Multilayered glass fibre-reinforced composites in rotational moulding

The potential of multiple layer fibre-reinforced mouldings is of growing interest to the rotational moulding industry because of their cost/performance ratio. The particular problem that arises when using reinforcements in this process relate to the fact that the process is low shear and good mixing of resin and reinforcement is not optimum under those conditions. There is also a problem of the larger/heavier reinforcing agents segregating out of the powder to lay up on the inner part surface. In this study, short glass fibres were incorporated and distributed into a polymer matrix to produce fibre-reinforced polymer composites using the rotational moulding process and characterised in terms of morphology and mechanical properties. © 2011 American Institute of Physics.

Mechanical properties of polyamide 6 reinforced microfibrilar composites

The mechanical behavior of microfibrilar composites (MFC), consisting of a matrix of high-density polyethylene (HDPE) and reinforcement of polyamide 6 (PA6) fibrils, with and without compatibilization, was studied. The composites were produced by conventional processing techniques with various shape and arrangement of the PA6 reinforcing entities: long, unidirectional, or crossed bundles of fibrils (UDP and CPC, respectively), middle-length, randomly oriented bristles (MRB), or non-oriented micrometric PA6 spheres (NOM). The tensile, flexural, and impact properties of the MFC materials (UDP, CPC, and MRB) were determined as a function of the PA6 reinforcement shape, alignment and content, and compared with those of NOM, the non-fibrous composite. It was concluded that the in-situ MFC materials based on HDPE/PA6 blends display improvements in the mechanical behavior when compared with the neat HDPE matrix, e.g., up to 33% for the Young modulus, up to 119% for the ultimate tensile strength, and up to 80% for the flexural stiffness. Copyright © 2011 Society of Plastics Engineers.

Development of Novel Post-Tensioned Glulam Timber Composites

Improvements in the structural performance of glulam timber beams by the inclusion of reinforcing materials can increase both the service performance and ultimate capacity. In recent years research focusing on the addition of fibre reinforced polymers (FRP) to strengthen members has yielded positive results. However, the FRP material is still relatively expensive and its full potential in combination with structural timber has not been realised. This paper describes a series of four-point bending tests that were conducted, under service loads and to failure, on unreinforced, reinforced and post-tensioned glulam timber beams, where the reinforcing tendon used was 12mm diameter basalt fibre reinforced polymer (BFRP). The research was designed to evaluate the benefits offered by including an active reinforcement in contrast to the passive reinforcement typically used within timber strengthening works, in addition to establishing the affect that bonding the reinforcing tendon has on the material’s performance. Further experimental tests have been developed to investigate the long-term implications of this research, with emphasis placed upon creep and loss of post-tensioning.
The laboratory investigations established that the flexural strength and stiffness increased for both the unbonded and bonded post-tensioned timbers compared to the unreinforced beams. Timber that was post-tensioned with an unbonded BFRP tendon showed a flexural strength increase of 2.8% and an increase in stiffness of 8.7%. Post-tensioned beams with a bonded BFRP tendon showed increases in flexural strength and stiffness of 16.6% and 11.5% respectively.

Effects of particle/matrix interface and strengthening mechanisms on the mechanical properties of metal matrix composites

A randomly distributed multi-particle model considering the effects of particle/matrix interface and strengthening mechanisms introduced by the particles has been constructed. Particle shape, distribution, volume fraction and the particles/matrix interface due to the factors including element diffusion were considered in the model. The effects of strengthening mechanisms, caused by the introduction of particles on the mechanical properties of the composites, including grain refinement strengthening, dislocation strengthening and Orowan strengthening, are incorporated. In the model, the particles are assumed to have spheroidal shape, with uniform distribution of the centre, long axis length and inclination angle. The axis ratio follows a right half-normal distribution. Using Monte Carlo method, the location and shape parameters of the spheroids are randomly selected. The particle volume fraction is calculated using the area ratio of the spheroids. Then, the effects of particle/matrix interface and strengthening mechanism on the distribution of Mises stress and equivalent strain and the flow behaviour for the composites are discussed.

Preparation and surface modification of submicron YAl2 particles by mixed milling with magnesium for fabricating YAl2p/MgLiAl composites

A new process for the preparation and surface modification of submicron YAl2 intermetallic particles was proposed to control the agglomeration of ultrafine YAl2 particles and interface in the fabrication of YAl2p/MgLiAl composites. The morphological and structural evolution during mechanical milling of YAl2 powders (< 30 μm) with magnesium particles (~ 100 μm) has been characterized by scanning electron microscopy, transmission electron microscopy, and X-ray diffraction. The results show that YAl2 particles are refined to submicron scale and separately cladded in magnesium coatings after mixed milling with magnesium particles for 20 h. Mechanical and metallurgical bonds have been found in YAl2/Mg interfaces without any interface reactions. Both the refining and mechanical activation efficiencies for YAl2 particles are enhanced, which may be related to the addition of magnesium particles leading to atomic solid solution and playing a role as “dispersion stabilizer”.

An analysis of the attitudes of dental patients attending general dental practice in Galway

AIM: To describe the patterns of dental attendance and attitudes towards tooth loss of general dental practice patients in Galway.

OBJECTIVES: 1. To determine the pattern of adult dental attendance in general practices in Galway; and, 2. To examine the oral health attitudes of these patients.

METHOD: Questionnaires were distributed to 311 consecutive adult patients in the waiting rooms of ten general dental practices in Galway, which were randomly selected from the telephone directory.

RESULTS: A total of 254 of the 311 questionnaires distributed were fully completed, returned and included in the results, giving a response rate of 81.7%. A total of 59% of dentate participants attended their dentist for annual or biannual examinations compared to 23% of edentate patients. Some 10.5% of medical card holders and 0.5% of non-medical card holders were edentulous.

CONCLUSIONS: The data from the survey indicated that medical card holders in Galway were more likely to be edentulous than nonmedical card holders. Edentate patients were less likely to be regular dental attenders than dentate patients.

Is the shortened dental arch an underused treatment strategy in the Republic of Ireland?

OBJECTIVES: To determine the proportion of Republic of Ireland 35-44 and 65+ year-olds currently satisfying the criteria for a classic shortened dental arch (SDA) of 20 anterior teeth.

RESEARCH DESIGN: Secondary analysis of data collected in the 2000/02 epidemiological survey of the oral health of Irish adults.

CLINICAL SETTING: Participants underwent a clinical oral examination in health board dental clinics and completed a detailed interview pertaining to dental and general health.

PARTICIPANTS: The analysis is based on a random sample of adults, aged 35 to 44 years (n = 978), and 65 years and older (n = 714).

MAIN OUTCOME MEASURES: The SDA was measured as 20 teeth in the mouth in the positions normally described as from the left second premolar to the right second premolar in each arch.

RESULTS: Only one of the 35-44 year-olds and none of the 65+ year-olds had teeth in their mouths in positions normally described as a classic SDA. However, of the 35-44 year old age group only five patients who had at least a premolar dentition of 20 contiguous teeth had been provided with a removable denture compared to one patient from the 65+ years group.

CONCLUSIONS: Very few older patients in the Republic of Ireland have a SDA based on the measure used. However, very few have been provided with removable dentures where they already possess at least a premolar dentition of 20 contiguous teeth. Suggested reasons for this may include limitations of the data recorded, patient preferences and economic factors.

Do removable dental prosthesis have an impact on tooth loss?

DESIGN: A multi-centre randomised controlled study in 14 dental schools. This report is an interim analysis at 3 years.

INTERVENTION: Patients were allocated to either the Removable dental prosthesis group (RPD)-109 patients or the no prosthesis group (SDA) -106 patients. Patients had to be older than 35 years with no molars in the study jaw. Follow-up visits were scheduled at 4 to 8 wks (baseline), at 6 months, and at 1, 2, 3, 4, and 5 yrs after treatment.

OUTCOME MEASURE: Time to loss of first tooth following intervention or no intervention.

RESULTS: 81 patients received a RDP and 69 patients received no treatment in the end. This is a reduction of 26% and 35% respectively from the time when they were randomised to the two groups. Tooth loss occurred in 13 of the RDP group (16% of those who received the RDP, 12% of those allocated to the group at the start) with 5 of these being in the study jaw and 8 in the opposing jaw. Tooth loss occurred in 9 of the SDA group (13% of those who received SDA, 9% of those who were allocated to the group at the start) with 5 in the study jaw and 4 in the opposing jaw. The respective Kaplan-Meier survival rates at 38 months were 0.83 (95% CI: 0.74-0.91) in the RDP group and 0.86 (95% CI: 0.78-0.95) in the SDA group.

CONCLUSIONS: The difference in tooth loss at three years between patients treated with RDP and those not treated with RDP was not significant.