Health of the older worker in Ireland - occupational physical and psychosocial factors in the autumn of work life

Introduction: Worldwide, governments are striving to keep people in work to an older age. However, little is known about the effects of work on an older workforce. This thesis aims to investigate the importance of job characteristics to the antecedents and evolution of cardiovascular disease and functional limitations for the older worker (50+ years). Methods: Three studies were used in this thesis. The 5C (Cork Coronary Care Case- Control) Study investigated the association between job strain and a coronary event in males (n=208) 35-74 years old. The Mitchelstown Study examined the association between job characteristics and positive lifestyle behaviours and further, job characteristics and blood pressure for males and females 50-69 years (n=2,047). Finally, the Cork & Kerry Study investigated the physical effects of manual work and reported functional limitations/disabilities in a sample of 60-80 year olds (n=362). Results: Results from the 5C Study show a clear difference between younger (<50 years) and older (≥50 years) workers, with older workers who had a coronary event more likely to have high job strain and low job control. Data from the Mitchelstown Study showed workers with intermediate possibility for development or high quantitative demands (versus low) at work significantly more likely to have co-occurrence of positive lifestyle behaviours. Further, those who had high possibility for development were more likely to have high systolic blood pressure with no indication of recovery from this activation at night. Physically demanding work as reported by the participants of the Cork & Kerry Study was associated with functional limitations and activities of daily living disability for both the paid and unpaid worker. Discussion: The findings from this piece of work highlight the necessity to examine job characteristics and health outcomes in isolation for the over fifties. The challenge is to get this information into the workplace.

AuxAg1-x alloy seeds: A way to control growth, morphology and defect formation in Ge nanowires

Germanium (Ge) nanowires are of current research interest for high speed nanoelectronic devices due to the lower band gap and high carrier mobility compatible with high K-dielectrics and larger excitonic Bohr radius ensuing a more pronounced quantum confinement effect [1-6]. A general way for the growth of Ge nanowires is to use liquid or a solid growth promoters in a bottom-up approach which allow control of the aspect ratio, diameter, and structure of 1D crystals via external parameters, such as precursor feedstock, temperature, operating pressure, precursor flow rate etc [3, 7-11]. The Solid-phase seeding is preferred for more control processing of the nanomaterials and potential suppression of the unintentional incorporation of high dopant concentrations in semiconductor nanowires and unrequired compositional tailing of the seed-nanowire interface [2, 5, 9, 12]. There are therefore distinct features of the solid phase seeding mechanism that potentially offer opportunities for the controlled processing of nanomaterials with new physical properties. A superior control over the growth kinetics of nanowires could be achieved by controlling the inherent growth constraints instead of external parameters which always account for instrumental inaccuracy. The high dopant concentrations in semiconductor nanowires can result from unintentional incorporation of atoms from the metal seed material, as described for the Al catalyzed VLS growth of Si nanowires [13] which can in turn be depressed by solid-phase seeding. In addition, the creation of very sharp interfaces between group IV semiconductor segments has been achieved by solid seeds [14], whereas the traditionally used liquid Au particles often leads to compositional tailing of the interface [15] . Korgel et al. also described the superior size retention of metal seeds in a SFSS nanowire growth process, when compared to a SFLS process using Au colloids [12]. Here in this work we have used silver and alloy seed particle with different compositions to manipulate the growth of nanowires in sub-eutectic regime. The solid seeding approach also gives an opportunity to influence the crystallinity of the nanowires independent of the substrate. Taking advantage of the readily formation of stacking faults in metal nanoparticles, lamellar twins in nanowires could be formed.

A new latching control technology for improving wave energy conversion

Extracting wave energy from seas has been proven to be very difficult although various technologies have been developed since 1970s. Among the proposed technologies, only few of them have been actually progressed to the advanced stages such as sea trials or pre-commercial sea trial and engineering. One critical question may be how we can design an efficient wave energy converter or how the efficiency of a wave energy converter can be improved using optimal and control technologies, because higher energy conversion efficiency for a wave energy converter is always pursued and it mainly decides the cost of the wave energy production. In this first part of the investigation, some conventional optimal and control technologies for improving wave energy conversion are examined in a form of more physical meanings, rather than the purely complex mathematical expressions, in which it is hoped to clarify some confusions in the development and the terminologies of the technologies and to help to understand the physics behind the optimal and control technologies. As a result of the understanding of the physics and the principles of the optima, a new latching technology is proposed, in which the latching duration is simply calculated from the wave period, rather than based on the future information/prediction, hence the technology could remove one of the technical barriers in implementing this control technology. From the examples given in the context, this new latching control technology can achieve a phase optimum in regular waves, and hence significantly improve wave energy conversion. Further development on this latching control technologies can be found in the second part of the investigation.