Modelling continuum mechanics phenomena using three dimensional unstructured meshes on massively parallel processors

The difficulties encountered in implementing large scale CM codes on multiprocessor systems are now fairly well understood. Despite the claims of shared memory architecture manufacturers to provide effective parallelizing compilers, these have not proved to be adequate for large or complex programs. Significant programmer effort is usually required to achieve reasonable parallel efficiencies on significant numbers of processors. The paradigm of Single Program Multi Data (SPMD) domain decomposition with message passing, where each processor runs the same code on a subdomain of the problem, communicating through exchange of messages, has for some time been demonstrated to provide the required level of efficiency, scalability, and portability across both shared and distributed memory systems, without the need to re-author the code into a new language or even to support differing message passing implementations. Extension of the methods into three dimensions has been enabled through the engineering of PHYSICA, a framework for supporting 3D, unstructured mesh and continuum mechanics modeling. In PHYSICA, six inspectors are used. Part of the challenge for automation of parallelization is being able to prove the equivalence of inspectors so that they can be merged into as few as possible.

Numerical modelling of adsorption of metallic particles on graphite substrate via molecular dynamics simulation

A computer-based numerical modelling of the adsorption process of gas phase metallic particles on the surface of a graphite substrate has been performed via the application of molecular dynamics simulation method. The simulation relates to an extensive STM-based experiment performed in this field, and reproduces part of the experimental results. Both two-body and many-body inter-atomic potentials have been employed. A Morse-type potential describing the metal-carbon interactions at the interface was specifically formulated for this modelling. Intercalation of silver in graphite has been observed as well as the correct alignments of monomers, dimers and two-dimensional islands on the surface. PACS numbers: 02.60.Cb, 07.05.Tp, 68.55.-a, 81.05.Tp

Multiple reflow study of ball grid array (BGA) solder joints on Au/Ni metallization

This paper evaluates the shearing behavior of ball grid array (BGA) solder joints on Au/Ni/Cu pads of FR4 substrates after multiple reflow soldering. A new Pb-free solder, Sn–3Ag–0.5Cu–8In (SACI), has been compared with Sn–3Ag–0.5Cu (SAC) and Sn–37Pb (SP) solders, in terms of fracture surfaces, shearing forces and microstructures. Three failure modes, ball cut, a combination of solder shear and solder/pad bond separation, and pad lift, are assessed for the different solders and reflow cycles. It is found that the shearing forces of the SP and SAC solder joints tend to increase slightly with an increase in the number of reflow cycles due to diffusion-induced solid solution strengthening of the bulk solder and augmentation of the shearing area. However, the shearing forces of the SACI solder joints decrease slightly after four cycles of reflow, which is ascribed to the thermal degradation of both the solder/intermetallic compound (IMC) and IMC/Ni interfaces. The SACI solder joints yield the highest strengths, whereas the SP solder joints give the smallest values, irrespective of the number of reflow cycles. Thickening of the interfacial IMC layer and coarsening of the dispersing IMC particles within the bulk solders were also observed. Nevertheless, the variation of shearing forces and IMC thickness with different numbers of reflow cycles was not so significant since the Ni under layer acted as an effective diffusion barrier. In addition, the initially-formed IMC layer retarded the further extensive dissolution of the pad material and its interaction with the solder

The impact of the nursing workforce on patient outcomes in intensive care

Introduction: Evidence from studies conducted mainly in the US and mainland Europe suggests that characteristics of the workforce, such as nurse patient ratios and workload (measured in a number of different ways) may be linked to variations in patient outcomes across health care settings (Carmel and Rowan 2001). Few studies have tested this relationship in the UK thus questions remain about whether we are justified in extrapolating evidence from studies conducted in very different health care systems. Objectives: To investigate whether characteristics of the nursing workforce affect patient mortality UK Intensive Care Units. Data: Patient data came from the case mix programme, Intensive Care National Audit and Research Centre (ICNARC), while information about the units came from a survey of all ICUs in England (Audit Comission 1998). The merged data set contained information on 43,859 patients in 69 units across England. ICNARC also supplied a risk adjustment variable to control for patient characteristics that are often the most important determinants of survival. Methods: Multivariate multilevel logistic regression. Findings: Higher numbers of direct care nurses and lower scores on measures of workload(proportion of occupied beds at the time the patient was admitted and mean daily transfers into the unit) were associated with lower mortality rates. Furthermore, the effect of the number of direct care nurses was greatest on the life chances of the patients who were most at risk of dying. Implications: This study has wide implications for workforce policy and planning because it shows that the size of the nursing workforce is associated with mortality (West et al 2006). Few studies have demonstrated this relationship in the UK. This study has a number of strengths and weaknesses and further research is required to determine whether this relationship between the nursing workforce and patient outcomes is causal.