ThreeDimensional Epigraphic Recording at Stobi (Former Yugoslav Republic of Macedonia): Creating a Virtual Lapidarium

There is an increased need for 3D recording of archaeological sites and digital preservation of their artifacts. Digital photogrammetry with prosumer DSLR cameras is a suitable tool for recording epigraphy in particular, as it allows for the recording of inscribed surfaces with very high accuracy, often better than 2 mm and with only a short time spent in the field. When photogrammetry is fused with other computational photography techniques like panoramic tours and Reflectance Transformation Imaging, a workflow exists to rival traditional LiDAR­based methods. The difficulty however, arises in the presentation of 3D data. It requires an enormous amount of storage and end­user sophistication. The proposed solution is to use game­engine technology and high definition virtual tours to provide not only scholars, but also the general public with an uncomplicated interface to interact with the detailed 3D epigraphic data. The site of Stobi, located near Gradsko, in the Former Yugoslav Republic of Macedonia (FYROM) was used as a case study to demonstrate the effectiveness of RTI, photogrammetry and virtual tour imaging working in combination. A selection of nine sets of inscriptions from the archaeological site were chosen to demonstrate the range of application for the techniques. The chosen marble, sandstone and breccia inscriptions are representative of the varying levels of deterioration and degradation of the epigraphy at Stobi, in which both their rates of decay and resulting legibility is varied. This selection includes those which are treated and untreated stones as well as those in situ and those in storage. The selection consists of both Latin and Greek inscriptions with content ranging from temple dedication inscriptions to statue dedications. This combination of 3D modeling techniques presents a cost and time efficient solution to both increase the legibility of severely damaged stones and to digitally preserve the current state of the inscriptions.

Process Monitoring and Defect Detection of Additive Manufacturing Using Inline Coherent Imaging

With applications ranging from aerospace to biomedicine, additive manufacturing (AM) has been revolutionizing the manufacturing industry. The ability of additive techniques, such as selective laser melting (SLM), to create fully functional, geometrically complex, and unique parts out of high strength materials is of great interest. Unfortunately, despite numerous advantages afforded by this technology, its widespread adoption is hindered by a lack of on-line, real time feedback control and quality assurance techniques. In this thesis, inline coherent imaging (ICI), a broadband, spatially coherent imaging technique, is used to observe the SLM process in 15 - 45 $\mu m$ 316L stainless steel. Imaging of both single and multilayer builds is performed at a rate of 200 $kHz$, with a resolution of tens of microns, and a high dynamic range rendering it impervious to blinding from the process beam. This allows imaging before, during, and after laser processing to observe changes in the morphology and stability of the melt. Galvanometer-based scanning of the imaging beam relative to the process beam during the creation of single tracks is used to gain a unique perspective of the SLM process that has been so far unobservable by other monitoring techniques. Single track processing is also used to investigate the possibility of a preliminary feedback control parameter based on the process beam power, through imaging with both coaxial and 100 $\mu m$ offset alignment with respect to the process beam. The 100 $\mu m$ offset improved imaging by increasing the number of bright A-lines (i.e. with signal greater than the 10 $dB$ noise floor) by 300\%. The overlap between adjacent tracks in a single layer is imaged to detect characteristic fault signatures. Full multilayer builds are carried out and the resultant ICI images are used to detect defects in the finished part and improve upon the initial design of the build system. Damage to the recoater blade is assessed using powder layer scans acquired during a 3D build. The ability of ICI to monitor SLM processes at such high rates with high resolution offers extraordinary potential for future advances in on-line feedback control of additive manufacturing.

Wind Shear, Gust, and Yaw-Induced Dynamic Stall on Wind-Turbine Blades

This study examined the effect of a spanwise angle of attack gradient on the growth and stability of a dynamic stall vortex in a rotating system. It was found that a spanwise angle of attack gradient induces a corresponding spanwise vorticity gradient, which, in combination with spanwise flow, results in a redistribution of circulation along the blade. Specifically, when modelling the angle of attack gradient experienced by a wind turbine at the 30% span position during a gust event, the spanwise vorticity gradient was aligned such that circulation was transported from areas of high circulation to areas of low circulation, increasing the local dynamic stall vortex growth rate, which corresponds to an increase in the lift coefficient, and a decrease in the local vortex stability at this point. Reversing the relative alignment of the spanwise vorticity gradient and spanwise flow results in circulation transport from areas of low circulation generation to areas of high circulation generation, acting to reduce local circulation and stabilise the vortex. This circulation redistribution behaviour describes a mechanism by which the fluctuating loads on a wind turbine are magnified, which is detrimental to turbine lifetime and performance. Therefore, an understanding of this phenomenon has the potential to facilitate optimised wind turbine design.

The Organizational Tasks of High-Performance Gymnastic Coaches

The purpose of this study was to report the knowledge used by expert high performance gymnastic coaches in the organization of training and competition. In-depth interviews were conducted with 9 coaches who worked with male gymnasts and 8 coaches who worked with female gymnasts. Qualitative analyses showed that coaches of males and coaches of females planned training similarly, except that coaches of females appeared to emphasize esthetic and nutritional issues to a greater extent. Coaches of males revealed more concerns about the organization of gymnasts' physical conditioning. Analysis indicated that expert gymnastic coaches of males and females are constantly involved in dynamic social interactions with gymnasts, parents, and assistant coaches. Many areas of coaches' organizational work, such as dealing with the athletes' personal concerns and working with parents, are not part of the structure of coaches' training programs and emerged as crucial tasks of expert gymnastic coaches for developing elite gymnasts.

BIDIRECTIONAL AC-DC CONVERTERS USING ONE CYCLE CONTROL (OCC) FOR ELECTRIC VEHICLES

The electric vehicle (EV) market has seen a rapid growth in the recent past. With an increase in the number of electric vehicles on road, there is an increase in the number of high capacity battery banks interfacing the grid. The battery bank of an EV, besides being the fuel tank, is also a huge energy storage unit. Presently, it is used only when the vehicle is being driven and remains idle for rest of the time, rendering it underutilized. Whereas on the other hand, there is a need of large energy storage units in the grid to filter out the fluctuations of supply and demand during a day. EVs can help bridge this gap. The EV battery bank can be used to store the excess energy from the grid to vehicle (G2V) or supply stored energy from the vehicle to grid (V2G ), when required. To let power flow happen, in both directions, a bidirectional AC-DC converter is required. This thesis concentrates on the bidirectional AC-DC converters which have a control on power flow in all four quadrants for the application of EV battery interfacing with the grid. This thesis presents a bidirectional interleaved full bridge converter topology. This helps in increasing the power processing and current handling capability of the converter which makes it suitable for the purpose of EVs. Further, the benefit of using the interleaved topology is that it increases the power density of the converter. This ensures optimization of space usage with the same power handling capacity. The proposed interleaved converter consists of two full bridges. The corresponding gate pulses of each switch, in one cell, are phase shifted by 180 degrees from those of the other cell. The proposed converter control is based on the one-cycle controller. To meet the challenge of new requirements of reactive power handling capabilities for grid connected converters, posed by the utilities, the controller is modified to make it suitable to process the reactive power. A fictitious current derived from the grid voltage is introduced in the controller, which controls the converter performance. The current references are generated using the second order generalized integrators (SOGI) and phase locked loop (PLL). A digital implementation of the proposed control ii scheme is developed and implemented using DSP hardware. The simulated and experimental results, based on the converter topology and control technique discussed here, are presented to show the performance of the proposed theory.

Method to Improve the Linearity of Active Commutating Mixers Using Dynamic Current Injection

A double balanced (DBM) CMOS mixer providing high linearity is presented in this paper. A cross-coupled pair used in the IF stage of the mixer to dynamically inject current into the to mixer provide a high linearity. The proposed DBM was fabricated using a standard 130-nm CMOS process and was tested on-wafer. The double balanced mixer delivers 10 dB conversion gain, 9.5 dBm IIP3, and input P1dB of -2.4 dBm. RF bandwidth of the proposed mixer is 6 GHz, covering 0.5 GHz to 6.5 GHz with IF bandwidth of 300 MHz. RF to IF and LO to IF isolation are also better than 59 dB in the whole frequency band. The circuit uses an area of 0.015 mm2 excluding bonding pads and draw 4.5mW from a 1.2V supply.