Wetting and Reaction of Sn-2.8Ag-0.5Cu-1.0Bi Solder with Cu and Ni Substrates

The wettability of newly developed Sn-2.8Ag-0.5Cu-1.0Bi lead-free solder on Cu and Ni substrates was assessed through the wetting balance tests. The wettability assessment parameters such as contact angle (ϑc) and maximum wetting force (Fw) were documented for three solder bath temperatures with three commercial fluxes, namely, no-clean (NC), nonactivated (R), and water-soluble organic acid flux (WS). It was found that the lead-free Sn-2.8Ag-0.5Cu-1.0Bi solder exhibited less wetting force, i.e., poorer wettability, than the conventional Sn-37Pb solder for all flux types and solder bath temperatures. The wettability of Sn-2.8Ag-0.5Cu-1.0Bi lead-free solder on Cu substrate was much higher than that on Ni substrate. Nonwetting for Sn-2.8Ag-0.5Cu-1.0Bi and Sn-Pb solders on Ni substrate occurred when R-type flux was used. A model was built and simulations were performed for the wetting balance test. The simulation results were found very close to the experimental results. It was also observed that larger values of immersion depth resulted in a decrease of the wetting force and corresponding meniscus height, whereas the increase in substrate perimeter enhanced the wettability. The wetting reactions between the solder and Cu/Ni substrates were also investigated, and it was found that Cu atoms diffused into the solder through the intermetallic compounds (IMCs) much faster than did the Ni atoms. Rapid formation of IMCs inhibited the wettability of Sn-2.8Ag-0.5Cu-1.0Bi solder compared to the Sn-Pb solder.

Comparative wetting behavior of Sn-0.7Cu and Sn-0.7Cu-0.3Ni solders on Cu and Ni substrates

Electronic packaging industries are now in great challenge to find a suitable lead-free solder as an interconnection material to replace the conventional SnPb solders. Many solders such as SnCu, SnAg, SnAgCu, SnZn, SnBi have already been proposed as the replacement but none of them has reached the physical and metallurgical properties similar to the SnPb solder. However, wetting is one of the basic problems that make the lead-free solder inferior as compared to the SnPb solder. Therefore, alloying with the help of third, fourth or fifth element is the researchers' interest to improve the wetting behavior of lead-free solders. This paper describes the comparative wetting behavior of Sn-0.7Cu and Sn-0.7Cu-0.3Ni solders on Cu and Ni substrates. Wetting balance tests were performed to assess the wetting behaviors. Three different commercial fluxes namely no-clean (NC), non-activated (R) and water soluble organic acid (WS)fluxes were used to assess the wettability for three solder bath temperatures. It was found that Sn0.7Cu-03Ni solder exhibits better wettability on Cu substrate for NC and WS fluxes whereas reverse results were found for R-type flux. In the case of Ni substrate, Sn-0.7Cu-0.3Ni solder showed better wetting behavior compared to the well-known Sn-0.7Cu solder. Among the three fluxes, R-type flux showed the worst performance. Very large contact angles were documented for both solders with this flux. Higher solder bath temperature lowered the contact angles, increased the wetting forces and enhanced the wettability. Computer modeling of wetting balance test revealed that both the wetting force and meniscus height are inversely proportional to the contact angles. Modeling results also reveal that increase in solder bath depths and radiuses do not affect significantly on the wetting behavior.

Effect of adding 0.3wt% Ni into the Sn-0.7wt% Cu solder - Part II: Growth of intermetallic layer with Cu during wetting and aging

The growth behavior of intermetallic layer with or without adding 0.3 wt% Ni into the Sn-0.7Cu solder was studied during the wetting reaction on Cu-substrate and thereafter in solid-state aging condition. The Cu-solder reaction couple was prepared at 255, 275 and 295 °C for 10 s. The samples reacted at 255 °C were then isothermally aged for 2-14 days at 150 °C. The reaction species formed for the Sn-0.7Cu/Cu and Sn-0.7Cu-0.3Ni/Cu soldering systems were Cu6Sn5 and (CuNi)6Sn5, respectively. The thickness of the intermetallic compounds formed at the solder/Cu interfaces and also in the bulk of both solders increased with the increase of reaction temperature. It was found that Ni-containing Sn-0.7Cu solder exhibited lower growth of intermetallic layer during wetting and in the early stage of aging and eventually exceeded the intermetallic layer thickness of Sn-0.7Cu/Cu soldering system after 6 days of aging. As the aging time proceeds, a non-uniform intermetallic layer growth tendency was observed for the case of Sn-0.7Cu-0.3Ni solder. The growth behavior of intermetallic layer during aging for both solders followed the diffusion-controlled mechanism. The intermetallic layer growth rate constants for Sn-0.7Cu and Sn-0.7Cu-0.3Ni solders were calculated as 1.41 × 10-17 and 1.89 × 10-17 m2/s, respectively which indicated that adding 0.3 wt% Ni with Sn-0.7Cu solder contributed to the higher growth of intermetallic layer during aging. © 2006 Elsevier B.V. All rights reserved.

On the application of variable frequency microwave technology for processing of individual surface mount components

Dual-section variable frequency microwave systems enable rapid, controllable heating of materials within an individual surface mount component in a chip-on=board assembly. The ability to process devices individually allows components with disparate processing requirements to be mounted on the same assembly. The temperature profile induced by the microwave system can be specifically tailored to the needs of the component, allowing optimisation and degree of cure whilst minimising thermomechanical stresses. This paper presents a review of dual-section microwave technology and its application to curing of thermosetting polymer materials in microelectronics applications. Curing processes using both conventional and microwave technologies are assessed and compared. Results indicate that dual-section microwave systems are able to cure individual surface mount packages in a significantly shorter time, at the expense of an increase in thermomechanical stresses and a greater variation in degree of cure.

Rheological characterisation and printing performance of Sn/Ag/Cu solder pastes

Lead-free solder paste printing process accounts for majority of the assembly defects in the electronic manufacturing industry. The study investigates rheological behaviour and stencil printing performance of the lead-free solder pastes (Sn/Ag/Cu). Oscillatory stress sweep test was carried out to study the visco-elastic behaviour of the lead-free solder pastes. The visco-elastic behaviour of the paste encompasses solid and liquid characteristic of the paste, which could be used to study the flow behaviour experienced by the pastes during the stencil printing process. From this study, it was found that the solid characteristics (G0) is higher than the liquid characteristic (G0 0) for the pastes material. In addition, the results from the study showed that the solder paste with a large G0 = G0 0 has a higher cohesiveness resulting in poor withdrawal of the paste during the stencil printing process. The phase angles (d) was used to correlate the quality of the dense suspensions to the formulation of solder paste materials. This study has revealed the value of having a rheological measurement for explaining and characterising solder pastes for stencil printing. As the demand for lead free pastes increases rheological measurements can assist with the formulation or development of new pastes.

Study of the rheological behaviour of Sn-Ag-Cu solder pastes and their correlation with printing performance

Solder paste plays an important role in the electronic assembly process by providing electrical, mechanical and thermal bonding between the components and the substrate. The rheological characterisation of pastes is an important step in the design and development of new paste formulations. With the ever increasing trend of miniaturisation of electronic products, the study of the rheological properties of solder pastes is becoming an integral part in the R&D of new paste formulations and in the quality monitoring and control during paste manufacture and electronic assembly process. This research work outlines some of the novel techniques which can be successfully used to investigate the rheology of leadfree solder pastes. The report also presents the results of the correlation of rheological properties with solder paste printing performance. Four different solder paste samples (namely paste P1, P2, P3 and P4) with different flux vehicle systems and particle size distributions were investigated in the study. As expected, all the paste samples showed shear thinning behaviour. Although the samples displayed similar flow behaviour at high shear rates, differences were observed at low shear rates. In the stencil printing trials, round deposits showed better results than rectangular deposits in terms of paste heights and aperture filling. Our results demonstrate a good correlation between higher paste viscosity and good printing performance. The results of the oscillatory and thixotropy tests were also successfully correlated to the printing behaviour of solder paste.

Individual crisis episodes and cultural transition: finding the macrocosm in the microcosm

According to dialogical self theory (Hermans, 2001), individual identities reflect cultural and subcultural values, and appropriate voices and discourses from the social environment. Bronfenbrenner’s (1979) systemic theory of human development similarly postulates that individual and social development occur in a symbiotic and interdependent fashion. It would therefore be predicted that individual changes in identity reflect macrocosmic changes in cultural values and social structures. The current study investigated narratives of crisis transitions within adults aged 25-40, by way of interviews with 22 participants. An intensive qualitative analysis showed that the narratives of crisis could indeed be viewed as individual manifestations of contemporary cultural changes. National statistics and academic research have documented in the UK substantial cultural shifts over the last twenty years including the lessening popularity of marriage, the rise of freelance and portfolio careers and the growth of accepted alternative gender roles. In individual crises, changes made over the course of the episode were invariably in the same direction as these social changes; towards flexible work patterns, non-marital relationships and redefined gender identities. Before the crisis, participants described their identity as bound into an established discourse of conventionality, a traditional sense of masculinity or feminitity and a singular career role, while after the crisis alternative and fluid identities are explored, and identity is less defined by role and institution. These findings show that changes in the social macrocosm can be found in the individual microcosm, and therefore support dialogical self theory.