The Evolution of the Los Negritos Porphyry Copper Deposit, Coquimbo, Chile: Geological, Geochronological, Mineralogical and Geochemical Evidence

The Los Negritos porphyry copper deposit is located ~ 4 km to the northeast of Carmen de Andacollo Mine in the Chilean Cretaceous metallogenic belt. The mineralization is hosted in andesite of the Quebrada Marquesa Formation and a series of at least four early to intramineral porphyry intrusive rock types: plagioclase quartz biotite porphyry (P1b and P1a dated at 109.60± 0.75 Ma and 107.22± 0.40 Ma); plagioclase biotite porphyry (P2: 106.30 ± 0.47 Ma); and quartz plagioclase biotite porphyry (P3: 106.19 ± 0.42 Ma). These units are cut by late‐ to post‐mineral plagioclase‐hornblende porphyritic rocks (P4b: 106.20 ± 0.69 Ma and P4a: 106.50 ± 0.68 Ma). The earliest intrusive units (P1) were affected by an initial stage of K‐feldspar‐biotite alteration, with chalcopyrite, molybdenite (date at 108.5 ± 0.5 Ma) and gold (up to 0.11 ppm), and the surrounding volcanic host rock was overprinted by chlorite‐epidote dominated (propylitic) alteration. Subsequent to the P2 and P3 intrusion, these rocks were affected by albite and then a second stage of potassic alteration. The Ti and Ba contents in hydrothermal biotite are notably lower (typically Ti = 0.100‐0.144 a.p.f.u. and Ba = 0.001‐0.005 a.p.f.u) than in magmatic ones (generally Ti = 0.186‐0.222 a.p.f.u. and Ba = 0.014‐0.023 a.p.f.u.), and constitute an excellent discriminant of the nature of biotite. These early stages of alteration were overprinted by copper‐molybdenum bearing chlorite‐sericite alteration at 106.60 ± 0.5 Ma (Re‐Os age in molybdenite) and by quartz‐sericite‐pyrite veins (phyllic), respectively in the southwest and northeast areas. The average temperature associated with these two alteration facies is estimated around 305 °C. Weak albite‐calcite alteration, spatially associated with sulfosalts and distributed along the margins of P3, overprinted the phyllic facies. The intrusive rock units at the Los Negritos and Carmen de Andacollo deposits are geochemically classified as diorite to granodiorite with a calc‐alkaline magmatic affinity, and formed in a volcanic arc setting from partial melting of a metasomatized mantle wedge. They are interpreted to be cogenetic, and related to a common long‐lived magma chamber that emplaced during a period of tectonic inversion known as the Subhercynian, Peruvian or Pacific event.

Simulating Granite Emplacement and Deformation with Centrifuge Analogue Modelling

The Greater Himalayan leucogranites are a discontinuous suite of intrusions emplaced in a thickened crust during the Miocene southward ductile extrusion of the Himalayan metamorphic core. Melt-induced weakening is thought to have played a critical role in strain localization that facilitated the extrusion. Recent advancements in centrifuge analogue modelling techniques allow for the replication of a broader range of crustal deformation behaviors, enhancing our understanding of large hot orogens. Polydimethylsiloxane (PDMS) is commonly used in centrifuge experiments to model weak melt zones. Difficulties in handling PDMS had, until now, limited its emplacement in models prior to any deformation. A new modelling technique has been developed where PDMS is emplaced into models that have been subjected to some shortening. This technique aims to better understand the effects of melt on strain localization and potential decoupling between structural levels within an evolving orogenic system. Models are subjected to an early stage of shortening, followed by the introduction of PDMS, and then a final stage of shortening. Theoretical percentages of partial melt and their effect on rock strength are considered when adding a specific percentage of PDMS in each model. Due to the limited size of the models, only PDMS sheets of 3 mm thickness were used, which varied in length and width. Within undeformed packages, minimal surface and internal deformation occurred when PDMS is emplaced in the lower layer of the model, showing a vertical volume increase of ~20% within the package; whereas the emplacement of PDMS into the middle layer showed internal dragging of the middle laminations into the lower layer and a vertical volume increase ~30%. Emplacement of PDMS results in ~7% shortening for undeformed and deformed models. Deformed models undergo ~20% additional shortening after two rounds of deformation. Strain localization and decoupling between units occur in deformed models where the degree of deformation changes based on the amount of partial melt present. Surface deformation visible by the formation of a bulge, mode 1 extension cracks and varying surface strain ellipses varies depending if PDMS is present. Better control during emplacement is exhibited when PDMS is added into cooler models, resulting in reduced internal deformation within the middle layer.