Obtaining data to validate a model of an induction skull melting furnace

A casting route is often the most cost-effective means of producing engineering components. However, certain materials, particularly those based on Ti, TiAl and Zr alloy systems, are very reactive in the molten condition and must be melted in special furnaces. Induction Skull Melting (ISM) is the most widely-used process for melting these alloys prior to casting components such as turbine blades, engine valves, turbocharger rotors and medical prostheses. A major research project is underway with the specific target of developing robust techniques for casting TiAl components. The aims include increasing the superheat in the molten metal to allow thin section components to be cast, improving the quality of the cast components and increasing the energy efficiency of the process. As part of this, the University of Greenwich (UK) is developing a computer model of the ISM process in close collaboration with the University of Birmingham (UK) where extensive melting trials are being undertaken. This paper describes the experimental measurements to obtain data to feed into and to validate the model. These include measurements of the true RMS current applied to the induction coil, the heat transfer from the molten metal to the crucible cooling water, and the shape of the column of semi-levitated molten metal. Data are presented for Al, Ni and TiAl.

Investigating the representation of merging behavior at the floor–stair interface in computer simulations of multi-floor building evacuations

In this article, the representation of the merging process at the floor— stair interface is examined within a comprehensive evacuation model and trends found in experimental data are compared with model predictions. The analysis suggests that the representation of floor—stair merging within the comprehensive model appears to be consistent with trends observed within several published experiments of the merging process. In particular: (a) The floor flow rate onto the stairs decreases as the stair population density increases. (b) For a given stair population density, the floor population's flow rate onto the stairs can be maximized by connecting the floor to the landing adjacent to the incoming stair. (c) In situations where the floor is connected adjacent to the incoming stair, the merging process appears to be biased in favor of the floor population. It is further conjectured that when the floor is connected opposite the incoming stair, the merging process between the stair and floor streams is almost in balance for high stair population densities, with a slight bias in favor of the floor stream at low population densities. A key practical finding of this analysis is that the speed at which a floor can be emptied onto a stair can be enhanced simply by connecting the floor to the landing at a location adjacent to the incoming stair rather than opposite the stair. Configuring the stair in this way, while reducing the floor emptying time, results in a corresponding decrease in the descent flow rate of those already on the stairs. While this is expected to have a negligible impact on the overall time to evacuate the building, the evacuation time for those higher up in the building is extended while those on the lower flows is reduced. It is thus suggested that in high-rise buildings, floors should be connected to the landing on the opposite side to the incoming stair. Information of this type will allow engineers to better design stair—floor interfaces to meet specific design objectives.

Self-optimising data farming for web applications

Many Web applications walk the thin line between the need for dynamic data and the need to meet user performance expectations. In environments where funds are not available to constantly upgrade hardware inline with user demand, alternative approaches need to be considered. This paper introduces a ‘Data farming’ model whereby dynamic data, which is ‘grown’ in operational applications, is ‘harvested’ and ‘packaged’ for various consumer markets. Like any well managed agricultural operation, crops are harvested according to historical and perceived demand as inferred by a self-optimising process. This approach aims to make enhanced use of available resources through better utlilisation of system downtime - thereby improving application performance and increasing the availability of key business data.

'Re-using an existing wheel' developing data architecture for cooperating autonomous and semi-autonomous, agent-based web services

This short position paper considers issues in developing Data Architecture for the Internet of Things (IoT) through the medium of an exemplar project, Domain Expertise Capture in Authoring and Development ­Environments (DECADE). A brief discussion sets the background for IoT, and the development of the ­distinction between things and computers. The paper makes a strong argument to avoid reinvention of the wheel, and to reuse approaches to distributed heterogeneous data architectures and the lessons learned from that work, and apply them to this situation. DECADE requires an autonomous recording system, ­local data storage, semi-autonomous verification model, sign-off mechanism, qualitative and ­quantitative ­analysis ­carried out when and where required through web-service architecture, based on ontology and analytic agents, with a self-maintaining ontology model. To develop this, we describe a web-service ­architecture, ­combining a distributed data warehouse, web services for analysis agents, ontology agents and a ­verification engine, with a centrally verified outcome database maintained by certifying body for qualification/­professional status.