Effect of machine dependence on wall failure property measurements, Jenike versus an annular shear tester

Annular, ring or torsional shear testers are commonly used in bulk solids handling research for the purpose of powder characterisation or equipment design. This paper reports from a DEFRA sponsored project which aims to develop an industrial powder flow-ability tester, (based on the annular shear tester) that is economic to buy and quick and easy to use in trained but unskilled hands. This paper compares the wall failure loci measured with an annular shear cell with measurements obtained using the accepted standard wall friction tester, the Jenike shear cell. These wall failure loci have been measured for several bulk solids which range from fine cohesive powders to free-flowing granular materials, on a stainless steel 304 2B wall surface.

Comparisons between “sand blast” and “centripetal effect accelerator” type erosion testers

There are two major types of erosion testing devices that are used throughout the world for quantifying particle impact erosion against a solid surface. The first of these uses pressurised air to accelerate abrasive particles through a nozzle so that they impinge upon a target specimen. The second adopts a rotating disc to accelerate abrasive particles using the centripetal effect so that they impinge upon a series of targets arranged around the periphery of the disc. This paper reports the findings of a collaborative project that was designed to compare the performance and results obtained from a rig of each of the two types mentioned above. The sand blast type rig was provided by The Department of Powder Science Technology (POSTEC) at The Telemark Technological Research and Development Centre (TEL-TEK), Porsgrunn, Norway while the centripetal effect accelerator was provided by The Wolfson Centre for Bulk Solids Handling Technology, University of Greenwich, London, UK. The test programme included tests against a wide range of materials that are commonly used in pneumatic handling facilities. (Pneumatic handling is a means of conveying and transporting powders and granular solid materials in bulk in industrial process plant, through pipelines using a gas as the carrier medium.) Olivine sand was used as the abrasive and it was projected against the test specimens at velocities and concentrations commensurate with those seen in pneumatic conveyors. In all instances the materials used in the test programme were taken from the same batch so that scatter of experimental results due to specimen variation was minimised. The paper contains a series of recommendations for erosion testing equipment. A discussion based on the results and their applicability to the prediction of wear in pneumatic conveyors concludes the paper.

Caking strength of granulated clay under frozen conditions

Transport of particulate clay occurs during some extremely cold weather conditions typically in the winter in the far North area. During the transport and temporary storage time, the clay may cake inside a rail or road wagon or in a silo, and consequently be difficult to be discharged from the containers. This paper studied caking strength of a granulated clay powder with a certain water moisture content of 18% for influences of temperature, packing stress and freezing time. The temperature tested was -5 oC, -10 oC and -20 oC. Because the clay powder may be packed at different bed depth, the study was undertaken across the packing stress range at 8.3 kPa (1 m bed depth), 25.0 kPa (3 m) and 75.0 kPa (9 m). Freezing time varied between 4 hours (transport) and 18 hours (overnight). During the tests, failure of caked materials was measured using a QTS texture analyzer and the caking strength of frozen samples was calculated. Influences on freeze caking of granular clay in storage or transport are discussed briefly. Some conclusions are made at the end of the paper,including recommendations for practical methods for mitigating these problems.

Electrostatic modelling and measurement of airborne particles concentration

Granular air-borne particles generally carry very small amounts of electric charge as a consequence of charging by the triboelectric effect. The presence of such particles induces charge of opposite polarity on a stationary conducting electrode. The amount of charge carried by the particles and the trajectories of the particles have significant random components and the signals produced are of very low level. The signal processing is further complicated by the random variation in the concentration of particles, i.e. the solid/gas ratio. This paper compares the results obtained from the electrostatic modelling of such sensors with those obtained from experiments.

The palaeoenvironment and stratigraphy of Late Cretaceous Chalks

Since the publication of Hancock's ‘the Petrology of the Chalk’ there have been numerous developments in our appreciation of the palaeoenvironment and stratigraphie correlation of the UK Chalk. This work presents a review of some of the key developments over the last 30 years. Our detailed understanding of Chalk lithostratigraphy and advances in our understanding of chalk sedimentation indicate that large-scale mass transport and re-sedimentation of chalks by low-angle suspension flows is required to explain the observed thickness variations. The provenance of clay minerals and the process of flint and granular phosphate formation are discussed. The growing importance of isotopic studies in high resolution stratigraphy and improving our understanding of the late Cretaceous oceans and climate are emphasized. Developments in lithostratigraphic studies and recent proposals for a new stratigraphie division of the Chalk in the UK are evaluated.