Element-Free Galerkin Modelling of Crack Migration in Composite Laminates

The development of a virtual testing environment, as a cost-effective industrial design tool in the design and analysis of composite structures, requires the need to create models efficiently, as well as accelerate the analysis by reducing the number of degrees of freedom, while still satisfying the need for accurately tracking the evolution of a debond, delamination or crack front. The eventual aim is to simulate both damage initiation and propagation in components with realistic geometrical features, where crack propagation paths are not trivial. Meshless approaches, and the Element-Free Galerkin (EFG) method, are particularly suitable for problems involving changes in topology and have been successfully applied to simulate damage in homogeneous materials and concrete. In this work, the method is utilized to model initiation and mixed-mode propagation of cracks in composite laminates, and to simulate experimentally-observed crack migration which is difficult to model using standard finite element analysis. N

Finite-element investigation of cold-formed steel portal frames in fire

This paper presents the results of a full-scale site fire test performed on a cold-formed steel portal frame building with semi-rigid joints. The purpose of the study is to establish a performance-based approach for the design of such structures in fire boundary conditions. In the full-scale site fire test, the building collapsed asymmetrically at a temperature of 714°C. A non-linear elasto-plastic finite-element shell model is described and is validated against the results of the full-scale test. A parametric study is presented that highlights the importance of in-plane restraint from the side rails in preventing an outwards sway failure for both a single portal and full building geometry model. The study also demonstrates that the semi-rigidity of the joints should be taken into account in the design. The single portal and full building geometry models display a close match to site test results with failure at 682°C and 704°C, respectively. A design case is described in accordance with Steel Construction Institute design recommendations. The validated single portal model is tested with pinned bases, columns protected, realistic loading and rafters subject to symmetric uniform heating in accordance with the ISO 834 standard fire curve; failure occurs at 703°C.

Signal Reliability Improvement Using Selection Combining Based Macro-Diversity for Off-Body Communications At 868 MHz

This paper investigates the potential improvement in signal reliability for outdoor short-range off-body communications channels at 868 MHz using the macro-diversity offered by multiple co-located base stations. In this study, ten identical hypothetical base stations were positioned equidistantly around the perimeter of a rectangle of length 6.67 m and width 3.3 m. A body worn node was placed on the central chest region of an adult male. Five scenarios, each considering different user trajectories, were then analyzed to test the efficacy of using macro-diversity when the desired link is subject to shadowing caused by the human body. A number of selection combining based macro-diversity configurations consisting of four and then ten base stations were considered. It was found that using a macro-diversity system consisting of four base stations (or equivalently signal branches), a maximum diversity gain of 22.5 dB could be obtained while implementing a 10-base station setup this figure could be improved to 25.2 dB.

Finite element modelling of cyclic behaviour of cold-formed steel bolted moment-resisting connections

This paper investigates the accuracy of new finite element modelling approaches to predict the behaviour of bolted moment-connections between cold-formed steel members, formed by using brackets bolted to the webs of the section, under low cycle fatigue. ABAQUS software is used as a modelling platform. Such joints are used for portal frames and potentially have good seismic resisting capabilities, which is important for construction in developing countries. The modelling implications of a two-dimensional beam element model, a three-dimensional shell element model and a three-dimensional solid element model are reported. Quantitative and qualitative results indicate that the three-dimensional quadratic S8R shell element model most accurately predicts the hysteretic behaviour and energy dissipation capacity of the connection when compared to the test results.

Photoionization cross sections for the trans-iron element Se + from 18 to 31 eV

Absolute photoionization cross-section calculations are presented for Se + using large-scale close-coupling calculations within the Breit--Pauli and Dirac--Coulomb R -matrix approximations. The results from our theoretical work are compared with recent measurements (Esteves 2010 PhD Thesis publication number AAI3404727, University of Reno, NV, USA; Sterling et al 2011 J. Phys. B: At. Mol. Opt. Phys. 44 025701; Esteves et al 2011 Phys. Rev. A 84 013406) made at the advanced light source (ALS) radiation facility in Berkeley, CA, USA. We report on results for the photon energy range 18.0--31.0 eV, which spans the ionization thresholds of the 4 S o 3/2 ground state and the low-lying 2 D o 5/2,3/2 and 2 P o 3/2,1/2 metastable states. Metastable fractions are inferred from our present work. Resonance energies and quantum defects of the prominent Rydberg resonances series identified in the spectra are compared for the 4p → n d transitions with the recent ALS experimental measurements made on this complex trans-iron element.

Linking Family Engagement with a Rights Perspective: Macro Factors Influencing Practice

While child welfare practitioners in many countries are struggling to develop methods of effective family engagement, they operate within different national and cultural contexts which influence, both positively and negatively, the ability to engage with families. Increasingly, international comparisons are necessary to further understanding of the development of social work practice. This is particularly necessary because most countries utilize international frameworks (such as the United National Convention on the Rights of the Child) to provide guidance in the development of policies, programs, and interventions. Each country (and locality) struggles to advance practice to be more effective and humane. Our paper offers a comparative analysis focused on family-oriented and rights-based frameworks of different countries. Based on a review of current national policies and a review of the literature regarding family based practices, we examine similarities and differences among four countries: the United Kingdom, Sweden, the United States, and South Korea. These countries were selected because they have some similarities (advanced industrialized democracies, professional social work, formal child protection systems) but have some differences in their social welfare systems (policies, specific practices, socio-cultural context). These differences can be utilized to advance understanding regarding the promise and potential for family engagement strategies. We then discuss the utility of this comparison for theory-building in the arena of child care practice and conclude by identifying the challenges and limitations of this work.