Stress Inversion Using LiDAR Tunnel Deformation Measurements

Far-field stresses are those present in a volume of rock prior to excavations being created. Estimates of the orientation and magnitude of far-field stresses, often used in mine design, are generally obtained by single-point measurements of stress, or large-scale, regional trends. Point measurements can be a poor representation of far-field stresses as a result of excavation-induced stresses and geological structures. For these reasons, far-field stress estimates can be associated with high levels of uncertainty. The purpose of this thesis is to investigate the practical feasibility, applications, and limitations of calibrating far-field stress estimates through tunnel deformation measurements captured using LiDAR imaging. A method that estimates the orientation and magnitude of excavation-induced principal stress changes through back-analysis of deformation measurements from LiDAR imaged tunnels was developed and tested using synthetic data. If excavation-induced stress change orientations and magnitudes can be accurately estimated, they can be used in the calibration of far-field stress input to numerical models. LiDAR point clouds have been proven to have a number of underground applications, thus it is desired to explore their use in numerical model calibration. The back-analysis method is founded on the superposition of stresses and requires a two-dimensional numerical model of the deforming tunnel. Principal stress changes of known orientation and magnitude are applied to the model to create calibration curves. Estimation can then be performed by minimizing squared differences between the measured tunnel and sets of calibration curve deformations. In addition to the back-analysis estimation method, a procedure consisting of previously existing techniques to measure tunnel deformation using LiDAR imaging was documented. Under ideal conditions, the back-analysis method estimated principal stress change orientations within ±5° and magnitudes within ±2 MPa. Results were comparable for four different tunnel profile shapes. Preliminary testing using plastic deformation, a rough tunnel profile, and profile occlusions suggests that the method can work under more realistic conditions. The results from this thesis set the groundwork for the continued development of a new, inexpensive, and efficient far-field stress estimate calibration method.

ThreeDimensional Epigraphic Recording at Stobi (Former Yugoslav Republic of Macedonia): Creating a Virtual Lapidarium

There is an increased need for 3D recording of archaeological sites and digital preservation of their artifacts. Digital photogrammetry with prosumer DSLR cameras is a suitable tool for recording epigraphy in particular, as it allows for the recording of inscribed surfaces with very high accuracy, often better than 2 mm and with only a short time spent in the field. When photogrammetry is fused with other computational photography techniques like panoramic tours and Reflectance Transformation Imaging, a workflow exists to rival traditional LiDAR­based methods. The difficulty however, arises in the presentation of 3D data. It requires an enormous amount of storage and end­user sophistication. The proposed solution is to use game­engine technology and high definition virtual tours to provide not only scholars, but also the general public with an uncomplicated interface to interact with the detailed 3D epigraphic data. The site of Stobi, located near Gradsko, in the Former Yugoslav Republic of Macedonia (FYROM) was used as a case study to demonstrate the effectiveness of RTI, photogrammetry and virtual tour imaging working in combination. A selection of nine sets of inscriptions from the archaeological site were chosen to demonstrate the range of application for the techniques. The chosen marble, sandstone and breccia inscriptions are representative of the varying levels of deterioration and degradation of the epigraphy at Stobi, in which both their rates of decay and resulting legibility is varied. This selection includes those which are treated and untreated stones as well as those in situ and those in storage. The selection consists of both Latin and Greek inscriptions with content ranging from temple dedication inscriptions to statue dedications. This combination of 3D modeling techniques presents a cost and time efficient solution to both increase the legibility of severely damaged stones and to digitally preserve the current state of the inscriptions.

Examination of body image among Canadian adolescents: Relations with physical activity and screen time

Background: Adolescence is a period of life associated with self-perceptions of negative body image. Physical activity levels are low and screen time levels are also high during this stage. These perceptions and behaviours are associated with poor health outcomes, making research on their determinants important. With adolescent populations, certain groups may be at higher risk of body dissatisfaction than others, and body dissatisfaction may influence individual physical activity and screen time levels. Objectives: The objectives of this thesis were to: 1) describe body image among young Canadians, examining possible health inequalities 2) estimate the strength and significance of associations between body satisfaction, physical activity and screen time, and 3) examine the potential etiological role of biological sex. Methods: Objective 1: The 2013/2014 Health Behaviour in School-aged Children study was employed. Sex-stratified Rao-Scott chi-square analyses were conducted to examine associations between socio-demographic factors and body satisfaction. Objective 2: The 2005/2006 and 2013/2014 cross-sectional and 2006 longitudinal HBSC data sets were used. Sex-stratified modified Poisson regressions were conducted and risk estimates and associated confidence intervals obtained. Results: Objective 1: Among males, being older, of East and Southeast Asian ethnicity, and reporting low SES all were associated with body dissatisfaction. Among females, being older, of Arab and West Asian or African ethnicity, being born in Canada, and reporting low SES were all associated with being body dissatisfied. Objective 2: Cross-sectionally, males who reported ‘too fat’ body dissatisfaction were more likely to be physically inactive. Adolescents of both sexes who reported ‘too fat’ body dissatisfaction were more likely to engage in high levels of screen time. Data from the longitudinal component supported the idea that male ‘too fat’ body dissatisfaction temporally leads to physical inactivity, but showed an inverse relationship between body dissatisfaction and screen time. Conclusions: Objective 1: Future prevention efforts in Canada should target subgroups to effectively help those at greatest risk of body dissatisfaction, and ameliorate potential inequalities at the population level. Objective 2: The presence of these relationships may inform future interventions as part of a multi-factorial etiology, in order to increase physical activity and decrease screen time among youth.

An exploration of students’ perceptions and attitudes towards creativity in engineering education

This study used a mixed methods approach to develop a broad and deep understanding of students’ perceptions towards creativity in engineering education. Studies have shown that students’ attitudes can have an impact on their motivation to engage in creative behavior. Using an ex-post facto independent factorial design, attitudes of value towards creativity, time for creativity, and creativity stereotypes were measured and compared across gender, year of study, engineering discipline, preference for open-ended problem solving, and confidence in creative abilities. Participants were undergraduate engineering students at Queen’s University from all years of study. A qualitative phenomenological methodology was adopted to study students’ understandings and experiences with engineering creativity. Eleven students participated in oneon- one interviews that provided depth and insight into how students experience and define engineering creativity, and the survey included open-ended items developed using the 10 Maxims of Creativity in Education as a guiding framework. The findings from the survey suggested that students had high value for creativity, however students in fourth year or higher had less value than those in other years. Those with preference for open-ended problem solving and high confidence valued creative more than their counterparts. Students who preferred open-ended problem solving and students with high confidence reported that time was less of a hindrance to their creativity. Males identified more with creativity stereotypes than females, however overall they were both low. Open-ended survey and interview results indicated that students felt they experienced creativity in engineering design activities. Engineering creativity definitions had two elements: creative action and creative characteristic. Creative actions were associated with designing, and creative characteristics were predominantly associated with novelty. Other barriers that emerged from the qualitative analysis were lack of opportunity, lack of assessment, and discomfort with creativity. It was concluded that a universal definition is required to establish clear and aligned understandings of engineering creativity. Instructors may want to consider demonstrating value by assessing creativity and establishing clear criteria in design projects. It is recommended that students be given more opportunities for practice through design activities and that they be introduced to design and creative thinking concepts early in their engineering education.

Differential contributions of the mIPS and PMd in the movement planning of reaches investigated through HD-tDCS

To reach for a target, we must formulate a movement plan - a difference vector of the target position with respect to the starting hand position. While it is known that the medial part of the intraparietal sulcus (mIPS) and the dorsal premotor (PMd) activity reflects aspects of a kinematic plan for a reaching movement, it is unclear whether or how the two regions may differ. We investigated the functional roles of the mIPS and PMd in the planning of reaching movements using high definition transcranial direct current stimulation (HD-tDCS) and examined changes in horizontal endpoint error when participants were subjected to anodal and cathodal stimulation. The left mIPS and PMd were functionally localized with fMRI in each participant using an interleaved center-out pointing and saccade task and mapped onto the scalp using Brainsight. We adopted a randomized, single-blind design and applied anodal and cathodal stimulation (2mA for 20 min; 3cm radius 4x1 electrode placement) during 4 separate visits scheduled at least a week apart. Each participant performed 250 baseline, stimulation, and post-stimulation memory-guided reaches starting from one of two initial hand positions (IHPs) to one of 4 briefly flashed targets (20 cm distant, 5 cm apart horizontally) while fixating on a straight-ahead cross located at the target line. Separate 2-way repeated measures ANOVAs of horizontal endpoint error difference after cathodal tDCS at each stimulation site revealed a significant IHP by target position interaction effect at the left mIPS, and significant IHP and target main effects at the left PMd. Behaviorally, these effects corresponded to IHP-dependent contractions after cathodal mIPS tDCS and IHP-independent contractions after cathodal PMd tDCS. These results suggest that the movement vector is not yet formed at the input level of mIPS, but is encoded at the input of PMd. These results also indicate that tDCS is a viable, useful method in investigating movement planning properties through temporary perturbations of the system.