Laboratory Investigation of Diluted Bitumen Trapping and Dissolution in Gravel

The Canadian economy is largely dependent on the distribution of large volumes of oil to domestic and international markets by a long network of pipelines. Unfortunately, accidents occur, and oil can leak or spill from these pipelines before it reaches its destination. Of particular concern are the long-term consequences of oil spills in freshwater, which include sinking of oil in water and the contamination of sensitive areas, such as where fish (e.g., salmon) deposit their eggs in gravel-dominated river sediments. There is a knowledge gap regarding the fate and behaviour of oil in river sediment. To this end, this study aimed at finding the potential for diluted bitumen (dilbit) oil to become trapped in gravel and to transfer hydrocarbons into water by dissolution, which are harmful to aquatic life. Two sets of laboratory experiments were conducted to simulate conditions of an oil spill on an exposed bank or in shallow water. In the first set, by conducting capillary pressure-saturation (Pc-Sw) experiments it was found that dilbit can enter gravel pores without much resistance and approximately 14% of the pore volume can be occupied by discontinuous single or multipore blobs of dilbit following imbibition of water. Air-water Pc-Sw experiments done in laboratory 1-D columns required gravity correction and could be successfully scaled to predict dilbit-water Pc-Sw curves, except for the trapped amount of dilbit. Trapped dilbit constituents can be dissolved into the water flowing through gravel pores (hyporheic flow) at different velocities. In the second set, dissolution experiments suggested that for the duration of the test, hydrocarbons that cause acute toxicity dissolve rapidly, likely resulting in a decrease in their effective solubility. However, dilbit saturation changed only <2% within that time. Chronically toxic PAH compounds were also detected in the effluent water. The total concentration of all detected PAHs and alkylPAHs exceeded the threshold literature value to protect early-life stage fish. Observations of decreased concentrations with increased aqueous velocities as well as less than equilibrium concentrations indicated that the mass transfer was rate-limited. A correlation was developed for the mass transfer rate coefficient to understand the mass transfer behaviour beyond the conditions used in the experiments, which had a Reynolds number exponent similar to the studies of NAPL dissolution in groundwater.

On the feasibility of time-lapse superconducting gravimetry for reservoir monitoring

The feasibility of monitoring fluid flow subsurface processes that result in density changes, using the iGrav superconducting gravimeter, is investigated. Practical targets include steam-assisted gravity drainage (SAGD) bitumen depletion and water pumping from aquifers, for which there is currently a void in low-impact, inexpensive monitoring techniques. This study demonstrates that the iGrav has the potential to be applied to multi-scale and diverse reservoirs. Gravity and gravity gradient signals are forward modeled for a real SAGD reservoir at two time steps, and for surface-fed and groundwater-fed aquifer pumping models, to estimate signal strength and directional dependency of water flow. Time-lapse gravimetry on small-scale reservoirs exhibits two obstacles, namely, a µgal sensitivity requirement and high noise levels in the vicinity of the reservoir. In this study, both limitations are overcome by proposing (i) a portable superconducting gravimeter, and (ii) a pair of instruments under various baseline geometries. This results in improved spatial resolution for locating depletion zones, as well as the cancellation of noise common in both instruments. Results indicate that a pair of iGrav superconducting gravimeters meet the sensitivity requirements and the spatial focusing desired to monitor SAGD bitumen migration at the reservoir scales. For SAGD reservoirs, the well pair separation, reservoir depth, and survey sampling determine the resolvability of individual well pair depletion patterns during the steam chamber rising phase, and general reservoir depletion patterns during the steam chamber spreading phase. Results show that monitoring water table elevation changes due to pumping and tracking whether groundwater or surface water is being extracted are feasible.

Development of An Enhanced Oil Sands Fluid Tailings Generation Model

Bitumen extraction from surface-mined oil sands results in the production of large volumes of Fluid Fine Tailings (FFT). Through Directive 085, the Province of Alberta has signaled that oil sands operators must improve and accelerate the methods by which they deal with FFT production, storage and treatment. This thesis aims to develop an enhanced method to forecast FFT production based on specific ore characteristics. A mass relationship and mathematical model to modify the Forecasting Tailings Model (FTM) by using fines and clay boundaries, as the two main indicators in FFT accumulation, has been developed. The modified FTM has been applied on representative block model data from an operating oil sands mining venture. An attempt has been made to identify order-of-magnitude associated tailings treatment costs, and to improve financial performance by not processing materials that have ultimate ore processing and tailings storage and treatment costs in excess of the value of bitumen they produce. The results on the real case study show that there is a 53% reduction in total tailings accumulations over the mine life by selectively processing only lower tailings generating materials through eliminating 15% of total mined ore materials with higher potential of fluid fines inventory. This significant result will assess the impact of Directive 082 on mining project economic and environmental performance towards the sustainable development of mining projects.