3-electrode-sets (counter, reference and working electrode) were screen printed on different substrates (glass, polycarbonate and alumina). Also here, both carbon and gold were used as WE. Using 3-electrode-sets with a gold plated WE on glass was a limit of detection of 7*10-7 mol/l was achieved after only 60 s of deposition.

Stable Isolated Metal Atoms as Active Sites for Photocatalytic Hydrogen Evolution

The process of using solar energy to split water to produce hydrogen assisted by an inorganic semiconductor is crucial for solving our energy crisis and environmental problems in the future. However, most semiconductor photocatalysts would not exhibit excellent photocatalytic activity without loading suitable co-catalysts. Generally, the noble metals have been widely applied as co-catalysts, but always agglomerate during the loading process or photocatalytic reaction. Therefore, the utilization efficiency of the noble co-catalysts is still very low on a per metal atom basis if no obvious size effect exists, because heterogeneous catalytic reactions occur on the surface active atoms. Here, for the first time, we have synthesized isolated metal atoms (Pt, Pd, Rh, or Ru) stably by anchoring on TiO2, a model photocatalystic system, by a facile one-step method. The isolated metal atom based photocatalysts show excellent stability for H-2 evolution and can lead to a 6-13-fold increase in photocatalytic activity over the metal clusters loaded on TiO2 by the traditional method. Furthermore, the configurations of isolated atoms as well as the originality of their unusual stability were analyzed by a collaborative work from both experiments and theoretical calculations.

Oxygen Reduction Reaction on Metal-Terminated MnCr2O4 Nano-octahedron Catalyzing MnS Dissolution in an Austenitic Stainless Steel

To understand pitting corrosion in stainless steel is very important, and a recent work showed that the MnS dissolution catalyzed by MnCr2O4{111} is a starting point of pit g. This demonstrates the need to understand the oxygen reduction reaction (ORR) on MnCr2O4{111}, which is the other half-reaction to complete pitting corrosion. In this study, the adsorption behaviors of all oxygen-containing species on MnCr2O4{111}, which has several possible terminations, are explored via density functional theory calculations. It is found that O-2 adsorbs on MnCr2O4{111) surfaces very strongly. Many possible reactions are investigated and the favored reaction mechanism of ORR is determined. The interactions between O-2 and H2O on the two metal-terminated MriCr(2)O(4){111} are found to be different according to the atomic configurations of the two surfaces. All the calculated results suggest that ORR can readily occur on the MnCr2O4{111} surfaces.

A DFT study of the transition metal promotion effect on ethylene chemisorption on Co(0001)

Transition metals are often introduced to a catalyst as promoters to improve catalytic performance. In this work, we study the promotion effect of transition metals on Co, the preferred catalytic metal for Fischer-Tropsch synthesis because of its good compromise of activity, selectivity and stability, for ethylene chemisorption using density functional theory (DFT) calculations, aiming to provide some insight into improving the alpha-olefin selectivity. In order to obtain the general trend of influence on ethylene chemisorption, twelve transition metals (Zr, Mn, Re, Ru, Rh, It, Ni, Pd, Pt, Cu, Ag and Au) are calculated. We find that the late transition metals (e.g. Pd and Cu) can decrease ethylene chemisorption energy. These results suggest that the addition of the late transition metals may improve alpha-olefin selectivity. Electronic structure analyses (both charge density distributions and density of states) are also performed and the understanding of calculated results is presented. (C) 2009 Elsevier B.V. All rights reserved.

Early Implementation of BIM into a Cold-Formed Steel Design/ Fabricator and an Architectural/Planning Consultancy

There is a broad consensus surrounding the ability of building information modelling (BIM) to positively impact a project by enabling greater collaboration. This paper aims to examine the development of BIM and how it can contribute to the evermore present and growing cold-formed steel (CFS) industry. This is achieved thorough a comprehensive literature review and four exploratory interviews with industry experts. Work has been carried out, for the first time, alongside one of the UK’s largest CFS Designer/Fabricators in conjunction with Northern Ireland’s leading Architectural and Town Planning Consultants in the identification and dissemination of information. The capabilities of BIM have been investigated through modeling of simple CFS structures n consultation with the project partners. By scrutinising the literature and associated interviews, the primary opportunities, as well as barriers, of BIM implementation have been investigated in the context of these companies. It is essential to develop greater understanding of the flexibility, adaptability and interoperability of BIM software as the UK construction industry faces a daunting challenge; fully collaborative 3D BIM as required by the UK Government under the “Government Construction Strategy” by 2016 in all public sector projects. This paper, and the wider study that it stems from, approaches the problem from a new angle, from sections of the construction industry that have not yet fully embedded BIM.

Advances in single-shot, dry drilling of composite/metal stacks

Carbon fibre reinforced polymers (CFRP) are increasingly being used in the aerospace, automotive and defence industry due to their high specific stiffness and good corrosion resistance. In a modern aircraft, 50-60% of its structure is made up of CFRP material while the remainder is mostly a combination of metallic alloys (typically aluminium or titanium alloys). Mechanical fastening (bolting or riveting) of CFRP and metallic components has thus created a pressing requirement of drilling several thousand holes per aircraft. Drilling of stacks in a single-shot not only saves time, but also ensures proper alignment when fasteners are inserted, achieving tighter geometric tolerances. However, this requirement poses formidable manufacturing challenges due to the fundamental differences in the material properties of CFRP and metals e.g. a drill bit entering into the stack encounters brittle and abrasive CFRP material as well as the plastic behaviour of the metallic alloy, making the drilling process highly non-linear.

Over the past few years substantial efforts have been made in this direction and majority of the research has tried to establish links between how the process parameters (feed, depth of cut, cutting speed), tooling (geometry, material and coating) and the wear of the cutting tool affect the hole quality. Similarly, multitudes of investigations have been conducted to determine the effects of non-traditional drilling methods (orbital, helical and vibration assisted drilling), cutting zone temperatures and efficiency of chip extraction on the hole quality and rate of tool wear during single shot drilling of CFRP/alloy stacks.

In a timely effort, this paper aims at reviewing the manufacturing challenges and barriers faced when drilling CFRP/alloy stacks and to summarise various factors influencing the drilling process while detailing the advances made in this fertile research area of single-shot drilling of stack materials. A survey of the key challenges associated with avoiding workpiece damage and the effect these challenges have on tool design and process optimisation is presented. An in depth critique of suitable hole making methods and their aptness for commercialisation follows. The paper concludes by summarising the future work required to achieve repeatable, high quality single shot drilled holes in CFRP/alloy stacks.