Optimisation of granola breakfast cereal manufacturing process by wet granulation and pneumatic conveying

This study has considered the optimisation of granola breakfast cereal manufacturing processes by wet granulation and pneumatic conveying. Granola is an aggregated food product used as a breakfast cereal and in cereal bars. Processing of granola involves mixing the dry ingredients (typically oats, nuts, etc.) followed by the addition of a binder which can contain honey, water and/or oil. In this work, the design and operation of two parallel wet granulation processes to produce aggregate granola products were incorporated: a) a high shear mixing granulation process followed by drying/toasting in an oven. b) a continuous fluidised bed followed by drying/toasting in an oven. In high shear granulation the influence of process parameters on key granule aggregate quality attributes such as granule size distribution and textural properties of granola were investigated. The experimental results show that the impeller rotational speed is the single most important process parameter which influences granola physical and textural properties. After that binder addition rate and wet massing time also show significant impacts on granule properties. Increasing the impeller speed and wet massing time increases the median granule size while also presenting a positive correlation with density. The combination of high impeller speed and low binder addition rate resulted in granules with the highest levels of hardness and crispness. In the fluidised bed granulation process the effect of nozzle air pressure and binder spray rate on key aggregate quality attributes were studied. The experimental results show that a decrease in nozzle air pressure leads to larger in mean granule size. The combination of lowest nozzle air pressure and lowest binder spray rate results in granules with the highest levels of hardness and crispness. Overall, the high shear granulation process led to larger, denser, less porous and stronger (less likely to break) aggregates than the fluidised bed process. The study also examined the particle breakage of granola during pneumatic conveying produced by both the high shear granulation and the fluidised bed granulation process. Products were pneumatically conveyed in a purpose built conveying rig designed to mimic product conveying and packaging. Three different conveying rig configurations were employed; a straight pipe, a rig consisting two 45° bends and one with 90° bend. Particle breakage increases with applied pressure drop, and a 90° bend pipe results in more attrition for all conveying velocities relative to other pipe geometry. Additionally for the granules produced in the high shear granulator; those produced at the highest impeller speed, while being the largest also have the lowest levels of proportional breakage while smaller granules produced at the lowest impeller speed have the highest levels of breakage. This effect clearly shows the importance of shear history (during granule production) on breakage during subsequent processing. In terms of the fluidised bed granulation, there was no single operating parameter that was deemed to have a significant effect on breakage during subsequent conveying. Finally, a simple power law breakage model based on process input parameters was developed for both manufacturing processes. It was found suitable for predicting the breakage of granola breakfast cereal at various applied air velocities using a number of pipe configurations, taking into account shear histories.

Impact of the smoke-free workplace legislation on smoking behaviour, risk perception & stigmatisation

The Republic of Ireland became the first European country to implement nationwide smoke-free workplace legislation. Aims: To determine prevalence of smoking among bar workers and estimate the impact of the smoke-free workplace legislation on their smoking behaviour to that of a comparable general population sample. To approximate the influence of tobacco control measures on risk perception of second-hand smoke (SHS) among the general population. To explore the de-normalisation of smoking behaviour and the potential increased stigmatisation of smokers and their smoking. Methods: Prevalence estimates and behavioural changes were examined among a random sample of bar workers before and 1 year after the smoke-free legislation; comparisons made with a general population sub-sample. Changes in risk knowledge related to SHS exposure were based on general population data. Qualitative interviews were conducted among a purposive sample of smokers and non-smokers four years after the implementation of the legislation. Results: Smoking prevalence was extremely high among bar workers. Smoking prevalence dropped in bar workers and significantly among the general population 1 year post ban while cigarette consumption dropped significantly among bar workers. Disparity in knowledge between smokers and non-smoker of risk associated with SHS exposure reduced. Lack of understanding of the risk of ear infections in children posed by SHS exposure was notable. Evidence for advanced de-normalisation of smoking behaviour and intensification of stigma because of the introduction of the legislation was dependent on many factors, quality of smoking facilities played a key role. Conclusions: Ireland’s smoke-free legislation was associated with a drop in prevalence and cigarette consumption. Disparity in knowledge between smokers and non-smokers of the risk posed by SHS exposure reduced however the risk of ear infections in children needs to be effectively disseminated. The proliferation of ‘good’ smoking areas may diminish the potential to reduce smoking behaviour and de-normalise smoking.

Development of low-cost sensing and separation devices based on macro, micro and nano technology for health applications

The work presented in this thesis described the development of low-cost sensing and separation devices with electrochemical detections for health applications. This research employs macro, micro and nano technology. The first sensing device developed was a tonerbased micro-device. The initial development of microfluidic devices was based on glass or quartz devices that are often expensive to fabricate; however, the introduction of new types of materials, such as plastics, offered a new way for fast prototyping and the development of disposable devices. One such microfluidic device is based on the lamination of laser-printed polyester films using a computer, printer and laminator. The resulting toner-based microchips demonstrated a potential viability for chemical assays, coupled with several detection methods, particularly Chip-Electrophoresis-Chemiluminescence (CE-CL) detection which has never been reported in the literature. Following on from the toner-based microchip, a three-electrode micro-configuration was developed on acetate substrate. This is the first time that a micro-electrode configuration made from gold; silver and platinum have been fabricated onto acetate by means of patterning and deposition techniques using the central fabrication facilities in Tyndall National Institute. These electrodes have been designed to facilitate the integration of a 3- electrode configuration as part of the fabrication process. Since the electrodes are on acetate the dicing step can automatically be eliminated. The stability of these sensors has been investigated using electrochemical techniques with excellent outcomes. Following on from the generalised testing of the electrodes these sensors were then coupled with capillary electrophoresis. The final sensing devices were on a macro scale and involved the modifications of screenprinted electrodes. Screen-printed electrodes (SPE) are generally seen to be far less sensitive than the more expensive electrodes including the gold, boron-doped diamond and glassy carbon electrodes. To enhance the sensitivity of these electrodes they were treated with metal nano-particles, gold and palladium. Following on from this, another modification was introduced. The carbonaceous material carbon monolith was drop-cast onto the SPE and then the metal nano-particles were electrodeposited onto the monolith material

Chillaxin'

A jazz piece for solo piano and/or jazz ensemble. This piece combines traditional and contemporary approaches. It is primarily old style swing but incorporates many modern harmonic techniques/devices, as evidenced in the score, such as: the use of upper structure triads, drop two voicing techniques, and voicing in fourths.

Study on street children in four selected towns of Ethiopia

The child is the most precious asset and the focal point of development for any country. However, unless children are brought up in a stimulating and conducive environment getting the best possible care and protection, their physical, mental, emotional and social development is susceptible to permanent damage. Ethiopia, being one of the least developed countries of the world due to interrelated and complex socio-economic factors including man-made and natural calamities, a large portion of our population - especially children - are victimized by social evils like famine, disease, poverty, mass displacement, lack of education and family instability. Owing to the fact that children are the most vulnerable group among the whole society and also because they constitute half of the population it is evident that a considerable number of Ethiopian children are living under difficult circumstances. Therefore, as in a number of other third world countries there are many poor, displaced, unaccompanied and orphaned children in our country. A considerable proportion of these children work on the street with some even totally living on the street without any adult care and protection. These children are forced to the streets in their tight for survival. They supplement their parents meagre income or support themselves with the small incomes they earn doing menial jobs. In doing this, street children face the danger of getting into accidents and violence, they get exploited and abused, many are forced to drop out of school or never get the chance to be enroled at all and some drift into begging or petty crime. This study is undertaken mainly for updating the findings of previous studies, monitoring changing trends, examining new facts of the problem and getting a better understanding of the phenomenon in the country by covering at least some of the major centres where the problem is acute. Thus, the outcome of this research can be useful in the formation of the social welfare programme of the country. Finally, in recognition of the urgency of the problem and the limited resources available, the Ministry of Labour and Social Affairs expresses appreciation to all agencies engaged in the rehabilitation of street children and prevention of the problem. The Ministry also calls for more co-operation and support between concerned governmental and non-governmental organizations in their efforts for improving the situation of street children and in curbing the overwhelming nature of the problem.