Design of Transparent Conducting Electrodes and Surface Relief Gratings for Plasmonic Polymer Solar Cells

As the concept of renewable energy becomes increasingly important in the modern society, a considerable amount of research has been conducted in the field of organic photovoltaics in recent years. Although organic solar cells generally have had lower efficiencies compared to silicon solar cells, they have the potential to be mass produced via solution processing. A common polymer solar cell architecture relies on the usage of P3HT (electron donor) and PCBM (electron acceptor) bulk heterojunction. One of the main issues with this configuration is that in order to compensate for the high exciton recombination rate, the photoactive layer is often made very thin (on the order of 100 $%). This results in low solar cell photocurrents due to low absorption. This thesis investigates a novel method of light trapping by coupling surface plasmons at the electrode interface via surface relief gratings, leading to EM field enhancements and increased photo absorption. Experimental work was first conducted on developing and optimizing a transparent electrode of the form &'()/+,/&'() to replace the traditional ITO electrode since the azopolymer gratings cannot withstand the high temperature processing of ITO films. It was determined that given the right thickness profiles and deposition conditions, the MAM stack can achieve transmittance and conductivity similar to ITO films. Experimental work was also conducted on the fabrication and characterization of surface relief gratings, as well as verification of the surface plasmon generation. Surface relief gratings were fabricated easily and accurately via laser interference lithography on photosensitive azopolymer films. Laser diffraction studies confirmed the grating pitch, which is dependent on the incident angle and wavelength of the writing beam. AFM experiments were conducted to determine the surface morphology of the gratings, before and after metallic film deposition. It was concluded that metallic film deposition does not significantly alter the grating morphologies.

Design of Transparent Conducting Electrodes and Surface Relief Gratings for Plasmonic Polymer Solar Cells

As the concept of renewable energy becomes increasingly important in the modern society, a considerable amount of research has been conducted in the field of organic photovoltaics in recent years. Although organic solar cells generally have had lower efficiencies compared to silicon solar cells, they have the potential to be mass produced via solution processing. A common polymer solar cell architecture relies on the usage of P3HT (electron donor) and PCBM (electron acceptor) bulk heterojunction. One of the main issues with this configuration is that in order to compensate for the high exciton recombination rate, the photoactive layer is often made very thin (on the order of 100 $%). This results in low solar cell photocurrents due to low absorption. This thesis investigates a novel method of light trapping by coupling surface plasmons at the electrode interface via surface relief gratings, leading to EM field enhancements and increased photo absorption. Experimental work was first conducted on developing and optimizing a transparent electrode of the form &'()/+,/&'() to replace the traditional ITO electrode since the azopolymer gratings cannot withstand the high temperature processing of ITO films. It was determined that given the right thickness profiles and deposition conditions, the MAM stack can achieve transmittance and conductivity similar to ITO films. Experimental work was also conducted on the fabrication and characterization of surface relief gratings, as well as verification of the surface plasmon generation. Surface relief gratings were fabricated easily and accurately via laser interference lithography on photosensitive azopolymer films. Laser diffraction studies confirmed the grating pitch, which is dependent on the incident angle and wavelength of the writing beam. AFM experiments were conducted to determine the surface morphology of the gratings, before and after metallic film deposition. It was concluded that metallic film deposition does not significantly alter the grating morphologies.

Surface wave and storm surge prediction during Hurricane Sandy

Hurricane Sandy was the largest storm on historical record in the Atlantic Ocean basin with extensive coastal damage caused by large waves and high storm surge. The primary objectives of this thesis are to compare and evaluate three different spatially-varying surface wind fields of Hurricane Sandy to investigate the impact of the differences between the complex wind fields on predictions of the sea surface evolution, and to evaluate the impact of the storm on the hydrodynamics in Great South Bay (GSB) and the discharge of ocean water into the back-barrier bay from overwash over Fire Island. Three different spatially-varying surface wind fields were evaluated and compared to wind observations, including the parametric Holland (1980) model (H80), the parametric Generalized Asymmetric Holland Model (GAHM), and results from the WeatherFlow Regional Atmospheric Modelling System (WRAMS). The winds were used to drive the coupled Delft3D-SWAN hydrodynamic and ocean wave models on a regional grid. The results indicate that the WRAMS wind field produces wave model predictions in the best agreement with significant wave height observations, followed by the GAHM and H80 wind fields and that a regional atmospheric wind model is best for hindcasting hurricane waves and water levels when detailed observations are available, while a parametric vortex model is best for forecasting hurricane sea surface conditions. Using a series of four connected Delft3D-SWAN grids to achieve finer resolution over Fire Island and GSB, a higher resolution WRAMS was used to predict waves and storm surge. The results indicate that strong local winds have the largest influence on water level fluctuations in GSB. Three numerical solutions were conducted with varying extents of barrier island overwash. The simulations allowing for minor and major overwash indicated good agreement with observations in the east end of GSB and suggest that island overwash provided a significant contribution of ocean water to GSB during the storm. Limiting the overwash in the numerical model directly impacts the total discharge into GSB from the ocean through existing inlets. The results of this study indicate that barrier island overwash had a significant impact on the water levels in eastern GSB.