An introduction to China's rail transport Part 2: Urban rail transit systems, highway transport and the reform of China's railways

In this paper, an introduction is provided to some of the components of China's transport system. The authors include the urban rail transit systems, the highway transport systems and its competition for China's railways and the reform of China's railway industry. This is the second of two papers on the situation of rail transport in China.

An introduction to China's rail transport Part 1: History, present and future of China's railways

In this paper an introduction is given to the history, current situation and future plans of China's railway industry. The history of China's railway is divided into four development phases: the phase in Imperial China, the phase in the Republic of China and the phases before and after the economic rejuvenation of the People's Republic of China. An introduction to the current situation and future plans includes the major projects under construction and development trends of China's railways. The environment of China's railways is also presented. This is the first of two papers on the railway scene in China.

Analysis of the structural characteristics of an intermediate rail vehicle and their effect on vehicle crash performance

In the current paper, the authors present an analysis of the structural characteristics of an intermediate rail vehicle and their effects on crash performance of the vehicle. Theirs is a simulation based analysis involving four stages. First, the crashworthiness of the vehicle is assessed by simulating an impact of the vehicle with a rigid wall. Second, the structural characteristics of the vehicle are analysed based on the structural behaviour during this impact and then the structure is modified. Third, the modified vehicle is tested again in the same impact scenario with a rigid wall. Finally, the modified vehicle is subjected to a modelled head-on impact which mirrors the real-life impact interface between two intermediate vehicles in a train impact. The emphasis of the current study is on the structural characteristics of the intermediate vehicle and the differences compared to an impact of a leading vehicle. The study shows that, similar to a leading vehicle, bending, or jackknifing is a main form of failure in this conventionally designed intermediate vehicle. It has also been found that the location of the door openings creates a major difference in the behaviour of an intermediate vehicle. It causes instability of the vehicle in the door area and leads to high stresses at the joint of the end beam with the solebar and shear stresses at the joint of the inner pillar with the cantrail. Apart from this, the shapes of the vehicle ends and impact interfaces are also different and have an effect on the crash performance of the vehicles. The simulation results allow the identification of the structural characteristics and show the effectiveness of relevant modifications. The conclusions have general relevance for the crashworthiness of rail vehicle design

[Book review] Reviews. Peter Aughton, The Transit of Venus: The Brief, Brilliant Life of Jeremiah Horrocks, Father of British Astronomy, Orion, 2004

Book review of: Peter Aughton, The Transit of Venus: The Brief, Brilliant Life of Jeremiah Horrocks, Father of British Astronomy, Orion, 2004, 0-297-84721-x, £18.99.

Issues in delivering multimedia content to mobile devices

The scalability of a computer system is its response to growth. It is also depended on its hardware, its operating system and the applications it is running. Most distributed systems technology today still depends on bus-based shared memory which do not scale well, and systems based on the grid or hypercube scheme requires significantly less connections than a full inter-connection that would exhibit a quadratic growth rate. The rapid convergence of mobile communication, digital broadcasting and network infrastructures calls for rich multimedia content that is adaptive and responsive to the needs of individuals, businesses and the public organisations. This paper will discuss the emergence of mobile Multimedia systems and provides an overview of the issues regarding design and delivery of multimedia content to mobile devices.

Rapid solutions for application specific IGBT module design

The electric car, the all electric aircraft and requirements for renewable energy are prime examples of potential technologies needing to be addressed in the world problem of global warming/carbon emission etc. Power electronics are fundamental for the underpinning of these technologies and with the diverse requirements for electrical configurations and the range of environmental conditions, time to market is paramount for module manufacturers and systems designers alike. This paper presents a 'virtual' design methodology together with theoretical and experimental results that demonstrate enhanced product design with improved reliability, performance and cost value within competitive schemes.

Advanced microwave oven for rapid curing of encapsulant

The curing of a thermosetting polymer materials utilized on micro-electronics packaging applications can be performed using microwave systems. The use of microwave energy enables the cure process to be completed more rapidly than with alternative approaches due to the ability to heat volumetrically. Furthermore, advanced dual-section microwave systems enable curing of individual components on a chip-on-board assembly. The dielectric properties of thermosetting polymer materials, commonly used in microelectronics packaging applications, vary significantly with temperature and degree of cure. The heating rate within a material subjected to an electric field is primarily dependant on the dielectric loss properties of the material itself. This article examines the variation in dielectric properties of a commercially available encapsulant paste with frequency and temperature and the resulting influence on the cure process. The 'FAMOBS' dual section microwave system and its application to microelectronics manufacture are described. The measurement of the dielectric properties of 'Henkel EO1080' encapsulant paste uses a commercially available 'dielectric probe kit' and is described in this paper. The FAMOBS heating system is used to encapsulate a small op-amp chip. A numerical model formulated to assess the cure process in thermosetting polymer materials under microwave heating is outlined. Numerical results showing that the microwave processing systems is capable of rapidly and evenly curing thermosetting polymer materials are presented.

The use of acoustic emission monitoring to rank paper materials with respect to their fracture toughness

In this study, a simplified Acoustic Emission (AE) equipment, in essence an AE signal conditioner and a USB (Universal Serial Bus) data acquisition system, is used to study what happens in paper structures during mechanical loading. By the use of such equipment, some parameters that can be extracted are e.g. the stress and strain at onset of AE, the stress and strain at the onset of rapid AE defined as some numerical factor (larger then one) times the initial emission rate, the emission rate at the first stage of loading and the stress and strain at final failure i.e. when the specimen loses its load carrying ability.In this study however, the interest is focused on one particular parameter i.e. the elastic strain energy density W c at onset of AE. This is a parameter with a clear physical meaning and in this study, the correlation between this parameter and a fracture toughness measure, is investigated.The conclusion is that when nine different paper materials (with a large span regarding properties) are considered, there is a correlation (however not linear) between these two parameters.

Slicing issues in CAD translation to STL in rapid prototyping

The rapid prototyping (RP) process is being used widely with great potential for rapid manufacturing of functional parts. The RP process involves translation of the CAD file to STL format followed by slicing of the model into multiple horizontal layers, each of which is reproduced physically in making the prototype. The thickness of the resulting slices has a profound effect on the surface finish and build time of the prototype. The purpose of this paper is to show the effects of slice thickness on the surface finish, layering error, and build time of a prototype, as well as to show how an efficient STL file can be developed. Three objects were modeled and STL files were generated. One STL file for each object was sliced using different slice thicknesses, and the build times were obtained. Screenshots were used to show the slicing effect on layering error and surface finish and to demonstrate the means to a more efficient STL file. From the results, it is clear that the surface finish and build time are important factors that are affected by slice thickness