Optimising the locations of thermally sensitive equipment in an aircraft crown compartment

A Design of Experiments (DoE) analysis was undertaken to generate a list of configurations for CFD numerical simulation of an aircraft crown compartment. Fitted regression models were built to predict the convective heat transfer coefficients of thermally sensitive dissipating elements located inside this compartment. These are namely the SEPDC and the Route G. Currently they are positioned close to the fuselage and it is of interest to optimise the heat transfer for reliability and performance purposes. Their locations and the external fuselage surface temperature were selected as input variables for the DoE. The models fit the CFD data with values ranging from 0.878 to 0.978, and predict that the optimum locations in terms of heat transfer are when the elements are positioned as close to the crown floor as possible ( and ?min. limits), where they come in direct contact with the air flow from the cabin ventilation system, and when they are positioned close to the centreline ( and ?CL). The methodology employed allows aircraft thermal designers to optimise equipment placement in confined areas of an aircraft during the design phase. The determined models should be incorporated into global aircraft numerical models to improve accuracy and reduce model size and computational time. © 2012 Elsevier Masson SAS. All rights reserved.

Efficient Non-Linear Idealisations of Aircraft Fuselage Panels in Compression

Aircraft fuselages are complex assemblies of thousands of components and as a result simulation models are highly idealised. In the typical design process, a coarse FE model is used to determine loads within the structure. The size of the model and number of load cases necessitates that only linear static behaviour is considered. This paper reports on the development of a modelling approach to increase the accuracy of the global model, accounting for variations in stiffness due to non-linear structural behaviour. The strategy is based on representing a fuselage sub-section with a single non-linear element. Large portions of fuselage structure are represented by connecting these non-linear elements together to form a framework. The non-linear models are very efficient, reducing computational time significantly

Influence of Manufacturing Tolerance on Aircraft Direct Operating Cost (DOC)

The influence of manufacturing tolerance on direct operating cost (DOC) is extrapolated from an engine nacelle to be representative of an entire aircraft body. Initial manufacturing tolerance data was obtained from the shop floor at Bombardier Aerospace Shorts, Belfast while the corresponding costs were calculated according to various recurring elements such as basic labour and overtime labour, rework, concessions, and redeployment; along with the non-recurrent costs due to tooling and machinery, etc. The relation of tolerance to cost was modelled statistically so that the cost impact of tolerance change could be ascertained. It was shown that a relatively small relaxation in the assembly and fabrication tolerances of the wetted surfaces resulted in reduced costs of production that lowered aircraft DOC, as the incurred drag penalty was predicted and taken into account during the optimisation process.

Parametric optimisation of manufacturing tolerances at the aircraft surface

Up until now, aircraft surface smoothness requirements have been aerodynamically driven with tighter manufacturing tolerance to minimize drag, that is, the tighter the tolerance, the higher is the assembly cost in the process of manufacture. In the current status of commercial transport aircraft operation, it can be seen that the unit cost contributes to the aircraft direct operating cost considerably more than the contribution made by the cost of block fuel consumed for the mission profile. The need for a customer-driven design strategy to reduce direct operating cost by reducing aircraft cost through manufacturing tolerance relaxation at the wetted surface without unduly penalizing parasite drag is investigated. To investigate this, a preliminary study has been conducted at 11 key manufacturing features on the surface assembly of an isolated nacelle. In spite of differences in parts design and manufacture, the investigated areas associated with the assembly of nacelles are typical of generic patterns in the assembly of other components of aircraft. The study is to be followed up by similar studies extended to lifting surfaces and fuselage

Integrating Aircraft Cost Modelling into Conceptual Design

The article presents cost modeling results from the application of the Genetic-Causal cost modeling principle. Industrial results from redesign are also presented to verify the opportunity for early concept cost optimization by using Genetic-Causal cost drivers to guide the conceptual design process for structural assemblies. The acquisition cost is considered through the modeling of the recurring unit cost and non-recurring design cost. The operational cost is modeled relative to acquisition cost and fuel burn for predominately metal or composites designs. The main contribution of this study is the application of the Genetic-Causal principle to the modeling of cost, helping to understand how conceptual design parameters impact on cost, and linking that to customer requirements and life cycle cost.