Investigation into the performance of turbulence models for fluid flow and heat transfer phenomena in electronic applications

Computational Fluid Dynamics (CFD) is gradually becoming a powerful and almost essential tool for the design, development and optimization of engineering applications. However the mathematical modelling of the erratic turbulent motion remains the key issue when tackling such flow phenomena. The reliability of CFD analysis depends heavily on the turbulence model employed together with the wall functions implemented. In order to resolve the abrupt changes in the turbulent energy and other parameters situated at near wall regions a particularly fine mesh is necessary which inevitably increases the computer storage and run-time requirements. Turbulence modelling can be considered to be one of the three key elements in CFD. Precise mathematical theories have evolved for the other two key elements, grid generation and algorithm development. The principal objective of turbulence modelling is to enhance computational procedures of efficient accuracy to reproduce the main structures of three dimensional fluid flows. The flow within an electronic system can be characterized as being in a transitional state due to the low velocities and relatively small dimensions encountered. This paper presents simulated CFD results for an investigation into the predictive capability of turbulence models when considering both fluid flow and heat transfer phenomena. Also a new two-layer hybrid kε / kl turbulence model for electronic application areas will be presented which holds the advantages of being cheap in terms of the computational mesh required and is also economical with regards to run-time.

Law in the community: the University of Greenwich/Greenwich Association of Disabled People Centre for Independent Living (GAD) research project

The GAD Advocacy Service is funded by the London Borough of Greenwich Directorate of Neighbourhood Services; its remit to support disabled people experiencing Hate Crime, Domestic Violence and Harassment. Run by disabled personnel and giving advice to all disabled people it is unique in London. Since its inception in 2004, the Advocacy Service has been stretched to its limit - there is a need to extend the remit of the Advocacy Service to give specialist legal advice on other issues. In 2003, the CEDRM-UK project was set up in the University of Greenwich Law Department as part of the Disability Rights Promotion International Legal Education and Research Project; its objectives were firstly, to facilitate the collection of data on the effectiveness of legislation in promoting the rights of disabled persons; and secondly, to pilot new methods in teaching and training in Human Rights Law – students acquire an expertise in Human Rights Law through research into the practical application of legislation relating to civil and human rights in the daily life of the community. In July 2007, GAD and CEDRM-UK embarked on a joint project to report on the work of the Advocacy Service and to create a database to support its caseload. The 2008-9 Project team will report on their work and findings relating to facilitating equality in the workplace; the inclusion of cancer, HIV and multiple sclerosis within the legal definition of disability and the implications of the statutory duty to promote disability equality for the provision of extracurricular activities for schoolchildren. [From the Author]

Ethnic variations in the experiences of mental health service users in England: results of a national patient survey programme

Background: Minority ethnic groups in the UK are reported to have a poor experience of mental health services, but comparative information is scarce. Aims: To examine ethnic differences in patients’ experience of community mental health services. Method: Trusts providing mental health services in England conducted surveys in 2004 and 2005 of users of community mental health services. Multiple regression was used to examine ethnic differences in responses. Results: About 27 000 patients responded to each of the surveys, of whom 10% were of minority ethnic origin. In the 2004 survey, age, living alone, the 2004 survey, age, living alone, detention and hospital admissions were stronger predictors of patient experience than ethnicity. Self-reported mental health status had the strongest explanatory effect. In the 2005 survey, the main negative differences relative to the White British were for Asians. Conclusions: Ethnicity had a smaller effect on patient experience than other variables. Relative to the White British, the Black group did not report negative experiences whereas the Asian group were most likely to respond negatively. However, there is a need for improvements in services for minority ethnic groups, including access to talking therapies and better recording of ethnicity.

Effects of reflow process on the reliability of flip chip on flex interconnections using anisotropic conductive adhesives

In this paper, the effects of the solder reflow process on the reliability of anisotropic conductive film (ACF) interconnections for flip chip on flex (FCOF) applications are investigated. Experiments as well as computer modeling methods have been used. In the experiments, it was found that the contact resistance of ACF joints increased after the subsequent reflow process, and the magnitude of this increase was strongly correlated to the peak temperature of the reflow profile. Nearly 40% of the joints were opened (i.e. lifted away from the pad) after the reflow process with 260 °C peak temperature while no opening was observed when the peak temperature was 210 °C. It is believed that the CTE mismatch between the polymer particle and the adhesive matrix is the main cause of this contact degradation. It was also found that the ACF joints after the reflow process with 210 °C peak temperature showed a high ability to resist water absorption under steady state 85 °C/85%RH conditions, probably because the curing degree of the ACF was improved during the reflow process. To give a good understanding, a 3D model of an ACF joint structure was built and finite element analysis was used to predict the stress distribution in the conductive particles, adhesive matrix and metal pads during the reflow process.

Observations and analysis of a 63-year-old reinforced concrete promenade railing exposed to the North Sea

Despite being exposed to the harsh sea-spray environment of the North Sea at Arbroath, Scotland, for over 63 years, many of the reinforced concrete precast beam elements of the 1.5 km long promenade railing are still in very good condition and show little evidence of reinforcement corrosion. In contrast, railing replacements constructed in about 1968 and in 1993 are almost all badly cracked as a result of extensive corrosion of the longitudinal reinforcement. This is despite the newer concrete appearing to be of better quality than the 1943 concrete. Statistics for maximum crack width for each of the three populations, based on measurements made in 2004 and in 2006, are presented. In situ and laboratory measurements show that the 1943 concrete appears to have high permeability but it also shows high electrical resistivity. Chloride penetration measurements show the 1943 and 1993 concretes to have similar chloride profiles and similar chloride concentrations at the reinforcement bars. This is inconsistent with the 1943 beams showing much less reinforcement corrosion than their later replacements and casts doubt on the conventional practice for durability design focusing on reducing concrete permeability through denser concretes or greater cover.