Optimisation and scaling of interfacial GeO2 layers for high-k gate stacks on germanium and extraction of dielectric constant of GeO2

Germanium is an attractive channel material for MOSFETs because of its higher mobility than silicon. In this paper, GeO2 has been investigated as an interfacial layer for high-kappa gate stacks on germanium. Thermally grown GeO2 layers have been prepared at 550 degrees C to minimise GeO volatilisation. GeO2 growth has been performed in both pure O-2 ambient and O-2 diluted with N-2. GeO2 thickness has been scaled down to approximately 3 nm. MOS capacitors have been fabricated using different GeO2 thicknesses with a standard high-kappa dielectric on top. Electrical properties and thermal stability have been tested up to at least 350 degrees C. The K value of GeO2 was experimentally determined to be 4.5. Interface state densities (D-it) of less than 10(12) CM-2 eV(-1) have been extracted for all devices using the conductance method.

The size and shape of shells used by hermit crabs: A multivariate analysis of Clibanarius erythropus

Shell attributes Such as weight and shape affect the reproduction, growth, predator avoidance and behaviour of several hermit crab species. Although the importance of these attributes has been extensively investigated, it is still difficult to assess the relative role of size and shape. Multivariate techniques allow concise and efficient quantitative analysis of these multidimensional properties, and this paper aims to understand their role in determining patterns of hermit crab shell use. To this end, a multivariate approach based on a combination of size-unconstrained (shape) PCA and RDA ordination was used to model the biometrics of southern Mediterranean Clibanarius erythropus Populations and their shells. Patterns of shell utilization and morphological gradients demonstrate that size is more important than shape, probably due to the limited availability of empty shells in the environment. The shape (e.g. the degree of shell elongation) and weight of inhabited shells vary considerably in both female and male crabs. However, these variations are clearly accounted for by crab biometrics in males only. Oil the basis of statistical evidence and findings from past studies. it is hypothesized that larger males of adequate size and strength have access to the larger, heavier and relatively more available shells of the globose Osilinus turbinatus, which cannot be used by average-sized males or by females investing energy in egg production. This greater availability allows larger males to select more Suitable Shapes. (C) 2009 Elsevier Masson SAS. All rights reserved.

A calming cacophony: Social identity can shape the experience of loud noise

Environmental Psychology has typically considered noise as pollution and focused upon its negative impact. However, recent research in psychology and anthropology indicates the experience of noise as aversive depends upon the meanings with which it is attributed. Moreover, such meanings seem to be dependent on the social context. Here we extend this research through studying the aural experience of a religious festival in North India which is characterised by loud, continuous and cacophonous noise. Reporting an experiment and semi-structured interviews, we show that loud noise is experienced as pleasant or unpleasant according to the meanings attributed to it. Specifically, the experiment shows the same noise is experienced more positively (and listened to longer) when attributed to the festival rather than to a non-festival source. In turn, the qualitative data show that within the Mela, noises judged as having a religious quality are reported as more positive than noises that are not. Moreover, the qualitative data suggest a key factor in the evaluation of noise is our participants’ social identities as pilgrims. This identity provides a framework for interpreting the auditory environment and noises judged as intruding into their religious experience were judged negatively, whereas noises judged as contributing to their religious experience were judged more positively. Our findings therefore point to the ways in which our social identities are implicated in the process of attributing meaning to the auditory environment.

Effect of post-weld heat-treatment on the oxide film and corrosion behaviour of laser-welded shape memory NiTi wires

Post-weld heat-treatment (PWHT) was applied to NiTi weldments to improve the corrosion behaviour by modifying the microstructure and surface composition. The surface oxide film on the weldments is principally TiO2, together with some Ti, TiO, and Ti2O3. The surface Ti/Ni ratio of the weldments after PWHT is increased. The oxide film formed in Hanks’ solution is thicker on the weldments after PWHT. The pitting resistance of the weldments is increased by PWHT. The galvanic effect in the weldments is very small. The weldment with PWHT at 350 °C shows the best corrosion resistance among other heat-treated weldments in this study.

Effect of postweld heat treatment on the microstructure and cyclic deformation behavior of laser-welded NiTi-shape memory wires

NiTi wires of 0.5 mm diameter were laser welded using a CW 100-W fiber laser in an argon shielding environment with or without postweld heat-treatment (PWHT). The microstructure and the phases present were studied by scanning-electron microscopy (SEM), transmission-electron microscopy (TEM), and X-ray diffractometry (XRD). The phase transformation behavior and the cyclic stress–strain behavior of the NiTi weldments were studied using differential scanning calorimetry (DSC) and cyclic tensile testing. TEM and XRD analyses reveal the presence of Ni4Ti3 particles after PWHT at or above 623 K (350 °C). In the cyclic tensile test, PWHT at 623 K (350 °C) improves the cyclic deformation behavior of the weldment by reducing the accumulated residual strain, whereas PWHT at 723 K (450 °C) provides no benefit to the cyclic deformation behavior. Welding also reduces the tensile strength and fracture elongation of NiTi wires, but the deterioration could be alleviated by PWHT.

Effects of process parameters upon the shape memory and pseudo-elastic behaviors of laser-welded NiTi thin foil

This article discusses the effects of laser welding parameters such as power, welding speed, and focus position on the weld bead profile, microstructure, pseudo-elasticity (PE), and shape memory effect (SME) of NiTi foil with thickness of 250 um using 100W CW fiber laser. The parameter settings to produce the NiTi welds for analysis in this article were chosen from a fractional factorial design to ensure the welds produced were free of any apparent defect. The welds obtained were mainly of cellular dendrites with grain sizes ranging from 2.5 to 4.8 um at the weld centerline. A small amount of Ni3Ti was found in the welds. The onset of transformation temperatures (As and Ms) of the NiTi welds shifted to the negative side as compared to the as-received NiTi alloy. Ultimate tensile stress of the NiTi welds was comparable to the as received NiTi alloy, but a little reduction in the pseudo-elastic property was noted. Full penetration welds with desirable weld bead profiles and mechanical properties were successfully obtained in this study.

Laser welding of thin foil nickel–titanium shape memory alloy

In this study, two L27 Taguchi experiments were carried out to study the effect of fibre laser welding parameters and their interactions upon the weld bead aspect ratio of nickel–titanium thin foil. The optimum parameters to produce full penetrated weld with the largest aspect ratio and desirable microstructure were successfully obtained by the Taguchi experimental design. The corrosion property of the optimized NiTi weld in Hank’s solution at 37.5 °C was studied and compared with the as-received NiTi. To improve the corrosion properties of the weld, the effect of post-weld-heat-treatments ranging from 573 to 1173 K was investigated. The corrosion properties, surface morphology, microstructure and Ti/Ni ratio of the heat-treated NiTi weld were analysed. It was found that a post-weld heat treatment at 573 K for 1 h provided the best pitting corrosion resistance at the weld zone.

Reduction of environmentally induced cracking of laser-welded shape memory NiTi wires via post-weld heat-treatment

In this study, the environmentally induced cracking behaviour of the NiTi weldment with and without post-weld heat-treatment (PWHT) in Hanks’ solution at 37.5 °C at OCP were studied by tensile and cyclic slow-strain-rate tests (SSRT), and compared with those tested in oil (an inert environment). Our previous results in the tensile and cyclic SSRT showed that the weldment without PWHT showed high susceptibility to the hydrogen cracking, as evidenced by the degradation of tensile and super-elastic properties when testing in Hanks' solution. The weldment after PWHT was much less susceptible to hydrogen attack in Hanks' solution as no obvious degradation in the tensile and super-elastic properties was observed, and only a very small amount of micro-cracks were found in the fracture surface. The susceptibility to hydrogen cracking of the NiTi weldment could be alleviated by applying PWHT at the optimized temperature of 350 °C after laser welding.

Changing shape and shifting boundaries - the media portrayal of probation in Ireland

Literature on the media representation of probation highlights that probation as a ‘brand’ and concept is poorly understood and lacks public visibility. This has implications for its legitimacy and credibility. In this article we explore probation’s visibility in one country, the Republic of Ireland, through a critical analysis of print media representations of probationover a 12-year period (2001 to 2012). While our study finds that the majority of the coverage of probation was either positive or neutral in tone, we note a recent shift towards a more negative tone that we argue is reflective of the changing shape of the penal-probation boundaries. These changes are linked to resourcing of the criminal justice system and have implications for the public perception of probation.