10 resultados para Turbulence

em Greenwich Academic Literature Archive - UK


Relevância:

20.00% 20.00%

Publicador:

Resumo:

This paper describes work performed at IRSID/USINOR in France and the University of Greenwich, UK, to investigate flow structures and turbulence in a water-model container, simulating aspects typical of metal tundish operation. Extensive mean and fluctuating velocity measurements were performed at IRSID using LDA to determine the flow field and these form the basis for a numerical model validation. This apparently simple problem poses several difficulties for the CFD modelling. The flow is driven by the strong impinging jet at the inlet. Accurate description of the jet is most important and requires a localized fine grid, but also a turbulence model that predicts the correct spreading rates of jet and impinging wall boundary layers. The velocities in the bulk of the tundish tend to be (indeed need to be) much smaller than those of the jet, leading to damping of turbulence, or even laminar flow. The authors have developed several low-Reynolds number (low-Re) k–var epsilon model variants to compute this flow and compare against measurements. Best agreement is obtained when turbulence damping is introduced to account not only for walls, but also for low-Re regions in the bulk – the k–var epsilon model otherwise allows turbulence to accumulate in the container due to the restricted outlet. Several damping functions are tested and the results reported here. The k–ω model, which is more suited to transitional flow, also seems to perform well in this problem.

Relevância:

20.00% 20.00%

Publicador:

Resumo:

This paper presents simulated computational fluid dynamics (CFD) results for comparison against experimental data. The performance of four turbulence models has been assessed for electronic application areas considering both fluid flow and heat transfer phenomenon. CFD is vast becoming a powerful and almost essential tool for design, development and optimization in engineering problems. However turbulence models remain to be the key problem issue when tackling such flow phenomena. The reliability of CFD analysis depends heavily on the performance of the turbulence model employed together with the wall functions implemented. To be able to resolve the abrupt changes in the turbulent energy and other parameters near the wall a particularly fine mesh is necessary which unfortunately increases the computer storage capacity requirements. The objective of turbulence modelling is to enhance computational procdures of sufficient acccuracy and generality for engineers to anticipate the Reynolds stresses and the scalar transport terms.

Relevância:

20.00% 20.00%

Publicador:

Resumo:

The electronics industry is developing rapidly together with the increasingly complex problem of microelectronic equipment cooling. It has now become necessary for thermal design engineers to consider the problem of equipment cooling at some level. The use of Computational Fluid Dynamics (CFD) for such investigations is fast becoming a powerful and almost essential tool for the design, development and optimisation of engineering applications. However turbulence models remain a key issue when tackling such flow phenomena. The reliability of CFD analysis depends heavily on the turbulence model employed together with the wall functions implemented. In order to resolve the abrupt fluctuations experienced by the turbulent energy and other parameters located at near wall regions and shear layers a particularly fine computational mesh is necessary which inevitably increases the computer storage and run-time requirements. This paper will discuss results from an investigation into the accuract of currently used turbulence models. Also a newly formulated transitional hybrid turbulence model will be introduced with comparisonsaagainst experimental data.

Relevância:

20.00% 20.00%

Publicador:

Resumo:

The electronics industry and the problems associated with the cooling of microelectronic equipment are developing rapidly. Thermal engineers now find it necessary to consider the complex area of equipment cooling at some level. This continually growing industry also faces heightened pressure from consumers to provide electronic product miniaturization, which in itself increases the demand for accurate thermal management predictions to assure product reliability. Computational fluid dynamics (CFD) is considered a powerful and almost essential tool for the design, development and optimization of engineering applications. CFD is now widely used within the electronics packaging design community to thermally characterize the performance of both the electronic component and system environment. This paper discusses CFD results for a large variety of investigated turbulence models. Comparison against experimental data illustrates the predictive accuracy of currently used models and highlights the growing demand for greater mathematical modelling accuracy with regards to thermal characterization. Also a newly formulated low Reynolds number (i.e. transitional) turbulence model is proposed with emphasis on hybrid techniques.

Relevância:

20.00% 20.00%

Publicador:

Resumo:

This paper will discuss Computational Fluid Dynamics (CFD) results from an investigation into the accuracy of several turbulence models to predict air cooling for electronic packages and systems. Also new transitional turbulence models will be proposed with emphasis on hybrid techniques that use the k-ε model at an appropriate distance away from the wall and suitable models, with wall functions, near wall regions. A major proportion of heat emitted from electronic packages can be extracted by air cooling. This flow of air throughout an electronic system and the heat extracted is highly dependent on the nature of turbulence present in the flow. The use of CFD for such investigations is fast becoming a powerful and almost essential tool for the design, development and optimization of engineering applications. However turbulence models remain a key issue when tackling such flow phenomena. The reliability of CFD analysis depends heavily on the turbulence model employed together with the wall functions implemented. In order to resolve the abrupt fluctuations experienced by the turbulent energy and other parameters located at near wall regions and shear layers a particularly fine computational mesh is necessary which inevitably increases the computer storage and run-time requirements. The PHYSICA Finite Volume code was used for this investigation. With the exception of the k-ε and k-ω models which are available as standard within PHYSICA, all other turbulence models mentioned were implemented via the source code by the authors. The LVEL, LVEL CAP, Wolfshtein, k-ε, k-ω, SST and kε/kl models are described and compared with experimental data.

Relevância:

20.00% 20.00%

Publicador:

Resumo:

A major percentage of the heat emitted from electronic packages can be extracted by air cooling whether by means of natural or forced convection. This flow of air throughout an electronic system and the heat extracted is highly dependable on the nature of turbulence present in the flow field. This paper will discuss results from an investigation into the accuracy of turbulence models to predict air cooling for electronic packages and systems.

Relevância:

20.00% 20.00%

Publicador:

Resumo:

Computational Fluid Dynamics (CFD) is gradually becoming a powerful and almost essential tool for the design, development and optimization of engineering applications. However the mathematical modelling of the erratic turbulent motion remains the key issue when tackling such flow phenomena. The reliability of CFD analysis depends heavily on the turbulence model employed together with the wall functions implemented. In order to resolve the abrupt changes in the turbulent energy and other parameters situated at near wall regions a particularly fine mesh is necessary which inevitably increases the computer storage and run-time requirements. Turbulence modelling can be considered to be one of the three key elements in CFD. Precise mathematical theories have evolved for the other two key elements, grid generation and algorithm development. The principal objective of turbulence modelling is to enhance computational procedures of efficient accuracy to reproduce the main structures of three dimensional fluid flows. The flow within an electronic system can be characterized as being in a transitional state due to the low velocities and relatively small dimensions encountered. This paper presents simulated CFD results for an investigation into the predictive capability of turbulence models when considering both fluid flow and heat transfer phenomena. Also a new two-layer hybrid kε / kl turbulence model for electronic application areas will be presented which holds the advantages of being cheap in terms of the computational mesh required and is also economical with regards to run-time.

Relevância:

20.00% 20.00%

Publicador:

Resumo:

Heat is extracted away from an electronic package by convection, conduction, and/or radiation. The amount of heat extracted by forced convection using air is highly dependent on the characteristics of the airflow around the package which includes its velocity and direction. Turbulence in the air is also important and is required to be modeled accurately in thermal design codes that use computational fluid dynamics (CFD). During air cooling the flow can be classified as laminar, transitional, or turbulent. In electronics systems, the flow around the packages is usually in the transition region, which lies between laminar and turbulent flow. This requires a low-Reynolds number numerical model to fully capture the impact of turbulence on the fluid flow calculations. This paper provides comparisons between a number of turbulence models with experimental data. These models included the distance from the nearest wall and the local velocity (LVEL), Wolfshtein, Norris and Reynolds, k-ε, k-ω, shear-stress transport (SST), and kε/kl models. Results show that in terms of the fluid flow calculations most of the models capture the difficult wake recirculation region behind the package reasonably well, although for packages whose heights cause a high degree of recirculation behind the package the SST model appears to struggle. The paper also demonstrates the sensitivity of the models to changes in the mesh density; this study is aimed specifically at thermal design engineers as mesh independent simulations are rarely conducted in an industrial environment.

Relevância:

20.00% 20.00%

Publicador:

Resumo:

This paper is intended to provide a general review of the current capabilities of turbulence models within the specific area of electronic cooling. The work discussed in this paper is aimed at examining currently available turbulence models and the formulation of a new two-layer hybrid kElki model which is specifically designed for electronic application areas. A classic backward facing step configuration will be used to evaluate the performance of the turbulence models in the prediction of separated flows. The preliminary results suggest that the hybrid ke/kl turbulence model is a promising zonal model to pursue.

Relevância:

20.00% 20.00%

Publicador:

Resumo:

This paper concerns the development and validation (using an oil/water system) of a finite volume computer model of the continuous casting process for steel flat products. The emphasis is on hydrodynamic aspects and in particular the dynamic behaviour of the metal/slag interface. Instability and wave action encourage the entrainment of inclusions into the melt affecting product quality. To track the interface between oil and water a new implicit algorithm was developed, called the Counter Diffusion Method. To prevent excessive damping, a time-filtered version of the k-e model, was found necessary, with appropriate density stratification terms representing interface turbulence damping.