The development of an algorithm to track blood pressure accurately based on the pulse transit time method

Oscillometric blood pressure (BP) monitors are currently used to diagnose hypertension both in home and clinical settings. These monitors take BP measurements once every 15 minutes over a 24 hour period and provide a reliable and accurate system that is minimally invasive. Although intermittent cuff measurements have proven to be a good indicator of BP, a continuous BP monitor is highly desirable for the diagnosis of hypertension and other cardiac diseases. However, no such devices currently exist. A novel algorithm has been developed based on the Pulse Transit Time (PTT) method, which would allow non-invasive and continuous BP measurement. PTT is defined as the time it takes the BP wave to propagate from the heart to a specified point on the body. After an initial BP measurement, PTT algorithms can track BP over short periods of time, known as calibration intervals. After this time has elapsed, a new BP measurement is required to recalibrate the algorithm. Using the PhysioNet database as a basis, the new algorithm was developed and tested using 15 patients, each tested 3 times over a period of 30 minutes. The predicted BP of the algorithm was compared to the arterial BP of each patient. It has been established that this new algorithm is capable of tracking BP over 12 minutes without the need for recalibration, using the BHS standard, a 100% improvement over what has been previously identified. The algorithm was incorporated into a new system based on its requirements and was tested using three volunteers. The results mirrored those previously observed, providing accurate BP measurements when a 12 minute calibration interval was used. This new system provides a significant improvement to the existing method allowing BP to be monitored continuously and non-invasively, on a beat-to-beat basis over 24 hours, adding major clinical and diagnostic value.

Effect of solder volume on joint shape with variable chip-to-board contact pad ratio

The objective of this paper is to investigate the effect of the pad size ratio between the chip and board end of a solder joint on the shape of that solder joint in combination with the solder volume available. The shape of the solder joint is correlated to its reliability and thus of importance. For low density chip bond pad applications Flip Chip (FC) manufacturing costs can be kept down by using larger size board pads suitable for solder application. By using “Surface Evolver” software package the solder joint shapes associated with different size/shape solder preforms and chip/board pad ratios are predicted. In this case a so called Flip-Chip Over Hole (FCOH) assembly format has been used. Assembly trials involved the deposition of lead-free 99.3Sn0.7Cu solder on the board side, followed by reflow, an underfill process and back die encapsulation. During the assembly work pad off-sets occurred that have been taken into account for the Surface Evolver solder joint shape prediction and accurately matched the real assembly. Overall, good correlation was found between the simulated solder joint shape and the actual fabricated solder joint shapes. Solder preforms were found to exhibit better control over the solder volume. Reflow simulation of commercially available solder preform volumes suggests that for a fixed stand-off height and chip-board pad ratio, the solder volume value and the surface tension determines the shape of the joint.

Physical function, psychosocial adaptation, and hardiness post stroke

Introduction: Stroke is a chronic condition that significantly impacts on morbidity and mortality (Balanda et al. 2010). Globally, the complexity of stroke is well documented and more recently, in Ireland, as part of the National Survey of Stroke Survivors (Horgan et al. 2014). There are a number of factors that are known to influence adaptation post stroke. However, there is a lack of research to explain the variability in how survivors adapt post stroke. Hardiness is a broad personality trait that leads to better outcome. This study investigated the influence of hardiness and physical function on psychosocial adaptation post stroke. Methods: A quantitative cross-sectional, correlational, exploratory study was conducted between April and November 2013. The sample consisted of stroke survivors (n=100) who were recruited from three hospital outpatient departments and completed a questionnaire package. Results: The mean age of participants was 76 years (range 70-80), over half (56%) of the participants achieved the maximum score of 20 on the Barthel Index indicating independence in activities of daily living. The median number of days since stroke onset was 91 days (range 74-128). The total mean score and standard deviation for hardiness was 1.89 (0.4) as measured by the Dispositional Resilience Scale, indicating medium hardiness (possible range 0-3). Psychosocial adaptation was measured using the Psychosocial Adjustment to Illness Scale, the total weighted mean and standard deviation was 0.54 (0.3) indicating a satisfactory level of psychosocial adaptation (possible range 0-3). A hierarchical multiple linear regression was performed which contained 6 independent variables (hardiness, living arrangement, and length of hospital stay, number of days since stroke onset, physical function and self-rated recovery). Findings demonstrated that physical function (p<0.001) and hardiness (p=0.008) were significantly related to psychosocial adaptation. Altogether, 65% of the variation in psychosocial adaptation can be explained by the combined effect of the independent variables. Physical functioning had the highest unique contribution (11%) to explain the variance in psychosocial adaptation while self-rated recovery, hardiness, and living arrangements contributed 3% each. Conclusion: This research provides important information regarding factors that influence psychosocial adaptation post stroke at 3 months. Physical function significantly contributed to psychosocial adaptation post stroke. The personality trait of hardiness provides insight into how behaviour influenced adaptation post stroke. While hardiness also had a strong relationship with psychosocial adaptation, further research is necessary to fully comprehend this process.