[Book review] Rights of the Accused, Crime Control and Protection of Victims

Review of: Rights of the Accused, Crime Control and Protection of Victims. Edited by Eliahu Harnon & Alex Stein. A special volume of the Israel Law Review, Vol. 31, Nos. 1-3, Winter-Summer 1997. Published by the Faculty of Law, Hebrew University, Jerusalem.

The effect of thermal cycle profiles on solder joint damage

The relationship between the damage caused at different thermal cycles is very important. The whole of accelerated thermal cycle testing is based on the premise that damage at one cycle is representative of damage at a different cycle. In this paper, the relative damage caused by six thermal cycle profiles are predicted using Finite Element (FE) modelling and the results validated against experiments. Both creep strain and strain energy density were used as damage indicators and creep strain was found to correlate better with experiment. The validated FE model is then used to investigate the effect of altering each of the thermal profile parameters (ramp and swell times, hot and cold temperatures). The components used for testing are surface mount resistors - 1206, 0805 and 0603. The solders investigated are eutectic SnAgCu and eutectic SnAg.

Fatal impact? The effects of emotional arousal and weapon presence on police officers' memories for a simulated crime

Purpose. (1) To investigate the effects of emotional arousal and weapon presence on the completeness and accuracy of police officers' memories; and (2) to better simulate the experience of witnessing a shooting and providing testimony. Methods. A firearms training simulator was used to present 70 experienced police officers with either a shooting or a domestic dispute scenario containing no weapons. Arousal was measured using both self-report and physiological indices. Recall for event details was tested after a 10-minute delay using a structured interview. Identification accuracy was assessed with a photographic line-up. Results. Self-report measures confirmed that the shooting induced greater arousal than did the other scenario. Overall, officers' memories for the event were less complete, but more accurate, when they had witnessed the shooting. The recall and line-up data did not support a weapon focus effect. Conclusions. Police officers' recall performance can be affected both qualitatively and quantitatively by witnessing an arousing event such as a shooting.

Effects of thermal cycling profiles on the performance of chip-on-flex assembly using anisotropic conductive films

Anisotropic conductive films (ACFs) are widely used in the electronic packaging industries because of their fine pitch potential and the assembly process is simpler compared to the soldering process. However, there are still unsolved issues in the volume productions using ACFs. The main reason is that the effects of many factors on the interconnects are not well understood. This work focuses on the performance of ACF-bonded chip-on-flex assemblies subjected to a range of thermal cycling test conditions. Both experimental and three-dimensional finite element computer modelling methods are used. It has been revealed that greater temperature ranges and longer dwell-times give rise to higher stresses in the ACF interconnects. Higher stresses are concentrated along the edges of the chip-ACF interfaces. In the experiments, the results show that higher temperature ranges and prolonged dwell times increase contact resistance values. Close examination of the microstructures along the bond-line through the scanning electron microscope (SEM) indicates that cyclic thermal loads disjoint the conductive particles from the bump of the chip and/or pad of the substrate and this is thought to be related to the increase of the contact resistance value and the failure of the ACF joints.

Chitosan derivatives alter release profiles of model compounds from calcium phosphate implants

The aim of the current study was to evaluate the impact of chitosan derivatives, namely N-octyl-chitosan and N-octyl-O-sulfate chitosan, incorporated in calcium phosphate implants to the release profiles of model drugs. The rate and extent of calcein (on M.W. 650 Da) ED, and FITC-dextran (M.W. 40 kDa) on in vitro release were monitored by fluorescence spectroscopy. Results show that calcein release is affected by the type of chitosan derivative used. A higher percentage of model drug was released when the hydrophilic polymer N-octyl-sulfated chitosan was present in the tablets compared with the tablets containing the hydrophobic polymer N-octyl-chitosan. The release profiles of calcein or FD from tablets containing N-octyl-O-sulfate revealed a complete release for FD after 120 h compared with calcein where 20% of the drug was released over the same time period. These results suggest that the difference in the release profiles observed from the implants is dependent on the molecular weight of the model drugs. These data indicate the potential of chitosan derivatives in controlling the release profile of active compounds from calcium phosphate implants. (C) 2009 Elsevier Ltd. All rights reserved.

From Agatha Christie to Ruth Rendell: British women writers in detective and crime fiction

This work considers, seriously, the hugely popular and influential works of Agatha Christie, Dorothy L.Sayers, Margery Allingham, Ngaio Marsh, P.D. James and Ruth Rendell/Barbara Vine. Providing studies of 42 key novels, it introduces these authors for students and the general reader within the contexts of their lives, and critical debates on gender, colonialism, psychoanalysis, the Gothic, and feminism. It includes interviews with P.D. James and Ruth Rendell/Barbara Vine. [From the Publisher]

Measurement of pressure profiles in pneumatic conveying pipelines

Accurate design of two-phase air-solid pipelines requires data from flow and pressure measurements, requiring the appropriate positioning and selection of sensors as well as judicious processing of signals. This paper shows how detailed measurements of pressure profiles have been obtained for use in design of improved pneumatic conveying pipelines.

Laser Doppler velocimetry measurements of particle velocity profiles in gas-solid two-phase flows

The measurement of particle velocities in two-phase gas-solid systems has a wide application in flow monitoring in process plant, where two-phase gas-solids systems are frequently employed in the form of pneumatic conveyors and solid fuel injection systems. Such measurements have proved to be difficult to make reliably in industrial environments. This paper details particle velocity measurements made in a two phase gas-solid now utilising a laser Doppler velocimetry system. Tests were carried out using both wheat flour and pulverised coal as the solids phase, with air being used as the gaseous phase throughout. A pipeline of circular section, having a diameter of 53 mm was used for the test work, with air velocities ranging from 25 to 45 m/s and suspension densities ranging from 0.001 kg to 1 kg of solids per cubic meter of air. Details of both the test equipment used, and the results of the measurements are presented.