SIGNIFICANCE OF HEAT DISSIPATION IN THE CATHODE CATALYST LAYER ON THE LIFETIME AND RELIABILITY OF POLYMER ELECTROLYTE FUEL CELLS

To study the dissipation of heat generated due to the formation of pinholes that cause local hotspots in the catalyst layer of the Polymer Electrolyte Fuel Cell, a two-phase non-isothermal model has been developed by coupling Darcy’s law with heat transport. The domain under consideration is a section of the membrane electrode assembly with a half-channel and a half-rib. Five potential locations where a pinhole might form were analyzed: at the midplane of the channel, midway between the channel midplane and the channel wall, at the channel or rib wall, midway between the rib midplane and the channel wall, at the midplane of the rib. In the first part of this work, a preliminary thermal model was developed. The model was then refined to account for the two-phase effects. A sensitivity study was done to evaluate the effect of the following properties on the maximum temperature in the domain: Catalyst layer thermal conductivity, the Microporous layer thermal conductivity, the anisotropy factor of the Catalyst layer thermal conductivity, the Porous transport layer porosity, the liquid water distribution and the thickness of the membrane and porous layers. Accounting for the two-phase effects, a slight cooling effect was observed across all hotspot locations. The thermal properties of the catalyst layer were shown to have a limited impact on the maximum temperature in the catalyst layer of new fuel cells without pinhole. However, as hotspots start to appear, thermal properties play a more significant role in mitigating the thermal runaway.

Proton Formation in 2+1 Resonance Enhanced Multiphoton Excitation of HCl and HBr via „=0… Rydberg and Ion-Pair States

Molecular beam cooled HCl was state selected by two-photon excitation of the V (1) summation operator(0(+)) [v=9,11-13,15], E (1) summation operator(0(+)) [v=0], and g (3) summation operator(-)(0(+)) [v=0] states through either the Q(0) or Q(1) lines of the respective (1,3) summation operator(0(+))<--<--X (1) summation operator(0(+)) transition. Similarly, HBr was excited to the V (1) summation operator(0(+)) [v=m+3, m+5-m+8], E (1) summation operator(0(+)) [v=0], and H (1) summation operator(0(+)) [v=0] states through the Q(0) or Q(1) lines. Following absorption of a third photon, protons were formed by three different mechanisms and detected using velocity map imaging. (1) H(*)(n=2) was formed in coincidence with (2)P(i) halogen atoms and subsequently ionized. For HCl, photodissociation into H(*)(n=2)+Cl((2)P(12)) was dominant over the formation of Cl((2)P(32)) and was attributed to parallel excitation of the repulsive [(2) (2)Pi4llambda] superexcited (Omega=0) states. For HBr, the Br((2)P(32))Br((2)P(12)) ratio decreases with increasing excitation energy. This indicates that both the [(3) (2)Pi(12)5llambda] and the [B (2) summation operator5llambda] superexcited (Omega=0) states contribute to the formation of H(*)(n=2). (2) For selected intermediate states HCl was found to dissociate into the H(+)+Cl(-) ion pair with over 20% relative yield. A mechanism is proposed by which a bound [A (2) summation operatornlsigma] (1) summation operator(0(+)) superexcited state acts as a gateway state to dissociation into the ion pair. (3) For all intermediate states, protons were formed by dissociation of HX(+)[v(+)] following a parallel, DeltaOmega=0, excitation. The quantum yield for the dissociation process was obtained using previously reported photoionization efficiency data and was found to peak at v(+)=6-7 for HCl and v(+)=12 for HBr. This is consistent with excitation of the repulsive A(2) summation operator(12) and (2) (2)Pi states of HCl(+), and the (3) (2)Pi state of HBr(+). Rotational alignment of the Omega=0(+) intermediate states is evident from the angular distribution of the excited H(*)(n=2) photofragments. This effect has been observed previously and was used here to verify the reliability of the measured spatial anisotropy parameters.