Liquid metal turbulent flow dynamics in a cylindrical container with free surface: experiment and numerical analysis

The liquid metal flow in induction crucible models is known to be unstable, turbulent and difficult to predict in the regime of medium frequencies when the electromagnetic skin-layer is of considerable extent. We present long term turbulent flow measurements by a permanent magnet incorporated potential difference velocity probe in a cylindrical container filled with eutectic melt In-Ga-Sn. The parallel numerical simulation of the long time scale development of the turbulent average flow is presented. The numerical flow model uses an implicit pseudo-spectral code and k-w turbulence model, which was recently developed for the transitional flow modelling. The results compare reasonably to the experiment and demonstrate the time development of the turbulent flow field and the turbulence energy.

Liquid metal turbulent flow dynamics in a cylindrical container with free surface: experiment and numerical analysis

The liquid metal flow in inducation crucible models is known to be higly unstable and turbutlen in the regim e of medium frequecies when the elctronmagnetic skin-layer is of considerable extent. We present long term turbulent flow measurements by a permanent magnet incorporated potential difference veolocity probe in a cylindirical container filled with eutecti mlt In-Ga-SN. The parallel numerical simulation of the long time scale development of the turbulen average flow is presented. The numerical lfow model uses a pseud-spectral code and k-w turbulence model, which was recently developed for the transitional flow modelling. The result compare reasonably to the experiment and demonstrate the time development of the turbulent flow field.

An experimental and numerical CFD study of turbulence in a tundish container

This paper describes work performed at IRSID/USINOR in France and the University of Greenwich, UK, to investigate flow structures and turbulence in a water-model container, simulating aspects typical of metal tundish operation. Extensive mean and fluctuating velocity measurements were performed at IRSID using LDA to determine the flow field and these form the basis for a numerical model validation. This apparently simple problem poses several difficulties for the CFD modelling. The flow is driven by the strong impinging jet at the inlet. Accurate description of the jet is most important and requires a localized fine grid, but also a turbulence model that predicts the correct spreading rates of jet and impinging wall boundary layers. The velocities in the bulk of the tundish tend to be (indeed need to be) much smaller than those of the jet, leading to damping of turbulence, or even laminar flow. The authors have developed several low-Reynolds number (low-Re) k–var epsilon model variants to compute this flow and compare against measurements. Best agreement is obtained when turbulence damping is introduced to account not only for walls, but also for low-Re regions in the bulk – the k–var epsilon model otherwise allows turbulence to accumulate in the container due to the restricted outlet. Several damping functions are tested and the results reported here. The k–ω model, which is more suited to transitional flow, also seems to perform well in this problem.

Investigation into the performance of turbulence models for fluid flow and heat transfer phenomena in electronic applications

Computational Fluid Dynamics (CFD) is gradually becoming a powerful and almost essential tool for the design, development and optimization of engineering applications. However the mathematical modelling of the erratic turbulent motion remains the key issue when tackling such flow phenomena. The reliability of CFD analysis depends heavily on the turbulence model employed together with the wall functions implemented. In order to resolve the abrupt changes in the turbulent energy and other parameters situated at near wall regions a particularly fine mesh is necessary which inevitably increases the computer storage and run-time requirements. Turbulence modelling can be considered to be one of the three key elements in CFD. Precise mathematical theories have evolved for the other two key elements, grid generation and algorithm development. The principal objective of turbulence modelling is to enhance computational procedures of efficient accuracy to reproduce the main structures of three dimensional fluid flows. The flow within an electronic system can be characterized as being in a transitional state due to the low velocities and relatively small dimensions encountered. This paper presents simulated CFD results for an investigation into the predictive capability of turbulence models when considering both fluid flow and heat transfer phenomena. Also a new two-layer hybrid kε / kl turbulence model for electronic application areas will be presented which holds the advantages of being cheap in terms of the computational mesh required and is also economical with regards to run-time.

Investigation into the performance of turbulence models for fluid flow and heat transfer phenomena in electronic applications

Heat is extracted away from an electronic package by convection, conduction, and/or radiation. The amount of heat extracted by forced convection using air is highly dependent on the characteristics of the airflow around the package which includes its velocity and direction. Turbulence in the air is also important and is required to be modeled accurately in thermal design codes that use computational fluid dynamics (CFD). During air cooling the flow can be classified as laminar, transitional, or turbulent. In electronics systems, the flow around the packages is usually in the transition region, which lies between laminar and turbulent flow. This requires a low-Reynolds number numerical model to fully capture the impact of turbulence on the fluid flow calculations. This paper provides comparisons between a number of turbulence models with experimental data. These models included the distance from the nearest wall and the local velocity (LVEL), Wolfshtein, Norris and Reynolds, k-ε, k-ω, shear-stress transport (SST), and kε/kl models. Results show that in terms of the fluid flow calculations most of the models capture the difficult wake recirculation region behind the package reasonably well, although for packages whose heights cause a high degree of recirculation behind the package the SST model appears to struggle. The paper also demonstrates the sensitivity of the models to changes in the mesh density; this study is aimed specifically at thermal design engineers as mesh independent simulations are rarely conducted in an industrial environment.