Further validation of the buildingEXODUS evacuation model using the Tsukuba dataset

In this paper, the buildingEXODUS (V1.1) evacuation model is described and discussed and attempts at qualitative and quantitative model validation are presented. The data set used for the validation is the Tsukuba pavilion evacuation data. This data set is of particular interest as the evacuation was influenced by external conditions, namely inclement weather. As part of the validation exercise, the sensitivity of the buildingEXODUS predictions to a range of variables and conditions is examined, including; exit flow capacity, occupant response times and the impact of external conditions on the developing evacuation. The buildingEXODUS evacuation model was found to be able to produce good qualitative and quantitative agreement with the experimental data.

Validation of the buildingEXODUS Evacuation Model

In this paper, the buildingEXODUS (V1.1) evacuation model is described and discussed and attempts at qualitative and quantitative model validation are presented. The data sets used for validation are the Stapelfeldt and Milburn House evacuation data. As part of the validation exercise, the sensitivity of the buildingEXODUS predictions to a range of variables is examined, including: occupant drive, occupant location, exit flow capacity, exit size, occupant response times and geometry definition. An important consideration that has been highlighted by this work is that any validation exercise must be scrutinised to identify both the results generated and the considerations and assumptions on which they are based. During the course of the validation exercise, both data sets were found to be less than ideal for the purpose of validating complex evacuation models. However, the buildingEXODUS evacuation model was found to be able to produce reasonable qualitative and quantitative agreement with the experimental data.

A systematic comparison of model predictions produced by the buildingExodus evacuation model and the Tsukuba Pavilion evacuation data

In this article, the buildingEXODUS (V1.1) evacuation model is described and discussed and attempts at qualitative and quantitative model validation are presented. The data set used for the validation is the Tsukuba pavilion evacuation data. This data set is of particular interest as the evacuation was influenced by external conditions, namely inclement weather. As part of the validation exercise, the sensitivity of the buildingEXODUS predictions to a range of variables and conditions is examined, including: exit flow capacity, occupant response times, and the impact of external conditions on the developing evacuation. The buildingEXODUS evacuation model was found to produce good qualitative and quantitative agreement with the experimental data.

A comprehensive copper stockpile leach model: background and parameter sensitivity

The design and development of a comprehensive computational model of a copper stockpile leach process is summarized. The computational fluid dynamic software framework PHYSICA+ and various phenomena were used to model transport phenomena, mineral reaction kinetics, bacterial effects, and heat, energy and acid balances for the overall leach process. In this paper, the performance of the model is investigated, in particular its sensitvity to particle size and ore permeability. A combination of literature and laboratory sources was used to parameterize the model. The simulation results from the leach model are compared with closely controlled column pilot scale tests. The main performance characteristics (e.g. copper recovery rate) predicted by the model compare reasonably well with the experimental data and clearly reflect the qualitiative behavior of the process in many respects. The model is used to provide a measure of the sensitivity of ore permeability on leach behavior, and simulation results are examined for several different particle size distributions.

Finite element modelling of crack detection tests

Four non-destructive tests for determining the length of fatigue cracks within the solder joints of a 2512 surface mount resistor are investigated. The sensitivity of the tests is obtained using finite element analysis with some experimental validation. Three of the tests are mechanically based and one is thermally based. The mechanical tests all operate by applying different loads to the PCB and monitoring the strain response at the top of the resistor. The thermal test operates by applying a heat source underneath the PCB, and monitoring the temperature response at the top of the resistor. From the modelling work done, two of these tests have shown to be sensitive to cracks. Some experimental results are presented but further work is required to fully validate the simulation results.

A systematic comparison of buildingEXODUS predictions with experimental data from the Stapelfeldt trials and the Milburn House evacuation

In this paper, the buildingEXODUS evacuation model is described and discussed and attempts at qualitative and quantitative model validation are presented. The data sets used for validation are the Stapelfeldt and Milburn House evacuation data. As part of the validation exercise, the sensitivity of the building-EXODUS predictions to a range of variables is examined, including occupant drive, occupant location, exit flow capacity, exit size, occupant response times and geometry definition. An important consideration that has been highlighted by this work is that any validation exercise must be scrutinised to identify both the results generated and the considerations and assumptions on which they are based. During the course of the validation exercise, both data sets were found to be less than ideal for the purpose of validating complex evacuation. However, the buildingEXODUS evacuation model was found to be able to produce reasonable qualitative and quantitative agreement with the experimental data.

Investigation into the performance of turbulence models for fluid flow and heat transfer phenomena in electronic applications

Heat is extracted away from an electronic package by convection, conduction, and/or radiation. The amount of heat extracted by forced convection using air is highly dependent on the characteristics of the airflow around the package which includes its velocity and direction. Turbulence in the air is also important and is required to be modeled accurately in thermal design codes that use computational fluid dynamics (CFD). During air cooling the flow can be classified as laminar, transitional, or turbulent. In electronics systems, the flow around the packages is usually in the transition region, which lies between laminar and turbulent flow. This requires a low-Reynolds number numerical model to fully capture the impact of turbulence on the fluid flow calculations. This paper provides comparisons between a number of turbulence models with experimental data. These models included the distance from the nearest wall and the local velocity (LVEL), Wolfshtein, Norris and Reynolds, k-ε, k-ω, shear-stress transport (SST), and kε/kl models. Results show that in terms of the fluid flow calculations most of the models capture the difficult wake recirculation region behind the package reasonably well, although for packages whose heights cause a high degree of recirculation behind the package the SST model appears to struggle. The paper also demonstrates the sensitivity of the models to changes in the mesh density; this study is aimed specifically at thermal design engineers as mesh independent simulations are rarely conducted in an industrial environment.

Computer modelling analysis of the globtop's effects on aluminium wirebond reliability

In power electronics modules, heavy aluminium wires, i.e. wire diameters greater than 100 microns, are bonded to the active semiconductor devices and conductor metallization to form electric circuits of the power electronic module. Due to the high currents that may flow through these wires, a single connection usually contains several wires and thus, a large number of wires are used in a power electronics module. Under normal operation or test condition, a significant amount of stresses and strains induced in the wire and bonding interfaces, resulting in failure over time. In this paper, computer modelling techniques are used to analyse the effect of globtop design on the reliability of aluminium wirebonds under cyclic thermal-mechanical loading conditions. The results will show the sensitivity of the reliability of the wirebonds to the changes in the geometry and the material properties of the wirebond globtop.

Computer simulation of aluminium wirebonds with globtop in power electronics modules

In this paper, computer modelling techniques are used to analyse the effects of globtops on the reliability of aluminium wirebonds in power electronics modules under cyclic thermal-mechanical loading conditions. The sensitivity of the wirehond reliability to the changes of the geometric and the material property parameters of wirebond globtop are evaluated and the optimal combination of the Young's modulus and the coefficient of thermal expansion have been predicted.

Synthesis and properties of polyelectrolyte microgel particles

A series of cationic poly(N-isopropylacrylamide/4-vinylpyridine) [poly(NIPAM/4-VP)] polyelectrolyte co-polymer microgels have been prepared by surfactant free emulsion polymerization (SFEP) with varying compositions of 4-VP and NIPAM. The compositions of 4-VP were 15, 25, 35, 45, 55 wt.% relative to NIPAM. The temperature and pH responsive swelling–deswelling properties of these microgels have been investigated using dynamic light scattering (DLS) and electrophoretic mobility measurements. DLS results have shown that the particle diameter of the poly(NIPAM/4-VP) microgels decreases with increasing concentration (wt.%) of 4-VP over the 20–60 °C temperature range due to the increased amount of hydrophobic group. The particle size of all poly(NIPAM/4-VP) microgel series increases with decreasing pH, as the 4-VP units become more protonated at low pH below the pKa (5.39) of the monomer 4-VP. Electrophoretic mobility results have shown that electrophoretic mobility increases as the temperature/pH increases at a constant background ionic strength (1 × 10− 4 mol dm− 3 NaCl). These results are in good agreement with DLS results. The temperature/pH sensitivity of these microgels depends on the ratio of NIPAM/4-VP concentration in the co-polymer microgel systems. The combined temperature/pH responsiveness of these polyelectrolyte microgels can be used in applications where changes in particle size with small change in pH or temperature is of great consequence.

Segregation of bulk particulates through multiple process handling steps

Segregation or de-blending of bulk particulates is a problem that is encountered in many industrial sectors. The magnitude of segregation can often determine whether a complete production batch can be transferred for onward processing within the plant or released to market. It is a phenomenon that impacts directly upon the profitability of a process. Segregation can occur through a coincidence of a range of variables that relate to the process and bulk particulate properties, common mechanisms for this include; percolation, surface effect (rolling) and elutriation. The importance to industry of predicting the sensitivity of bulk particulates to segregation cannot be under-estimated, and to this end various test procedures have been developed. Within many industries striving to improve product quality and reduce wastage, the determination of variability in blend consistency caused by segregation is an increasing priority. This paper considers recent work undertaken to evaluate the effects of multiple handling operations on the degree of segregation that results. The bulk properties of segregability (and resulting flowability) can not only influence the product consistency, but can have great influence over the process (production) control and performance.